石英纤维增强苯并噁嗪树脂复合材料研究

对苯并(啞心)嗪树脂应用于RTM工艺制备石英纤维增强复合材料进行了研究.系统考察了该树脂的工艺性能及力学性能,制备并测试了石英/苯并(啞心)嗪复合材料的力学性能及耐烧蚀性能,并将相关性能与钡酚醛与石英/钡酚醛进行了比较.结果表明,在85℃～145℃温度区间内苯并(啞心)嗪树脂粘度保持在800mPa·s以下,树脂具有较宽的低粘度温度平台和较长的低粘度保持时间.力学性能及耐烧蚀性能研究表明,石英/苯并(啞心)嗪复合材料的层间剪切强达到了61.5MPa,拉伸强度和弯曲强度显著优于石英,钡酚醛复合材料,质量烧蚀率和线烧蚀率分别为0.0510g·s-1和0.032mm·s-1.石英/苯并(啞心)嗪复合材料是一种可采用RTM工艺制备的耐烧蚀材料.     

低粘度环氧树脂VIMP工艺性能研究

VIMP(真空注射模塑)工艺以其低成本、环保和适于大型制件一次整体成型等优点得到了广泛应用.本文对VIMP工艺用低粘度环氧树脂体系进行了固化反应动力学和粘度分析,确定了最佳固化温度,建立了树脂体系的流变模型,模型分析结果与实验结果吻合较好,根据此流变模型预报了工艺窗口.并进行了VIMP模塑板材工艺实验,测试了板材的纤维体积含量和力学性能.     

整体缝合夹芯结构复合材料力学性能

所设计的新型整体缝合泡沫夹芯复合材料结构,能够避免一般斜缝方式引起纤维交叉损坏的弊端。采用真空导入模塑工艺制备整体缝合泡沫夹芯结构复合材料,研究缝合结构、缝合方式以及缝合纱线用量对整体缝合泡沫夹芯复合材料平压力学性能和弯曲性能的影响。结果表明,新型缝合结构在保证平压力学性能的同时,相比于垂直缝合结构弯曲破坏载荷提高了94.4%;穿透缝合方式能够显著提高试样的平压强度和弯曲破坏载荷;随着缝合纱线用量的增加,整体缝合泡沫夹芯复合材料的压缩和弯曲性能显著提高。     

注胶修复工艺的耐高温环氧树脂体系工艺性能

针对注胶修复工艺要求,采用差示扫描量热法热分析和流变仪测试三种中温固化配方的耐高温缩水甘油胺型环氧树脂体系的固化特性和化学流变特性,通过对比分析三种配方树脂体系的固化条件和黏度特性,确定MF-4101/ZH110/DMP-30树脂体系为最适宜注胶修复工艺的配方。建立该树脂体系在等温条件下黏度特性曲线的Daul Arrhenius模型和高阶指数拟合模型。结果表明,高阶指数拟合模型的预测精度和适用范围均优于Daul Arrhenius模型,预测黏度与实验结果具有良好的一致性,根据高阶指数拟合模型建立的黏度随温度、时间变化的唯象关系式,可以准确地预报修复树脂体系的工艺窗口。     

改性双酚A环氧树脂固化机理及其性能

用脂环族三官能度环氧树脂TDE-85改性双酚A型环氧树脂,达到提高耐热性与强韧性的目的.利用DSC对其固化反应机理进行了深入研究,并借助DDA确定中温固化工艺,对中温固化树脂基体的力学性能和热性能的研究表明固化物力学性能优良,与普通双酚A型树脂相比,相同固化体系树脂浇铸体的拉伸强度由47.30 MPa提高到 70.50 MPa,弯曲强度由62.74 MPa提高到85.48 MPa,冲击韧性由9.08×103 J/m2提高到1.09×104 J/m2,拉伸强度、断裂延伸率、弯曲强度及冲击韧性分别提高49.05%、50.0%、36.24%及19.53%.IR 分析表明,固化物的固化度为92.3%.     

吸湿环境对石英纤维增强环氧树脂面板/PMI泡沫夹层结构复合材料吸湿行为的影响

研究了不同温度、湿度环境下,夹层结构石英纤维增强环氧树脂面板/PMI泡沫夹层结构复合材料及其芯材和面板的吸湿规律。将石英纤维增强环氧树脂面板、PMI泡沫、复合材料面板/PMI泡沫夹层结构试样在不同吸湿环境中进行吸湿处理后,对其吸湿行为进行分析。结果表明:浸水环境下面板、PMI泡沫、PMI泡沫夹层结构复合材料都表现出更为严重的吸湿行为;在潮湿环境中,50℃至70℃范围内,温度越高,试样在吸湿过程中的质量损失越多,最终的饱和吸湿率越小;在60℃以内的潮湿环境中,PMI泡沫夹层结构复合材料的饱和吸湿率可以通过相同环境下面板复合材料和PMI泡沫的吸湿率进行预测。     

