Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Analysis on damage characteristics and detonation performance of solid rocket engine charge subjected to jet

To further explore the damage characteristics and impact response of the shaped charge to the solid rocket engine (SRE) in storage or transportation, protective armor was designed and the shelled charges model (SCM)/SRE with protective armor impacting by shaped charge tests were conducted. Air overpressures at 5 locations and axial acceleration caused by the explosion were measured, and the experimental results were compared with two air overpressure curves of propellant detonation obtained by related scholars. Afterwards, the finite element software AUTODYN was used to simulate the SCM impacted process and SRE detonation results. The penetration process and the formation cause of damage were analyzed. The detonation performance of TNT, reference propellant, and the propellant used in this experiment was compared. The axial acceleration caused by the explosion was also analyzed. By comprehensive comparison, the energy released by the detonation of this propellant is larger, and the HMX or Al particles contained in this propellant are more than the reference propellant, with a TNT equivalent of 1.168–1.196. Finally, advanced protection armor suggestions were proposed based on the theory of woven fabric rubber composite armor (WFRCA).     

节点非独立失效下的局域网可靠性建模与分析

以具有层次结构的局域网作为拓扑模型,考虑共因失效和关联失效这2类节点非独立失效事件发生的情况,建立了交换机节点失效模型来模拟交换机失效,利用Monte-Carlo仿真算法近似计算出网络的两端可靠性,研究2种共因失效事件和3种关联失效事件对网络端端可靠性的影响。结果表明:因资源节点出现故障和协议层出现错误而导致交换机失效的共因失效事件均会降低网络可靠性,且资源节点失效概率或协议层失效概率越大,网络可靠性越低;而由于使用了热备份技术、堆叠技术以及发生广播风暴导致的关联失效事件,即使节点独立失效概率很小,只要相关因数足够大,故障都会快速传播,导致网络可靠性迅速下降。     

钢丝增强复合条带抗弹性能数值分析

为研究钢丝增强聚合物基复合条带的抗弹性能,基于冲击动力学理论分析其抗弹机理,再借助ANSYS/LS-DYNA软件和LS-PrePost前后处理器模拟有无增强钢丝2种工况下,条带对7.62 mm弹体的冲击响应。分析表明：条带的弹性模量、剪切模量和面密度会影响其能量吸收性能,能量吸收量随三者的增大而增大;由于聚合物基体的正交各向异性,应力云图显示出扁平椭圆状是合理的;在聚合物基复合条带中嵌入增强钢丝对条带整体的抗弹性能有积极的影响,但嵌入过量的钢丝会导致重量和成本的增加,因此需要对合理的钢丝配比率作进一步研究。研究结果可为钢丝增强聚合物基复合条带在野战防护结构中的应用提供参考。     

基于Monte Carlo的军事物流结点可靠性评估方法

军事物流网络结点是构成军事物流网络的基本要素。战场环境瞬息万变,结点的可靠性往往受许多不确定因素的影响,计及不确定因素的评估方法可以更客观、真实地评估结点的可靠性。基于此,提出了刻画物流结点可靠性的评估指标体系,建立了计及不确定因素的军事物流结点可靠性评估模型,给出了Monte Carlo求解算法。对影响结点可靠性的因素进行了分析,在此基础上提出了改善军事物流结点可靠性的措施。以某战役级军事物流网络为例进行算例分析,验证了该方法的可行性和正确性。     

作战飞机可靠性与维修性仿真模型

通过故障树分析建立了作战飞机仿真逻辑关系。在修正线性同余法的基础上获得了随机数模型。在各设备故障发生状态和修复状态识别的基础上,建立了可靠性维修性仿真模型,确定了作战飞机在仿真过程中的工作状态,并根据故障模式影响分析预计了设备故障对作战飞机的影响。最后以F/A-18为例进行可靠性维修性仿真,获得了实时的故障信息和修复信息,验证了仿真模型的可行性。     

二维拉格朗日和欧拉结合法在流处理器MASA上的实现与评测

现代半导体工艺技术的发展使得在单芯片上放置数百个运算单元成为可能,但是全局片上片外带宽受限。通用处理器体系结构不能较好地适应变化,仍然依靠全局片上结构,少量的运算单元。而流体系结构拥有大量的运算单元、鲜明的存储层次,使得在有限的片外带宽下,用高的本地带宽来满足大量运算单元的需求。首先介绍了原型MASA流体系结构,然后给出了爆轰流体力学中的二维拉格朗日和欧拉结合法(Ygx2)在流体系结构上实现的实例研究,最后用时钟精确的模拟器来评测应用的运行性能,结果表明Ygx2应用在500MHz的MASA上运行结果与1.6GHz的Iantium2的比较快近4倍,证实了流体系结构在高性能计算领域的极大潜力。     

液体火箭发动机无失效条件下的可靠性分析方法

针对液体火箭发动机热试车过程中可能出现的无失效情况,在对寿命分布进行分析的基础上,利用配分布曲线-最小二乘法,采用经典估计和Bayes估计作为先验分布,对液体火箭发动机无失效条件下的可靠性进行了评估,并对评估结果进行了分析。计算结果表明,采用最小二乘法结合Bayes估计,可以较好评估液体火箭发动机在无失效条件下的可靠性。     

军用软件的测试与实践方法

首先分析了民用软件存在的问题,然后结合军用软件的特点,对影响军用软件可靠性的因素进行分析,最后提出提高军用软件质量的几种测试与实践方法.     

火灾事故与民事侵权责任研究

火灾事故会给受害人造成人身和财产损失,存在民事责任。探讨了火灾事故民事侵权责任,从法律的角度论述了火灾事故民事侵权责任的追究和赔偿,并从建立和完善损害赔偿专家证人制度及火灾保险制度提出了完善火灾民事赔偿制度的建议。