Theoretical and numerical simulation study on jet formation and penetration of different liner structures driven by electromagnetic pressure

The use of a shaped liner driven by electromagnetic force is a new means of forming jets. To study the mechanism of jet formation driven by electromagnetic force, we considered the current skin effect and the characteristics of electromagnetic loading and established a coupling model of"Electric—Magnetic—Force"and the theoretical model of jet formation under electromagnetic force. The jet formation and penetration of conical and trumpet liners have been calculated. Then, a numerical simulation of liner collapse under electromagnetic force, jet generation, and the stretching motion were performed using an ANSYS multiphysics processor. The calculated jet velocity, jet shape, and depth of penetration were consistent with the experimental results, with a relative error of less than 10％. In addition, we calculated the jet formation of different curvature trumpet liners driven by the same loading condition and ob-tained the influence rule of the curvature of the liner on jet formation. Results show that the theoretical model and the ANSYS multiphysics numerical method can effectively calculate the jet formation of liners driven by electromagnetic force, and in a certain range, the greater the curvature of the liner is, the greater the jet velocity is.     

A numerical study on the disturbance of explosive reactive armors to jet penetration

The disturbance of flat and V-shaped sandwich reactive armor configurations to shaped-charge jet is studied by a numerical approach. The disturbing and cutting effects of the two reactive armor configurations to the jet are successfully captured. The predicted disturbance characteristics and patterns are in fairly good agreement with the X-ray photographic observations. The residual depth of penetration into a semi-infinitive homogeneous steel target behind the reactive armor is computed for a series of jet/armor parameters. For the flat configuration, it is demonstrated that the residual penetration depth is not significantly reduced for a normal impact while it is reduced up to 75% for an oblique impact. In comparison, the V-shaped configuration reduces the penetration depth of the jet to 90%, and it is observed that the penetration depth is not sensitive to the V-shaped angle.     

不同边界条件下水下爆炸气泡的数值模拟

采用有限元程序MSC.Dytran对不同边界条件下水下爆炸气泡的脉动过程进行了数值模拟。对数值模拟中的一些重要问题,如炸药药包的建模、网格密度、状态方程和静压力场的设定等问题进行了探讨。对无限水域中的水下爆炸气泡以及自由面边界、水平刚性面边界和垂直刚性面边界三种边界条件下的水下爆炸气泡进行了数值模拟,分析了水下爆炸气泡的半径、外形变化、气泡脉动压力、流场中的速度分布,结果发现边界的存在对气泡外形的影响较大,刚性边界面会使气泡脉动压力增大较多,而自由面边界对气泡脉动压力的影响较小。将数值模拟的结果与理论模型、经验公式和试验结果进行了比较分析,结果吻合较好。     

轴对称淹没水射流喷管内外紊流流场数值模拟

利用淹没水射流可对有机物进行降解.为研究淹没水射流降解的流场特性,根据轴对称淹没水射流撞击靶件的条件建立了物理模型,选用κ-ε紊流模型采用SIMPLEC算法进行数值计算.计算结果表明,流场存在射流区、漫流区、撞击区和漩涡区:射流区离靶件较远的部分同自由射流结构相似;靶件冲击面上压力分布近似的呈正态分布.对物理模型进行适当的改进并进行模拟,其结果同相应的实验数据相吻合,验证了本模型的可行性和计算结果的正确性.     

Numerical simulation of the natural fragmentation of explosively loaded thick walled cylinders

The ability to predict the natural fragmentation of an explosively loaded metal casing would represent a significant achievement. Physically-based material models permit the use of small scale laboratory tests to characterise and validate their parameters. The model can then be directly employed to understand and design the system of interest and identify the experiments required for validation of the predictions across a wide area of the performance space. This is fundamentally different to the use of phenomenologically based material algorithms which require a much wider range of characterisation and validation tests to be able to predict a reduced area of the performance space. Eulerians numerical simulation methods are used to describe the fragmentation of thick walled EN24 steel cylinders filled with PBXN-109 explosive. The methodology to characterise the constitutive response of the material using the physically based Armstrong–Zerilli constitutive model and the Goldthorpe path dependent fracture model is described, and the results are presented. The ability of an Eulerian hydrocode to describe the fragmentation process and reproduce the experimentally observed fragment mass and velocity distributions is presented and discussed. Finally the suitability of the current experimental analysis methodology for simulation validation is addressed.     