一种低黏度环氧树脂的制备及性能研究

采用一种新型增韧剂CC对环氧树脂进行增韧改性,获得一种低黏度中温固化环氧树脂体系。测试了树脂的力学性能,并通过红外光谱和动态热机械能分析等方法,对树脂的组织和性能进行了研究。结果表明：当CC的质量分数为19%时,环氧树脂的剪切强度和拉伸强度最大,分别为25.1 MPa和55.88 MPa;该环氧树脂具有较低的黏度;固化过程中各组分反应完全,树脂刚度较大,玻璃温度Tg达110.36℃。     

烧结温度对 Cf/SiC 复合材料界面的影响

系统地研究了烧结温度对Cf/SiC复合材料界面和力学性能的影响.结果表明,烧结温度较低(1700℃)时,由于复合材料的烧结性差,纤维与基体间仅仅为一种机械结合,因此纤维与基体间结合很弱,从而导致复合材料力学性能低.烧结温度提高至1800℃后,由于适量的富碳界面相不仅可避免纤维与基体间的直接结合,而且使纤维与基体间的结合强度适中,因而复合材料具有很好的力学性能.进一步提高烧结温度至1850℃或更高温度时,由于界面相与纤维间的反应加重,纤维本身性能大大降低.同时,纤维与基体间结合强度提高,因此复合材料的力学性能大大降低.     

偏磷酸铝在Cf/AL 复合材料中的应用

以高模高强石墨纤维Ｍ４０Ｊ增强铝基复合材料为研究对象,研究了真空液相压渗工艺中,偏磷酸铝粘接剂对纤维预制件抗压性能及复合材料力学性能的影响。结果表明：偏磷酸铝的含量、Ａｌ／Ｐ原子比及处理温度对预制件的抗压性能均有显著影响,加入５％偏磷酸铝粘接剂溶液的预制件,经５００°Ｃ处理后的抗压性能满足压渗要求,纤维保持了较好的平直度及分布均匀性,所制备的复合材料抗拉强度大于５００ＭＰａ,抗弯强度大于８００ＭＰａ     

反应性树脂体系化学增黏和物理减黏机制的分离

采用等温差示扫描量热(DSC)法,研究了CTD-128环氧树脂与GA-327(DDM改性芳胺)的固化度-时间变化关系;采用AR2000EX型旋转流变仪,测试了上述体系的等温黏度-时间关系.比较等温条件下的固化度-时间关系和黏度-时间关系,建立了等温条件下的黏度-固化度的等时对应关系,结果表明在纯化学增黏机制影响下,树脂体系的黏度随固化度增加先缓慢增加,当固化度增大到一定程度后黏度快速增加.将等温条件下的黏度-固化度关系进行变换,得到恒定固化度下的黏度-温度关系,揭示了在物理减黏机制影响下,树脂体系黏度随温度的增加而降低,并且黏度降低幅度随固化度的增加而增大.两种黏度影响机制分离的实现,为反应性树脂体系实时黏度的准确预测提供了技术支持.     

Helping hands: civil–military cooperation and Italy's military operation abroad

In the Post-Bipolar Era the growing complexity of the military operations requires a new approach for the resolution of international crises. Since the end of the Cold War, peace support operations (PSO) have become the mainstay and principal occupation of most Western armies. At the same time, Italy has been one of the most important actors in such an area. The article focuses on the cooperation between military and civil components (a process called CIMIC) as a key variable in the Italian PSOs. We will analyse in detail the main lessons learned from past military interventions as well as the general context in which new tendencies are taking place. The maintaining of a minimum security frame becomes essential to fulfil activities ‘collateral’ to the mission: reconstructing services and infrastructure, food distribution, water and medication, law and order, de-mining, training of local forces, and supporting local institutions. These are the main tasks to obtain thrust and support from the population.     

Terrorism,insurgency, kidnapping,and security in Africa's energy sector

Energy continues to serve as the bedrock of modern economies and the main driver of modern society. For Africa, the production and supply of energy resources such as crude oil, natural gas, uranium, coal, biomass, biofuels and other renewables are an important source of employment, rents, taxes, royalties and profits. This sector brings in several tens of billions of dollars of revenue annually. The production and delivery of such resources, however, depend on critical infrastructures such as pipelines, refineries, processing plants, terminals, rigs, electrical energy pylons, substations, pump stations, vessels, and tankers. These infrastructures have been attacked by terrorists, insurgents, vandals and saboteurs, all of whom see them as targets against which to register their grievances and extract concessions from the state. This paper is a chronological account of some of the documented incidents of terrorism, insurgency, kidnapping, destruction, sabotage, and human casualties suffered in the oil and gas sectors in Africa between 1999 and 2012. It is based on data extracted from the databases of the RAND Database of World Terrorism Incidents and the University of Maryland's Global Terrorism Database (GTD).     

