预应力CFRP筋T形梁受弯性能试验及变形分析

试验通过对3根T形预应力CFRP筋混凝土梁和1根矩形预应力CFRP筋混凝土梁进行对比,考察了预应力CFRP筋混凝土梁的受弯工作性能,记录了试验梁的开裂荷载、极限荷载和裂缝发展情况。试验结果表明：增加预应力度和总配筋率对提高开裂荷载,限制挠度、裂缝发展起重要作用;相同配筋的T形梁和矩形梁挠度相近,但各阶段荷载不同。对预应力CFRP筋T形梁的变形性能进行了理论分析,推导了短期荷载作用下刚度和挠度的计算公式,并将计算值与试验值进行比较,两者吻合良好。     

侧贴碳纤维布加固连续梁非线性有限元分析

为研究不同初始荷载作用下侧贴碳纤维布及侧贴预应力碳纤维布加固钢筋混凝土连续梁的加固效果,采用有限元分析软件ABAQUS对其进行数值模拟,并将有限元分析结果与试验结果对比。有限元分析表明：钢筋混凝土连续梁的加固效果受初始荷载的影响,初始荷载越小,加固效果越好;对纵向侧贴碳纤维布施加预应力,能够大幅提高钢筋混凝土连续梁的抗弯承载力,与未加固梁相比其抗弯承载力提高了65%以上;有限元计算结果与试验结果的荷载-挠度曲线吻合较好,两者的抗弯承载力相差不超过10%。所得结果可以为类似加固设计和试验提供参考。     

Optimization of process parameters of the activated tungsten inert gas welding for aspect ratio of UNS S32205 duplex stainless steel welds

The activated TIG (ATIG) welding process mainly focuses on increasing the depth of penetration and the reduction in the width of weld bead has not been paid much attention. The shape of a weld in terms of its width-to-depth ratio known as aspect ratio has a marked influence on its solidification cracking tendency. The major influencing ATIG welding parameters, such as electrode gap, travel speed, current and voltage, that aid in controlling the aspect ratio of DSS joints, must be optimized to obtain desirable aspect ratio for DSS joints. Hence in this study, the above parameters of ATIG welding for aspect ratio of ASTM/UNS S32205 DSS welds are optimized by using Taguchi orthogonal array (OA) experimental design and other statistical tools such as Analysis of Variance (ANOVA) and Pooled ANOVA techniques. The optimum process parameters are found to be 1 mm electrode gap, 130 mm/min travel speed, 140 A current and 12 V voltage. The aspect ratio and the ferrite content for the DSS joints fabricated using the optimized ATIG parameters are found to be well within the acceptable range and there is no macroscopically evident solidification cracking.     

一种鱼雷自导信号频率检测方法研究

靶场在进行智能鱼雷鉴定试验任务时,实时准确地检测出鱼雷自导信号的频率成分是靶标信号处理中的重要环节,谱线比值法便是靶标进行信号处理时检测信号频率的一种有效方法。本文介绍了谱线比值法的基本原理,针对目前鱼雷自导信号特点,对该方法提出了改进方案并进行了仿真。仿真结果表明,经改进的谱线比值法能够满足靶标检测复杂鱼雷自导信号体制下信号频率的使用要求。     

基于低速平台的随队支援干扰系统随队干扰能力分析

为了给受训对象提供电磁信号环境,在随队干扰信号从雷达天线主波束进入的限定条件下,设计了使用低速平台搭载干扰系统伴随高速战机实施随队干扰的编队方式,并仿真分析了对不同主瓣宽度雷达的随队干扰过程。结果表明,当平台速度明显低于突击飞机飞行速度时,存在最佳的初始进入距离以实现最大局部随队干扰过程。     

非相干背景光辐照二波耦合中的最佳匹配随机共振

针对非相干背景光辐照二波耦合中参数的最佳匹配设计问题,提出了一种基于随机共振理论的研究方法。首先,文章通过二波耦合过程进行物理机理分析和数值实验分析,证明了该问题在本质上可归结为一种随机共振现象。其次,从随机共振的角度,研究其中的最佳参数设计问题,给出了一种分布处理的最优参数设计流程。按照该方法,在给定增益要求的情况下,先根据信号光饱和与否来确定晶体长度,最后根据非相干光的比例对增益的影响来确定非相干光的比例。仿真实验表明,经过最佳参数设计后,信号的增益和输出信噪比上均有显著提高。     