凝结水泵三维流场数值模拟与分析

为深入理解和分析电站凝结水泵性能,采用计算流体力学方法(CFD)对其内部复杂的三维流场进行了数值模拟与分析.首先,建立了某三级凝结水泵各部件几何模型,并对其进行网格划分.通过求解RANS方程对凝结水泵内部三维流场进行数值求解,湍流流动采用SST模型进行模拟.计算得到该泵若干工况下的扬程和功率等性能参数和泵内部流动特征,计算结果与试验数据吻合很好.模拟结果及分析表明:采用CFD方法模拟结构复杂的凝结水泵内部流动和进行性能预报是可行的.通过内流场分析还发现导叶体等部件的设计有可改进之处.     

破甲弹侵彻装甲板的数值仿真

装甲装备受到弹丸攻击后,要判断内部部件的毁伤情况,采用实弹试验的方法费用高,周期长,安全性差;而采用建模仿真的方法费用低,效率高,安全性好,并且可以为预测装备内部的毁伤部件奠定基础。采用有限元法对破甲弹侵彻均质装甲板进行了数值仿真,对侵彻过程的3个阶段进行了分析,得出了破甲弹射流的动能、平均速度和冲量随时间变化的规律,为侵彻后装甲板内部部件毁伤情况的判断提供了基础数据。     

轴对称物体空泡流动的数值计算

基于势流理论和边界元方法,对水下运动的回转体的空泡流进行了数值模拟.将半经验空泡封闭模型由平面流动推广至轴对称流动.对头部为圆锥的圆柱体空泡流动进行了数值计算.分析了空化数、半锥角、空泡长度间的关系.计算与实验结果符合较好.     

分解炉内煤粉燃烧和CaCO3分解流场的数值模拟

针对国内某大型水泥高性能分解炉,基于Fluent软件,采用有限速率/涡耗散模型模拟了炉内煤粉燃烧和生料分解的湍动多相流场,给出了炉内速度矢量、温度、压力和组分分布,结果显示,炉内流动趋势合理,可为分解炉的研究提供参考.     

Numerical simulation study on penetration performance of depleted Uranium (DU) alloy fragments

Due to its high strength, high density, high hardness and good penetration capabilities, Depleted ura-nium alloys have already shined in armor-piercing projectiles. There should also be a lot of room for improvement in the application of fragment killing elements. Therefore, regarding the performance of the depleted uranium alloy to penetrate the target plate, further investigation is needed to analyze its advantages and disadvantages compared to tungsten alloy. To study the difference in penetration per-formance between depleted uranium alloy and tungsten alloy fragments,firstly, a theoretical analysis of the adiabatic shear sensitivity of DU and tungsten alloys was given from the perspective of material constitutive model. Then, taking the cylindrical fragment penetration target as the research object, the penetration process and velocity characteristics of the steel target plates penetrated by DU alloy frag-ment and tungsten alloy fragment were compared and analyzed, by using finite element software ANSYS/LS-DYNA and Lagrange algorithm. Lastly, the influence of different postures when impacting target and different fragment shapes on the penetration results is carried out in the research. The results show that in the penetration process of the DU and tungsten alloy fragments, the self-sharpening properties of the DU alloy can make the fragment head sharper and the penetrating ability enhance. Under the same conditions, the penetration capability of cylindrical fragment impacting target in vertical posture is better than that in horizontal posture, and the penetration capability of the spherical fragment is slightly better than that of cylindrical fragment.     

旋转泵式鱼雷发射系统建模与仿真

介绍了由高压气瓶、发射阀、喷射式空气轮机、混流泵组成的一种新型旋转泵式鱼雷发射系统,建立了该系统的仿真模型,对鱼雷发射过程进行了仿真并对结果作了分析.     