A1 Qaeda and the radical Islamic challenge to western strategy

The September 11 global crisis prompted by the attacks on the World Trade Center and the Pentagon raises major questions concerning the nature and trajectory of terrorism in the post-Cold War global order. Hitherto, terrorism has been largely debated by analysts at the level of nation states. Terrorist and insurgent movements have also been largely anchored in nationalist and ethnic power bases even when they have sought to mobilise a transnational ideological appeal on religious or class grounds. There have been a few exceptions to this pattern such as the alliance between the German Baader-Meinhof group and the Japanese Red Army Faction, but even such international alliances as this did not, until at least the 1980s, presage anything like a global terrorist network necessitating a global strategic response. This study examines terrorism and global strategic responses.     

Tacit support for terrorism: The rapprochement between the USSR and Palestinian guerrilla organizations following the 1967 war

This article demonstrates the inconsistent and wavering Soviet attitude towards national liberation movements in general and the Palestinian organizations in particular. Until the late 1960s, the Soviets viewed these organizations with suspicion, hesitating to engage in political dialogue with them. However, in the 1970s, political and military events in the region, as well as modifications in the Kremlin's Cold War strategies, led to a general shift towards the Middle East in Soviet foreign policy. Soviet leaders showed increased willingness to provide certain Palestinian organizations with arms with which to conduct terrorist activities against Israeli, pro-Israeli, Jewish and Western targets. The article explores the complex relations between Palestinian organizations and the USSR in the field of international terror. The study also exposes and analyzes the nature and content of Soviet–Palestinian arms dialogues and transactions. It provides clear evidence that Soviet policymakers and other luminaries were fully informed of, and sometimes directly involved in, these transactions and dialogues at the highest levels.     

Helping hands: external support for the KNU insurgency in Burma

This article analyses to what extent the Burmese KNU insurgency made use of external support from states, refugees, and diasporas. Based on extensive fieldwork it is concluded that support from neighbouring states and refugees has for years kept the Karen rebellion alive. Western countries perceived forms of resistance to the illegitimate Burmese regime as just and have therefore played a crucial role in the continuation of conflict in Karen State. It is important that policymakers and donors as well as executing organizations continue to reflect critically on the way they exercise their work.     

基于GTST-DMLD-ESD的装备RMS建模仿真

装备的RMS是装备的重要设计参数,是影响战备完好和保障能力的关键因素.引入GTST-DMLD作为主要建模工具,建立起装备系统的RMS描述模型,以ESD为补充和扩展,对维修过程进行建模.并以GTST-DMLD-ESD模型作为装备RMS仿真的核心,对装备RMS仿真模型的总体框架进行了研究,并对各模块进行了较为详细的探讨.     

Cyber sheiks and grassroots jihadis: the war in Syria and the devolution of the Bosnian Salafi communities

ABSTRACT

What was the scope of the Bosnian jihadi participation in the war in Syria? Did the Bosnian volunteers tend to join one particular faction? Why did the Bosnian youngsters decide to join the holy war in the Levant? Was this an organized and hierarchical process or was this a grassroots movement? Last, were all the Salafis in Bosnia supportive of this dynamic or did this process cause internal frictions? These are some of the questions that this research will try to answer.     

Country survey XVI the defence sector in the economy of a declining superpower: Soviet Union and Russia, 1965-2001

The Soviet Union was able to develop a large military-industrial complex and become the world's second superpower despite deficiencies in its centrally planned economy because defence was given high priority status and special planning, rationing and administrative mechanisms were used to attain national security objectives. However, in the period 1976-85 the effectiveness of priority protection diminished and defence institutions experienced more of the problems typical of the shortage economic system. The heavy defence burden also created growing difficulties for the civilian economy. The attempts by the Gorbachev government to reform the defence sector and improve defence-economic relationships during perestroika (1985-91) uniformly failed. For most of the transition period, the Russian military-industrial complex has been adversely affected by its low priority status, cuts in defence spending, instability of the hybrid politico-economic system, and negative growth of the economy. The armed forces and defence industry have been reduced in size and their outputs of military services and equipment have fallen to low levels. Nevertheless, the Russian armed forces still have over one million troops, significant stocks of sophisticated conventional weapons, and a large nuclear arsenal. The government of President Putin has raised the priority of the defence sector, increased real defence spending, and adopted ambitious plans to revive Russian military power. It is likely, though, that tight resource constraints will hamper efforts to reform the armed forces and to upgrade weapons. By 2010 Russia will be an important, but not dominant, military power in Eurasia.     

Traffickers,terrorists, and a ‘new security challenge’: Russian counternarcotics strategy and the Federal Service for the Control of the Drugs Trade

The collapse of the Soviet Union precipitated the massive expansion of drug use and trade in Russia. The country now has one of the largest populations of injecting drug users in the world and has become the largest single-country market for Afghan heroin. In 2003 the Federal Service for the Control of the Drugs Trade was created to coordinate a comprehensive counternarcotics strategy appropriate to the scale of this threat. The service continues to face a number of challenges in its early stages of development. However, it has made considerable advances in improving responses to large-scale organised crime and in building international cooperation.