数值模拟气/气喷嘴速度比对燃烧性能的影响

为研究应用于全流量补燃循环发动机的不同气/气喷嘴得到的燃烧流场,通过求解NavierStokes方程组,对不同燃料与氧化剂速度比下的流动燃烧过程进行了数值计算,计算结果与实验结果吻合。仿真结果表明:增加速度比能使燃烧火焰面提前,燃烧效率变大。如果发动机的长度受到限制,可以适当增加速度比以实现高效燃烧。     

阶比谱分析与汽车起动电机故障的实时诊断

本文主要论述阶比谱分析方法及其在汽车起动电机故障实时诊断中的应用。首先阐述了阶比谱分析的原理以及阶比采样中混迭与泄漏的产生及其抑制方法,然后讨论了如何在起动电机运行过程短、升速快的情况下获取感兴趣的噪声信号,进而采用阶比谱分析方法从信号中提取故障特征信息,最后利用阀值判别法起动电机的故障进行实时诊断。     

Effects of total pressures and equivalence ratios on kerosene/air rotating detonation engines using a paralleling CE/SE method

In this paper, the kerosene/air rotating detonation engines(RDE) are numerically investigated, and the emphasis is laid on the effects of total pressures and equivalence ratios on the operation characteristics of RDE including the initiation, instabilities, and propulsive performance. A hybrid MPI + OpenMP parallel computing model is applied and it is proved to be able to obtain a more effective parallel performance on high performance computing(HPC) systems. A series of cases with the total pressure of 1 MPa, 1.5 MPa, 2 MPa, and the equivalence ratio of 0.9, 1, 1.4 are simulated. On one hand, the total pressure shows a significant impact on the instabilities of rotating detonation waves. The instability phenomenon is observed in cases with low total pressure (1 MPa) and weakened with the increase of the total pressure. The total pressure has a small impact on the detonation wave velocity and the specific impulse. On the other hand, the equivalence ratio shows a negligible influence on the instabilities, while it affects the ignition process and accounts for the detonation velocity deficit. It is more difficult to initiate rotating detonation waves directly in the lean fuel operation condition. Little difference was observed in the thrust with different equivalence ratios of 0.9, 1, and 1.4. The highest specific impulse was obtained in the lean fuel cases, which is around 2700 s. The findings could provide insights into the understanding of the operation characteristics of kerosene/air RDE.     

Research on fuze microswitch based on corona discharge effect

Abnormal voltages such as electrostatic, constant current, and strong electromagnetic signals can erro-neously trigger operation of MEMS pyrotechnics and control systems in a fuze, which may result in casualties. This study designs a solid-state micro-scale switch by combining the corona gas discharge theory of asymmetric electric fields and Peek's Law. The MEMS switch can be transferred from "off" to"on" through the gas breakdown between the corona electrodes. In the model, one of the two electrodes is spherical and the other flat, so a non-uniform electric field is formed around the electrodes. The theoretical work is as follows. First, the relation among the radius of curvature of the spherical electrode, the discharge gap, and the air breakdown voltage is obtained; to meet the low voltage (30-60 V) required to drive the MEMS switch, the radius of curvature of the spherical electrode needs to be 10-50 μm and the discharge gap between the two electrodes needs to be 9-11 μm. Second, the optimal ratio ε is introduced to parameterize the model. Finally, the corona discharge structural parameters are determined by comparing the theoretical and electric field simulation results. The switch is then fabricated via MEMS processing. A hardware test platform is built and the performing chip tested. It is found that when the electrode gap is 9 μm, the electrostatic voltage is at least 37.3 V, with an error of 2.6% between the actual and theoretical air breakdown voltages. When the electrode gap is 11 μm, the electrostatic voltage is at least 42.3 V, with an error of 10.5% between the actual and theoretical air breakdown voltages. Both cases meet the design requirements.