空间信息支持高能激光武器应用研究*

依据空间信息支持现代作战的主要内容,介绍了五大类空间信息状况,分析了新概念武器高能激光的基本原理,并就其应用过程建立了UML模型。在此基础上,设计了空间信息支持高能激光武器应用系统的框架,并就高能激光武器对空间信息的需求进行了重点分析,而后以信息的转换与传递为主线,探讨了高能激光武器运用空间信息的流程。最后对该领域研究的趋势和发展前景做出了展望,并提出对其未来发展的要求。     

高层民用建筑电气防火设计

针对高层民用建筑电气防火设计问题，结合现行国家标准的规定进行了探讨，提出了消防电源及其配电、应急照明等设计原则。     

基于数字信道化的极微弱信号载波频率引导模块设计与实现

针对深空探测中常规点数的FFT无法对极微弱信号进行精确的频率引导,而超长点数的FFT无法用现有器件实现,提出一种基于数字信道化的并行FFT频率引导方法.接收信号先经过数字信道化处理,均匀划分为若干窄带信号,然后分别对各子带信号进行FFT运算,最后通过对各子带有效谱线的联合检测完成载波频率的精确估计.在等效219点FFT的频率引导模块FPGA实现中,通过FFT模块的复用节约了硬件资源开销.测试结果表明:在8MHz采样率下该模块的测频精度小于10Hz.     

Effect of tool rotational speed on the particle distribution in friction stir welding of AA6092/17.5 SiCp-T6 composite plates and its consequences on the mechanical property of the joint

This study investigates the effect of tool rotational speed (TRS) on particle distribution in nugget zone (NZ) through quantitative approach and its consequences on the mechanical property of friction stir welded joints of AA6092/17.5 SiC_p-T6 composite. 6 mm thick plates are welded at a constant tool tilt angle of 2° and tool traverse speed of 1 mm/s by varying the TRS at 1000 rpm, 1500 rpm and 2000 rpm with a taper pin profiled tool. Microstructure analysis shows large quantity of uniformly shaped smaller size SiC particle with lower average particle area which are homogeneously distributed in the NZ. The fragmentation of bigger size particles has been observed because of abrading action of the hard tool and resulting shearing effect and severe stress generation due to the rotation of tool. The particles occupy maximum area in the matrix compared to that of the base material (BM) due to the redistribution of broken particles as an effect of TRS. The migration of particles towards the TMAZ-NZ transition zone has been also encountered at higher TRS (2000 rpm). The microhardness analysis depicts variation in average hardness from top to bottom of the NZ, minimum for 1500 rpm and maximum for 2000 rpm. The impact strength at 1000 rpm and 1500 rpm remains close to that of BM (21.6 J) while 2000 rpm shows the accountable reduction. The maximum joint efficiency has been achieved at 1500 rpm (84%) and minimum at 1000 rpm (68%) under tensile loading. Fractographic analysis shows mixed mode of failure for BM, 1000 rpm and 1500 rpm, whereas 2000 rpm shows the brittle mode of failure.     

FeAlCrNbB金属间化合物复合涂层的制备与表征

研究开发了一种FeAlCrNbB新型喷涂粉芯丝材,并结合自动化高速电弧喷涂工艺制备了该材料的复合涂层,分析了涂层的常规力学性能、组织结构和油润滑条件下的滑动摩擦磨损性能,并和常规FeAl涂层进行了对比。结果显示:FeAlCrNbB涂层具有相对较高的显微硬度和拉伸结合强度、低的孔隙率,组织致密,形成了由Fe-Al金属间化合物相、氧化物以及少量非晶和纳米晶组成的复合结构,由于这种复合结构的材料特征,使涂层具备较好的耐磨损性能。