Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Formation of adiabatic shearing band for high-strength Ti-5553 alloy: A dramatic thermoplastic microstructural evolution

By using split Hopkinson pressure bar, optical microscopy and electronic microscopy, we investigate the influence of initial microstructures on the adiabatic shear behavior of high-strength Ti–5Al–5V–5Mo–3Cr (Ti-5553) alloy with lamellar microstructure and bimodal microstructure. Lamellar alloy tends to form adiabatic shearing band (ASB) at low compression strain, while bimodal alloy is considerably ASB-resistant. Comparing with the initial microstructure of Ti-5553 alloy, we find that the microstructure of the ASB changes dramatically. Adiabatic shear of lamellar Ti-5553 alloy not only results in the formation of recrystallized β nano-grains within the ASB, but also leads to the chemical redistribution of the alloying elements such as Al, V, Cr and Mo. As a result, the alloying elements distribute evenly in the ASB. In contrast, the dramatic adiabatic shear of bimodal alloy might give rise to the complete lamination of the globular primary α grain and the equiaxial prior β grain, which is accompanied by the dynamic recrystallization of α lamellae and β lamellae. As a result, ASB of bimodal alloy is composed of α/β nano-multilayers. Chemical redistribution does not occur in ASB of bimodal alloy. Bimodal Ti-5553 alloy should be a promising candidate for high performance armors with high mass efficiency due to the processes high dynamic flow stress and excellent ASB-resistance.     

纤维缠绕复合材料夹芯圆柱体高应变率压缩吸能机理

为研究纤维缠绕复合材料夹芯圆柱体吸能元件在高应变率冲击压缩载荷作用下的变形损伤模式和能量吸收机理,采用ABAQUS商用有限元软件和分离式Hopkinson压杆装置开展数值模拟分析和试验验证研究。对比分析宏观力学响应规律和微观损伤破坏机理,可知吸能结构元件在高应变率压缩载荷下的力学响应具有典型的弹塑性特征,内部芯材主要产生压缩塑性损伤,而表层复合材料沿环向产生拉伸断裂破坏。研究表明,该吸能元件冲击压缩吸能特性优异,可满足水下结构平台的冲击防护和浮力储备要求。     

流的大小与传输速率相结合的双门限检测算法

提出基于流传输速率与数据量的双门限检测算法。为满足高速网络传输的性能要求,使用Hash表存储流检测的数据结构,将Hash表的冲突处理与基于流速率的缓存替换相结合以实现高效的大流检测,通过限制Hash桶的容量,确保报文的处理性能。真实网络数据的仿真测试结果表明:所提算法在相近的存储开销下,保持了较高的处理性能,准确性优于基于最近最少使用算法的大流检测及其派生算法以及基于统计计数的紧凑型空间节省算法。     

靴形喷油速率耦合预喷射对超高压共轨柴油机性能的影响

在介绍超高压共轨系统工作原理的基础上,基于GT-Power软件建立单缸超高压共轨柴油机的仿真模型,并利用试验验证模型的准确性,而后通过模型分析不同喷油速率、靴形喷油速率耦合不同预喷油量和靴形喷油速率耦合不同预喷提前角对超高压共轨柴油机动力性、经济性以及燃烧排放特性的影响。结果表明:通过调整超高压共轨系统中电控增压器电磁阀和喷油器电磁阀的开启时间,能够实现喷油速率的柔性可调。随着喷油速率从矩形变化到靴形,柴油机缸内压力、温度以及NO_x排放量均逐渐降低,而soot排放量逐渐升高,且靴形喷油速率可使柴油机获得最大的功率(扭矩)和最低的油耗率。靴形喷油速率耦合较小的预喷油量可以使柴油机获得更好的动力性、经济性和燃烧特性,但同时也会导致NO_x排放量的升高。靴形喷油速率耦合较大的预喷提前角有助于改善柴油机排放特性,但受到预喷油量的限制,效果并不明显。     

Burning rate and other characteristics of strontium titanate (SrTiO3) supplemented AP/HTPB/Al composite propellants

In a quest of search for a new burning rate modifier for composite propellant, strontium titanate (SrTiO₃), a perovskite oxide has been chosen for evaluation in a composite propellant formulation based on its other catalytic applications. Initially, SrTiO₃ was characterized for particle size, morphology and material/phase identification (using XRD). By varying SrTiO₃ content in a standard composite propellant, different compositions were prepared and their performance and processing parameters like the end of mix (EOM) viscosity, mechanical properties, density, burning rate, pressure exponent (n-value), etc. were measured. The results reveal that 2% SrTiO₃ causes more than 12% enhancement in propellant burning rate (at 70 ksc pressure) in comparison to the standard propellant composition. The pressure exponent also increases to 0.46, whereas the standard composition was having its value as 0.35.     

装备维修中备件需求率的预计方法

通过研究装备维修过程中器件的固有可靠性和维修性,着重分析了影响维修器件需求率的主要因素.利用系统建模和仿真的方法,分别针对耗损类型器件和可修复类型器件建立了相应的需求数学模型,最后给出了维修备件需求率的预计方法.     

速率陀螺解相遇与敌我态势的关系

根据敌我相对运动的原理,导出速率陀螺测量出的目标俯仰角速度Ω_s、测向角速度Ω_L 和探测器测出的距变率与敌我姿势要素间的关系,提出了距变率在极短时间内保持不变的条件;并利用Ω_s、Ω_L 和有关数据(qw,ε、D、■、V_w、K_w)推导出在不满足“快解”条件时计算目标运动要素和弹丸发射诸元的计算公式。     

高速核在高温热平衡等离子体中的非平衡弛豫过程对热核反应率参数的影响

高速核入射到高温热平衡等离子体背景中,由于入射核动能远大于背景等离体中带电粒子之平均动能,入射核在与背景等离子体达到热平衡之前,会存在一段逐渐损失能量的非平衡弛豫过程。本文以高速氘核入射到高温氘化锂等离子体为例,在计及氘核的这种非平衡弛豫过程时,给出了一种计算热核反应D(t,n)~4He之反应率参数的方法。氘核在弛豫过程中的能量损失考虑了氘核与各种带电粒子的库仑散射过程,其能量损失率采用快速带电粒子的慢化理论来计算;氘与背景等离子体中的原子核发生的核反应过程,考虑了非平衡状态下束靶机制的D(t,n)~4He反应和热平衡状态下的D(t.n)~4He反应。在暂未考虑核散射的情况下,计算结果表明,当等离子体温度在7.5KeV～20KeV范围内变化时,氘核的非平衡弛豫过程对热平衡状态下D(t,n)~4He反应率参数的修正因子大致在1.0062～1.0943范围内变动,且温度越高,修正因子越小。计算还表明,当温度一定时,修正因子随等离子体中粒子的数密度变化不明显。     

自适应均衡器非维纳效应的仿真研究

窄带干扰条件下,自适应滤波器产生非维纳效应。在分析非维纳效应产生机理的基础上,详细仿真研究了强单音干扰条件下,自适应均衡器的收敛和跟踪性能。通过研究得出了一些新的结论:多径和干扰的功率严重影响自适应均衡器的收敛速度,而干扰的频率对收敛速度几乎没有影响;固定的强单音干扰对自适应滤波器的信道跟踪性能影响较小;慢变的强单音干扰对跟踪性能影响较小,快变的单音干扰将对跟踪性能造成严重影响。