基于空域相关滤波的雷达回波信号降噪方法

对雷达探测来说,如何有效地增强真实目标回波信号、提高信噪比水平是非常重要的。传统的降噪方法如平滑滤波、傅立叶降噪很难有效地降低与目标频谱相重叠的噪声。空域相关滤波算法是小波滤波算法中的一种,能够有效地解决这个问题。该算法是利用真实信号与噪声在尺度间的不同表现来实现的,能够在保留信号细节的同时,有效地降低噪声。仿真表明,该算法在雷达回波的降噪中取得了较好效果,有效地降低了噪声。     

柔性长鳍扭波推进数学模型分析

以"尼罗河魔鬼"鱼的柔性长背鳍扭波推进模式为研究对象,通过观察活鱼的游动模式,提取影响扭波推进的运动学要素,建立了描述柔性长背鳍扭波推进时动态曲面的数学模型。研究了鳍条仰角与摆动规律对鳍面的影响。最后,用细长体理论分析并计算出推力分布。研究表明,鳍条仰角在φ=85°的情况下所形成的鳍面与垂直鳍条所形成的鳍面相比,其最大偏离值与鳍长之比为1.7%,可以用垂直于基线的鳍条制作模型;鳍条按正弦规律摆动时所形成的扭波波形鳍面与实鱼鳍面相似。     

面内阶跃载荷下薄板弹性动力屈曲差分解

根据薄板微元的动力平衡分析导出薄板动力屈曲控制方程,由屈曲瞬间能量转换率守恒条件得出一个压缩波前屈曲变形的附加约束方程,由此得到求解薄板动力屈曲问题的完备定解条件.以受载边夹支的薄板为倒,利用有限差分法得出了薄板前三阶动力屈曲模态和相应的两个特征参数值,并对比分析了薄板静、动力屈曲的差别.分析表明,薄板动力屈曲过程中产生屈曲动能,比静力屈曲要吸收更多的外部能量.     

锥形液膜的Kelvin-Helmholtz扰动波

为进行锥形液膜雾化过程分析,研究锥形液膜的Kelvin-Helmholtz稳定性问题,应用小扰动假设,建立了锥形液膜数学模型、轴对称扰动运动的控制方程和边界条件,采用分离变量法求解线性偏微分扰动方程组,经过严格的数学推导,得到了锥形液膜内外表面扰动波增长速率特征方程.当液膜锥角为零时,与环形液膜扰动波特征方程一致;当液膜锥角和液膜内径为零时,与圆射流扰动波特征方程一致,表明导出的锥形液膜扰波动方程是合理的.     

Modeling of the whole process of shock wave overpressure of free-field air explosion

The waveform of the explosion shock wave under free-field air explosion is an extremely complex problem. It is generally considered that the waveform consists of overpressure peak, positive pressure zone and negative pressure zone. Most of current practice usually considers only the positive pressure. Many empirical relations are available to predict overpressure peak, the positive pressure action time and pressure decay law. However, there are few models that can predict the whole waveform. The whole process of explosion shock wave overpressure, which was expressed as the product of the three factor functions of peak, attenuation and oscillation, was proposed in the present work. According to the principle of explosion similarity, the scaled parameters were introduced and the empirical formula was absorbed to form a mathematical model of shock wave overpressure. Parametric numerical simulations of free-field air explosions were conducted. By experimental verification of the AUTODYN numerical method and comparing the analytical and simulated curves, the model is proved to be accurate to calculate the shock wave overpressure under free-field air explosion. In addition, through the model the shock wave overpressure at different time and distance can be displayed in three dimensions. The model makes the time needed for theoretical calculation much less than that for numerical simulation.     

A fast-running method for blast load prediction shielding by a protective barrier

This study presents a simplified blast load prediction method on structures behind a protective barrier. The proposed method is basically an empirical approach based on Kingery-Bulamsh (K-B) chart and finite element (FE) analysis results. To this end, this study divides the structure into three regions by three critical points. Blast loads at each critical point can be calculated based on K-B chart and an approximation according to FE analysis results. Finally, peak reflected overpressure and impulse distributed on the structure can be approximately estimated by linearly connecting blast loads at each critical point. In order to confirm a feasibility of the proposed method, a series of numerical simulations were carried out. The simulation results were compared with FE analysis results which are presented in the open literature. From such comparisons, it was found that the proposed method is applicable to predict blast loads on structures behind a protective barrier.     

Experimental study of transient pressure wave in the behind armor blunt trauma induced by different rifle bullets

Pressure wave plays an important role in the occurrence of behind armor blunt trauma (BABT), and ballistic gelatin is widely used as a surrogate of biological tissue in the research of BABT. Comparison of pressure wave in the gelatin behind armor for different rifle bullets is lacking. The aim of this study was to observe dynamic changes in pressure wave induced by ballistic blunt impact on the armored gelatin block and to compare the effects of bullet type on the parameters of the transient pressure wave. The gelatin blocks protected with National Institute of Justice (NIJ) class III bulletproof armor were shot by three types of rifle bullet with the same level of impact energy. The transient pressure signals at five locations were recorded with pressure sensors and three parameters (maximum pressure, maximum pressure impulse, and the duration of the first positive phase) were determined and discussed. The results indicated that the waveform and the twin peak of transient pressure wave were not related to the bullet type. However, the values of pressure wave’s parameters were significantly affected by bullet type. Additionally, the attenuation of pressure amplitude followed the similar law for the three ammunitions. These findings may be helpful to get some insight in the BABT and improve the structure design of bullet.     

浅海舰船地震波场仿真中的边界处理

为解决舰船地震波场数值仿真中的边界反射问题,结合浅海传播环境特征和舰船地震波激发机理,提出边界处理算法。采用交错网格有限差分法对一阶速度-应力方程进行数值离散;采用应力镜像法处理海水和空气的自由表面,采用分裂式完全匹配层法处理区域边界;将该模型应用于平行海底近场、远场以及倾斜海底的波场仿真算例中。仿真结果表明:加入边界处理后,自由表面的吸收和区域边界的反射有效减少,波场特征清晰,该算法符合浅海舰船地震波场数值仿真的边界处理要求。     

毫米波合成孔径雷达成像技术

毫米波合成孔径雷达(SAR:Synthetic Aperture Radar)成像技术是雷达技术、现代电子技术和数字信号处理技术的有机结合,使系统雷达的功能发生了质的飞跃.随着SAR成像处理技术的发展,其成像质量不断提高,成为当今高科技条件下一种不可取代的探测、侦察手段,在军事、经济和科学研究等方面都有重大价值和广泛应用前景.主要介绍了毫米波成像雷达与微波雷达相比具有的技术特点,较详细地讨论了毫米波合成孔径雷达的成像原理技术.     

短波差分跳频系统抗干扰性能分析

在阐述短波差分跳频原理的基础上,针对不同的干扰样式:跟踪式干扰、多径干扰、部分频带干扰、单频瞄准式干扰,分别对短波差分跳频系统的抗干扰能力进行具体分析,得出了短波差分跳频系统对抗各种干扰的相关结论,并提出相应增效措施,对深入研究差分跳频系统有重要的意义。