含脉冲负载的综合电力系统储能优化配置研究

考虑到舰船环境限制和高能脉冲负载对储能的需求,有必要对储能装置进行合理的选型和优化配置,来提升综合电力系统性能。为此,基于带权极小模理想点法和层次分析法,提出了一种储能装置性能评价函数,并以其为优化目标,进行储能装置优化配置。所提出的评价函数充分考虑系统需求和脉冲负载特性,以储能装置体积、质量和经济性作为评价函数主要组成部分,同时考虑功率、能量、电压、荷电状态等约束,建立优化配置模型,并采用差分进化算法进行求解。以高性能锂电池和超级电容器为例,对所提模型进行求解计算,结果表明在所给权重系数下锂电池性能更优,更适用于综合电力系统,并给出了优化配置后的指导方案。     

Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Formation of adiabatic shearing band for high-strength Ti-5553 alloy: A dramatic thermoplastic microstructural evolution

By using split Hopkinson pressure bar, optical microscopy and electronic microscopy, we investigate the influence of initial microstructures on the adiabatic shear behavior of high-strength Ti–5Al–5V–5Mo–3Cr (Ti-5553) alloy with lamellar microstructure and bimodal microstructure. Lamellar alloy tends to form adiabatic shearing band (ASB) at low compression strain, while bimodal alloy is considerably ASB-resistant. Comparing with the initial microstructure of Ti-5553 alloy, we find that the microstructure of the ASB changes dramatically. Adiabatic shear of lamellar Ti-5553 alloy not only results in the formation of recrystallized β nano-grains within the ASB, but also leads to the chemical redistribution of the alloying elements such as Al, V, Cr and Mo. As a result, the alloying elements distribute evenly in the ASB. In contrast, the dramatic adiabatic shear of bimodal alloy might give rise to the complete lamination of the globular primary α grain and the equiaxial prior β grain, which is accompanied by the dynamic recrystallization of α lamellae and β lamellae. As a result, ASB of bimodal alloy is composed of α/β nano-multilayers. Chemical redistribution does not occur in ASB of bimodal alloy. Bimodal Ti-5553 alloy should be a promising candidate for high performance armors with high mass efficiency due to the processes high dynamic flow stress and excellent ASB-resistance.     

引入块内码元频数抽样的块内频数检测识别方案

为识别链路层比特流是否加密,以未加密与加密数据在随机统计特性上的差异为依据,利用随机性检测的方法对加密比特流进行识别.在不同比特流长度条件下对3种典型随机性检测方法的识别率进行了比较研究.针对3种检测方法均对长度较短的未加密比特流识别率较低的问题,在块内频数检测的基础上,提出了基于块内码元频数抽样的比特流预处理方案,以及块内频数检测最优分块长度选择方案,并对预处理方案对识别率的影响进行了分析.实验结果表明,提出的方案可以显著提高块内频数检测对未加密比特流的识别率.     

弹道导弹被动段最优脉冲变轨方法

弹道导弹大气层外飞行时间长且弹道固定,易被敌方预测和拦截。针对以上问题,本文提出一种最优脉冲式变轨方法,该方法设计的弹道由2条不同的椭圆弧段组成,成功命中目标的同时,增加了敌方的拦截难度。以机动变轨所需能量和变轨后飞行剩余时间的加权最优为性能指标,设计了利用遗传算法在初始弹道上寻求最优变轨点的方法。最后,将遗传算法搜索最优点结果与遍历搜索结果进行对比,其最大误差为 ,从而验证了遗传算法在应用于导弹变轨问题,用以寻求最优变轨点是准确有效的。     

翼伞精确空投系统归航轨迹规划与控制

翼伞归航轨迹规划与控制问题是翼伞系统在一定初始状态下,利用自身可操作性,完成从初始位置到目标位置的转移问题。针对翼伞空投系统不同归航要求,规划出满足精度要求为圆径概率误差（ CEP ）小于40m的归航轨迹并经过一定量的控制完成翼伞空投系统精确空投任务。首先建立翼伞系统状态空间六自由度模型,并在此基础上提出系统简化稳态模型,通过最优控制方法,规划出满足空投要求的最优归航轨迹后对翼伞进行不断控制直至目标点。最后通过Matlab仿真试验,绘出翼伞系统归航轨迹图与控制变化图。     

基于在线学习的频谱感知次序策略*

认知无线电允许次级用户在频谱没有被主用户使用时动态地接入频谱进行数据传输。动态频谱接入是解决无线电频谱资源短缺和使用效率低下问题的有效方案,而频谱感知是实现动态频谱接入的关键挑战之一。次级用户的感知能力有限,为了快速找到频谱空闲概率最大的频段从而获得更多的频谱接入机会,研究了频谱感知次序问题。考虑到频谱空闲概率会随时间变化且对次级用户不可知,提出了一个在线学习框架,把频谱感知次序问题规约成经典多摇臂赌博机问题,并利用在线学习方法——满意折现汤普森抽样算法(satisficing discounted Thompson sampling)处理优化问题。仿真结果表明,和其他算法相比,所提算法可获得更多的频谱接入机会并且能够跟踪频谱空闲概率的变化。     

纤维缠绕复合材料夹芯圆柱体高应变率压缩吸能机理

为研究纤维缠绕复合材料夹芯圆柱体吸能元件在高应变率冲击压缩载荷作用下的变形损伤模式和能量吸收机理,采用ABAQUS商用有限元软件和分离式Hopkinson压杆装置开展数值模拟分析和试验验证研究。对比分析宏观力学响应规律和微观损伤破坏机理,可知吸能结构元件在高应变率压缩载荷下的力学响应具有典型的弹塑性特征,内部芯材主要产生压缩塑性损伤,而表层复合材料沿环向产生拉伸断裂破坏。研究表明,该吸能元件冲击压缩吸能特性优异,可满足水下结构平台的冲击防护和浮力储备要求。     

Burning rate and other characteristics of strontium titanate (SrTiO3) supplemented AP/HTPB/Al composite propellants

In a quest of search for a new burning rate modifier for composite propellant, strontium titanate (SrTiO₃), a perovskite oxide has been chosen for evaluation in a composite propellant formulation based on its other catalytic applications. Initially, SrTiO₃ was characterized for particle size, morphology and material/phase identification (using XRD). By varying SrTiO₃ content in a standard composite propellant, different compositions were prepared and their performance and processing parameters like the end of mix (EOM) viscosity, mechanical properties, density, burning rate, pressure exponent (n-value), etc. were measured. The results reveal that 2% SrTiO₃ causes more than 12% enhancement in propellant burning rate (at 70 ksc pressure) in comparison to the standard propellant composition. The pressure exponent also increases to 0.46, whereas the standard composition was having its value as 0.35.     

流的大小与传输速率相结合的双门限检测算法

提出基于流传输速率与数据量的双门限检测算法。为满足高速网络传输的性能要求,使用Hash表存储流检测的数据结构,将Hash表的冲突处理与基于流速率的缓存替换相结合以实现高效的大流检测,通过限制Hash桶的容量,确保报文的处理性能。真实网络数据的仿真测试结果表明:所提算法在相近的存储开销下,保持了较高的处理性能,准确性优于基于最近最少使用算法的大流检测及其派生算法以及基于统计计数的紧凑型空间节省算法。