Experimental investigation on enhanced damage to fuel tanks by reactive projectiles impact

Enhanced damage to the full-filled fuel tank,impacted by the cold pressed and sintered PTFE/AL/W reactive material projectile(RMP)with a density of 7.8 g/cm3,is investigated experimentally and theoretically.The fuel tank is a rectangular structure,welded by six pieces of 2024 aluminum plate with a thickness of 6 mm,and filled with RP-3 aviation kerosene.Experimental results show that the kerosene is ignited by the RMP impact at a velocity above 1062 m/s,and a novel interior ignition phenomenon which is closely related to the rupture effect of the fuel tank is observed.However,the traditional steel projectile with the same mass and dimension requires a velocity up to 1649 m/s to ignite the kerosene.Based on the experimental results,the radial pressure field is considered to be the main reason for the shear failure of weld.For mechanism considerations,the chemical energy released by the RMP enhances the hydrodynamic ram(HRAM)effect and provides additional ignition sources inside the fuel tank,thereby enhancing both rupture and ignition effects.Moreover,to further understand the enhanced ignition effect of RMP,the reactive debris temperature inside the kerosene is analyzed theoretically.The initiated reactive debris with high temperature provides effective interior ignition sources to ignite the kerosene,resulting in the enhanced ignition of the kerosene.     

The deformation and failure mechanism of cylindrical shell and square plate with pre-formed holes under blast loading

The deformation and failure mechanism of cylindrical shells and square plate with pre-formed holes under blast loading were investigated numerically by employing the Ansys 17.0 and Ls-Dyna 971. To calibrate the numerical model, the experiments of square plates with pre-formed circle holes were modeled and the numerical results have a good agreement with the experiment data. The calibrated numerical model was used to study the deformation and failure mechanism of cylindrical shells with pre-formed circle holes subjected to blast loading. The structure response and stress field changing process has been divided into four specific stages and the deformation mechanism has been discussed systematically. The local and global deformation curves, degree of damage, change of stress status and failure modes of cylindrical shell and square plate with pre-formed circular holes are obtained, compared and analyzed, it can be concluded as: (1) The transition of tensile stress fields is due to the geometrical characteristic of pre-formed holes and cylindrical shell with arch configuration; (2) The existence of pre-formed holes not only lead to the increasing of stress concentration around the holes, but also release the stress concentration during whole response process; (3) There are three and two kinds of failure modes for square plate and cylindrical shell with pre-formed holes, respectively. and the standoff distance has a key influence on the forming location of the crack initiating point and the locus of crack propagation; (4) The square plate with pre-formed holes has a better performance than cylindrical shell on blast-resistant capability at a smaller standoff distance, while the influence of pre-formed holes on the reduction of blast-resistant capability of square plate is bigger than that of cylindrical shell.     

群时延傅里叶分解模型及其估计方法

建立了基于三角函数级数的群时延模型,并理论证明了仅采用有限阶数的三角函数群时延即可表征任意群时延对信号相关峰的影响。在此基础上,通过测量信号相关峰,并与不同三角函数群时延组合下的相关峰进行匹配搜索即可估计群时延的三角函数分解级数,从而估计得到相关峰影响等效的群时延特性。仿真中,采用该方法估计得到的群时延特性对滤波器进行修正后,信号相关峰与经过滤波器之前的信号相关峰高度吻合,时延估计偏差在0.1 ns之内。     

浅议行政执法责任制

行政执法责任制是依法行政的重要保障。当前实施行政执法责任制存在着一些问题,应从行政执法责任制的本质和操作规程、依法界定执法职责、建立评议考核机制等三个方面进行改革。     

巡航导弹攻击路径组的优化与评估

为保证对敌方目标实施多次有效攻击,巡航导弹攻击路径选择的关键在于寻找一组优化路径而不是一条优化路径(如果存在),既满足性能指标要求,又满足作战应用要求.在作战区域内任意两个匹配区之间飞行航迹已知(专题讨论)的情况下,就巡航导弹攻击路径组的优化与评估问题进行了探讨,分析了导弹作战运用要求和性能指标要求,建立了攻击路径组的优化与评估模型,计算结果表明:所给出优化与评估模型是可行的,能够满足巡航导弹实际作战要求.     

矿物掺合料对GRC耐久性的影响

通过长达3年的标准养护试验及80℃热水加速老化试验,研究了矿物掺合料粉煤灰、硅灰对耐碱玻璃纤维增强普通硅酸盐水泥(GRC)耐久性的影响,并对矿物掺合料改善GRC耐久性的机理作了初步分析探讨。研究结果表明,粉煤灰和硅灰矿物掺合料可明显改善GRC的长期耐久性。     

防空兵群指挥所配置方案优化分析

防空兵群指挥所配置是兵力部署的重要内容,它从根本上决定了指挥所的指挥效能和野战生存能力。多年来,指挥所的配置多是根据防空兵战斗的相关战术原则,由作战参谋提出数个配置方案,然后由指挥员做出决策。这种仅凭主观决策的做法与现代防空作战的要求不相适应。结合模糊多指标评判方法与优化理论,从发挥指挥效能与提高生存能力两个方面出发,对防空群指挥所的配置进行了分析,并建立了配置方案优化的模型,从根本上改变了指挥所配置完全依赖主观判断的做法。最后应用模型分析了一个实例。     

坦克炮塔方向机不自锁情况分析

59式坦克和62式坦克炮塔方向机,在使用中多次出现过不自锁现象,针对这种情况,从设计上找出了原因,提出了防止不自锁的措施,并对改进的第二代、第三代炮塔方向机自锁情况进行了剖析.     

共址调频和调幅系统干扰机理及干扰抑制需求分析

以调幅和调频电台为研究对象,对共平台接收电台前端低噪声放大器的非线性进行精确建模,分别对调幅电台和调频电台的干扰抑制需求进行解析,并通过数值仿真对解析模型进行验证。结果表明:所提解析模型较现有模型更为准确;当有用信号功率、噪声功率和干扰功率相同时,调幅通信系统的干扰抑制需求高于调频通信系统。     

Analysis of a production system in a general configuration

We consider a production system comprising multiple stations (or workshops) such as an entry station, a set of work stations, a central station, and an exit station, which are arranged in a general configuration. A worker (or a vehicle tool) is assigned to each station, who sends a part from the station to the destination station according to the required process path of the part. Any part is allowed to visit a work station more than once if its process path requires. We propose a new control strategy with the push policy for instructing each worker to send a part and the kanban mechanism for controlling the work‐in‐process (WIP) in each work station. As all work stations have limited local buffers, the central station is used for storing blocked parts temporarily. Such a production system is modeled as an open queueing network in a general configuration with a Markovian part sending policy and a machine no blocking mechanism. The queueing network is analytically characterized. Some important performance measures are compared with other control strategies. A semi‐open decomposition approach is applied to the queueing network for computing the blocking probabilities when parts arrive at the work stations. An algorithm is developed based on the semi‐open decomposition approach. Numerical experiments show the quality of the solutions obtained by the algorithm as well as a property of a performance measure. © 2001 John Wiley & Sons, Inc. Naval Research Logistics 48: 128–143, 2001