Life in the “Gray Zone”: observations for contemporary strategists

The term “Gray Zone” is gaining in popularity as a way of describing contemporary security challenges. This article describes the “short-of-war” strategies – the fait accompli, proxy warfare, and the exploitation of ambiguous deterrence situations, i.e. “salami tactics” – that are captured by the term and offers several explanations for why state and non-state actors are drawn to these strategies. The analysis highlights why defense postures based on deterrence are especially vulnerable to the short-of-war strategies that populate the “Gray Zone.” The article concludes by suggesting how defense officials might adapt defense policies to life in the “Gray Zone.”     

激光陀螺数字抖动控制方法与特性

针对传统的模拟抖动控制系统体积大、灵活性差的缺点,设计了一种基于单片机的新的激光陀螺数字抖动控制方法,建立了陀螺抖动的数学模型,比较研究了传统的模拟正弦波驱动和新的数字方波驱动的抖动特性,指出了后者不同于前者的抖幅变化律及非线性的随机噪声注入方式。仿真和实验证明,该方法能很好满足激光陀螺抖动控制要求,保证陀螺性能。     

采用局域像素匹配的随机抽样一致改进算法

为提高图像拼接的配准精度和稳健性,提出基于局域像素匹配的随机抽样一致改进算法。在完成尺度不变特征变换算子或其他算子图像特征提取、特征匹配之后,利用独立于特征匹配点的局域像素,通过参考图像局域像素与映射的待拼接图像局域像素匹配,优选4对最佳特征匹配点,确定最佳单应矩阵。实验结果表明:与随机抽样一致经典算法相比,该方法未明显增加计算耗时,单应矩阵更准确,图像拼接稳健性更好。     

88B坦克分队与M60A3坦克分队随机火力对抗

以 8 8 B坦克分队进攻防御阵地之 M6 0 A3坦克分队为立足点 ,建立双方随机对抗时的兰彻斯特平方律模型 ,结合战场实际 ,得出 88B坦克分队取得最大作战效能时的最佳兵力比 ,及其运用火力的几点结论。     

自修复飞控系统故障检测与隔离软件系统

介绍了一个自修复飞行控制系统故障检测和隔离实时工程软件系统,该系统按照软件工程规范、采用等价空间法和残差向量的概率信息融合法研制和开发,不仅能对飞行控制系统的突变故障——作动器卡死故障和控制舵面损伤故障进行实时检测和隔离,而且具有良好的用户界面。仿真研究表明该软件系统具有良好的鲁棒性和实时性。     

A comparative study of three tool replacement/operation sequencing strategies in a flexible manufacturing system

This paper studies three tool replacement/operation sequencing strategies for a flexible manufacturing system over a finite time horizon: (1) failure replacement—replace the tool only upon failure, (2) optimal preventive tool replacement for a fixed sequence of operations, and (3) joint scheduling of the optimal preventive tool replacement times and the optimal sequence of operations. Stochastic dynamic decision models are used for strategies 2 and 3. The optimization criterion for strategies 2 and 3 is the minimization of the total expected cost over the finite time horizon. We will show through numerical studies that, with the same amount of information, the total expected costs can be reduced considerably by choosing an optimal strategy. Our conclusion is that in flexible manufacturing, optimal tool replacement and optimal operations sequencing are not separate issues. They should be considered jointly to minimize the expected total cost. © 2000 John Wiley & Sons, Inc. Naval Research Logistics 47: 479–499, 2000     

基于小波的信噪分离方法

本文在 Ｄｏｎｏｈｏ 提出的从噪声中恢复信号的非线性小波方法的基本原理的基础上, 并针对非线性小波方法的核心问题——浮动阈值的设定提出了新的算法。通过算例证明, 所设计的浮动阈值在实际应用中效果较好, 特别在低信噪比时信号恢复效果明显优于现常用的浮动阈值设计方法。     

陀螺随机漂移误差模型建模方法研究

论述了自60年代以来的几种主要陀螺仪漂移误差模型建模的方法,介绍了各种方法的特点及建模公式,有助于惯导系统中陀螺漂移误差模型的建立．     

BP神经网络的收敛问题

研究了BP神经网络的收敛问题。基于随机理论 ,提出了解决网络收敛性问题的随机优选法。该方法不仅在任何条件下都能得到问题的具有一定精度的解答 ,而且收敛速度很快     

弯曲载荷作用下复合材料T型接头的失效分析

运用蔡-吴逐步失效判据和黏聚接触模型建立弯曲加载下的T型接头的有限元模型。对复合材料T型接头在弯曲加载下的损伤机理和承载能力进行数值模拟。结合静态弯曲加载实验,揭示T型接头在弯曲破坏过程中的四种失效模式。T型接头的弯曲失效载荷的有限元模型计算结果与实测值吻合较好。