排序方式: 共有60条查询结果,搜索用时 31 毫秒
51.
利用热电偶测试了无电焊接过程中同一厚度钢板不同位置、不同厚度钢板同一位置处的焊接热循环曲线,探讨了无电焊接热循环规律及焊接母材厚度对无电焊接热循环的影响。研究表明:无电焊接时,焊件上不同位置点的热循环曲线与电弧焊基本相似。但相较而言,无电焊接在加热阶段的升温速度与冷却阶段的降温速度均显著小于电弧焊。无电焊接过程中,焊件上离焊缝中心线越近,其升温速度越大,峰值温度越高,冷却速度也越大,这一变化规律与电弧焊时完全一致。无电焊接时,焊接热量沿横向的传热速度远大于其沿纵向的传热速度,这使得焊件厚度对无电焊接的影响较为显著,也是焊件厚度增加将导致焊接难度显著增大的根本原因。 相似文献
52.
介绍了数字伺服系统中用十六位二进制数表示角的方法和误差角的计算。使数字伺服系统设计者从根本上树立角与数关系的正确看法,从而有助于正确、简练地设计控制算法程序。 相似文献
53.
54.
张丽娜 《兵团教育学院学报》2005,15(6):12-14,54
文章以《史记》实录精神与托愤精神组合为突破口,阐述了实录精神、托愤精神的远源和在史文中的凸显,进一步挖掘二者之间相悖的二元性关系,从而揭示《史记》中所蕴含的这种文化悖论本身的深刻性、美感魅力以及难解的文化之谜。 相似文献
55.
异源图像匹配是图像处理领域尚未解决的问题。其中,合成孔径雷达图像与光学图像差异较大,用现有方法匹配通常难以得到满意结果。针对这个问题,提出一种基于Gabor编码的异源图像匹配方法:选取一组Gabor滤波器,分别对大图和小图进行Gabor卷积;采用池化方法对卷积结果进行压缩表示;对池化结果二值化并转换为二进制表示得到Gabor二进制编码特征;采用二进制位操作计算实时图与基准图对应窗口特征的相似性,相似性最大值对应图像匹配结果。本方法采用二进制对图像进行描述,减少了计算量,同时也更好地描述了异源图像间的共性特征。实验结果表明,本方法具有较高的匹配概率,计算时间少于现有方法。 相似文献
56.
In this article, a model for a repairable consecutive‐k‐out‐of‐n: F system with Markov dependence is studied. A binary vector is used to represent the system state. The failure rate of a component in the system depends on the state of the preceding component. The failure risk of a system state is then introduced. On the basis of the failure risk, a priority repair rule is adopted. Then the transition density matrix can be determined, and the analysis of the system reliability can be conducted accordingly. One example each of a linear and a circular system is then studied in detail to explain the model and methodology developed in this paper. © 2000 John Wiley & Sons, Inc. Naval Research Logistics 47: 18–39, 2000 相似文献
57.
Acceptance sampling plans are used to assess the quality of an ongoing production process, in addition to the lot acceptance. In this paper, we consider sampling inspection plans for monitoring the Markov‐dependent production process. We construct sequential plans that satisfy the usual probability requirements at acceptable quality level and rejectable quality level and, in addition, possess the minimum average sample number under semicurtailed inspection. As these plans result in large sample sizes, especially when the serial correlation is high, we suggest new plans called “systematic sampling plans.” The minimum average sample number systematic plans that satisfy the probability requirements are constructed. Our algorithm uses some simple recurrence relations to compute the required acceptance probabilities. The optimal systematic plans require much smaller sample sizes and acceptance numbers, compared to the sequential plans. However, they need larger production runs to make a decision. Tables for choosing appropriate sequential and systematic plans are provided. The problem of selecting the best systematic sampling plan is also addressed. The operating characteristic curves of some of the sequential and the systematic plans are compared, and are observed to be almost identical. © 2001 John Wiley & Sons, Inc. Naval Research Logistics 48: 451–467, 2001 相似文献
58.
传统的高阶BOC信号多径抑制算法的有效收敛区间较小,不利于信号的稳定跟踪,因此提出一种多区域鉴别器的高阶BOC多径抑制算法。在伪码误差为零的附近区域,采用优化的QStrobe多径抑制鉴别器,而在其他区域采用收敛区间较大的正交BOC鉴别器。利用卡尔曼滤波器对跟踪误差进行开环估计,判断误差所处区域并进行鉴别器的实时切换。对BOC(15,2.5)和BOC(14,2)信号的仿真结果表明,该算法能够实现无模糊跟踪,且6 d B衰减多径误差包络面积比传统QStrobe算法分别改善了57%和51%。 相似文献
59.
二元探测传感器网络的递推加权质心目标定位算法 总被引:5,自引:1,他引:4
为进一步降低二元探测传感器网络质心定位算法的计算复杂度和通信量、提高定位精度,推导出一种质心算法的递推公式,使用该递推公式可以大大减少定位的计算、存储和通信量;在递推质心公式的基础上,提出了一种基于节点探测到目标的次数的递推加权质心定位算法,从而提高了定位精度.对递推公式和加权质心算法进行了模拟仿真,结果验证了递推公式和加权递推质心算法的有效性. 相似文献
60.
在现有的RFID标准中,一般标签ID都由几个不同含义区间组成。针对这种特点,提出推断式二进制防碰撞算法:在识别每个区间段的ID时,利用某个特定读写器中的前缀库推断该区间段各个位的取值,以便减少待识别标签ID的位数。同时,通过调整参数u,可以对系统可靠性进行控制。仿真实验表明,在没有新前缀出现的情况下,推断式二进制防碰撞算法能够将QT算法的识别速度提高3倍、标签平均响应次数降低3/4。 相似文献