半穿甲导弹性能的攻角效应数值分析

利用LS—DYNA软件分析弹体攻角和目标运动对穿甲过程中装药安定性、弹体剩余速度及弹头姿态的影响。在穿甲过程中,弹体速度为300m／s,攻角分别为0°,10°和20°,弹体和目标板选择了考虑应变、应变率和温度效应的Johnson—cook材料模型。结果表明：随攻角的增大,装药局部受力显著增大,弹体剩余速度下降,弹头发生偏转;目标运动使穿甲能力减弱,但目标运动会使装药受到的外力在一定程度上减少。     

架构和模式在水声信息流仿真软件中的应用

水声信息流仿真软件系统涉及多目标、多声纳以及多变的海洋环境.仿真软件的复用性是现代软件工程的重要性能指标.针对系统开放性的特点,在领域分析模型的基础上,采用了面向对象方法设计仿真软件模型.为了满足软件多层次复用的需求,应用软件架构技术和设计模式设计仿真软件.根据水声信息流仿真软件需求,系统划分为四层结构;按功能,层又可分解为包.可复用的设计模式用于设计不同层和包中类之间的关系.提出的仿真软件模型具有良好的可扩充性与可复用性.     

制导航空子母炸弹高速抛撒分离数值仿真

制导航空子母炸弹在跨音速抛撒子弹药过程中,子弹药与母弹的分离伴随着复杂的流场和激波干扰,该过程中不仅存在着激波与激波的相互碰撞、部分激波的多次反射,而且由于受到多体运动的相互作用,其气流方向也发生变化,形成了变化复杂的压力、速度分布区域。采用数值模拟的方法对制导航空子母炸弹子弹药高速抛撒分离过程进行了数值仿真分析,应用嵌套网格技术,耦合多体动力学方程以及 N－S 方程求解子母炸弹高速分离过程,为工程设计、研究提供理论指导与计算依据。     

稀相气力输送CFD-DEM仿真中两种模型的比较

比较了两种不同的CFD-DEM数学模型(模型A和简化模型A)在稀相气力输送数值模拟中的性能。简化模型A忽略了空隙率对气相的影响,在节省仿真时间的同时也提高了计算的稳定性。使用两种模型分别对带有弯管的稀相气力输送系统进行了仿真,对比仿真结果表明:两种模型对颗粒绳分散速度和弯管出口处颗粒分布的预测几乎一致,对弯管入口处颗粒速度和弯管中接触信息的预测也仅存在较小差别。     

受限空间雾化射流降温与加湿作用数值分析

以雾化射流预防、控制受限空间内油气热安全事故为工程背景,综合可压缩流场控制方程、k-ε湍流模型、粒子动力学模型与相变传热模型,构建了描述受限空间内雾化射流降温与加湿作用的数值分析模型。借助Fluent流体动力学仿真软件,以1 600 mm×200 mm二维狭长受限空间中不同工况的雾化射流为算例,对雾化射流降温与加湿过程进行了数值模拟,并探讨了雾化射流流量与粒径的不同对上述作用的影响。所得结果为进一步探究雾化射流降温与加湿行为,推进雾化射流在热安全防护领域的工程应用提供借鉴和参考。     

高超音速导弹气动光学效应研究方法综述

气动光学效应是高超音速导弹设计需要解决的关键技术。全面论述了气动光学效应的定量研究方法,包括:小孔径技术、统计方法、随机相位屏方法和涡动力学研究方法,指出了工程上广泛使用的统计方法的适用范围,建议使用大涡模拟方法进行气动光学效应的数值仿真。     

考虑摩擦时环状流的空泡份额求解

在熵增模型的基础上,考虑壁面摩擦对空泡份额的影响,推导出了空泡份额应满足的方程,求得其解析解和数值解,并进行了讨论.分析表明,其结果包含了有关文献的结果,具有更大的适用范围.     

分解炉内气固两相流场不同模型模拟结果分析

针对某高性能水泥分解炉的实际尺寸,分别采用Eulerian模型、mixture模型和离散相模型模拟了炉内气固两相三维流场,结果显示Eulerian(mixture)模型模拟所得炉内速度、压力、温度场以及固相体积分数梯度结果整体上优于其它模型,其流动趋势和规律与该分解炉的优质性能定性符合.