Burning rate and other characteristics of strontium titanate (SrTiO3) supplemented AP/HTPB/Al composite propellants

In a quest of search for a new burning rate modifier for composite propellant, strontium titanate (SrTiO₃), a perovskite oxide has been chosen for evaluation in a composite propellant formulation based on its other catalytic applications. Initially, SrTiO₃ was characterized for particle size, morphology and material/phase identification (using XRD). By varying SrTiO₃ content in a standard composite propellant, different compositions were prepared and their performance and processing parameters like the end of mix (EOM) viscosity, mechanical properties, density, burning rate, pressure exponent (n-value), etc. were measured. The results reveal that 2% SrTiO₃ causes more than 12% enhancement in propellant burning rate (at 70 ksc pressure) in comparison to the standard propellant composition. The pressure exponent also increases to 0.46, whereas the standard composition was having its value as 0.35.     

进气道角度对含硼推进剂固冲发动机性能的影响

为了提高含硼推进剂固体火箭冲压发动机内硼颗粒的燃烧效率,采用颗粒轨道模型进行了补燃室两相流的数值模拟,其中硼颗粒的点火和燃烧模型采用的是King模型,建立了发动机补燃室内简单反应流模型,在该模型下研究了进气道的位置对非壅塞固体火箭冲压发动机燃烧效率的影响,并在此基础上进行直连式试验研究.结果表明,后进气道角度为60°时的燃烧效率比90°时高.     

H2O2/HTPB固液混合发动机点火试验研究

利用H2O2催化分解原理,设计了烃类燃料在催化分解的90%H2O2中能燃烧的点火器,然后采用该点火器进行H2O2/HTPB固液混合发动机点火试验研究.试验结果表明,该点火器能够成功启动H2O2/HTPB固液混合发动机,且当混合比偏离最佳混合比后,发动机的燃烧效率降低.     

水解法测定发射药钝感剂浓度分布实验条件优化

对水解法测定发射药中钝感剂浓度分布实验条件进行了优化。结果表明,包覆材料选用氯丁橡胶胶粘剂效果最好;水解在沸碱液中进行时,残药表面光滑且能提高测试效率;残药干燥条件为:在100℃干燥20 m in。     

液体推进剂消耗对大型卫星结构动特性的影响分析

为了研究液体推进剂消耗对某大型卫星结构动特性的影响,采用简化的“弹簧-质量”模型分析了推进剂消耗对结构动特性的影响趋势;基于MSC.PATRAN/NASTRAN给出了动力学分析过程中液体推进剂的等效建模和分析方法,包括梁单元法、附加质量法、“RBE3 -质量点”单元法和虚拟质量法等;建立了该卫星结构的有限元模型,进行了结构动力学特性和动响应分析,讨论了液体推进剂消耗对其动特性的影响规律.研究结果表明:随着推进剂的消耗,卫星整体振型的固有频率逐渐增大,而部分局部振型的固有频率保持不变;随着推进剂的消耗,卫星仪器安装板动力学响应峰值逐渐增大,所对应的频率也逐渐增大.     

Analysis on damage characteristics and detonation performance of solid rocket engine charge subjected to jet

To further explore the damage characteristics and impact response of the shaped charge to the solid rocket engine (SRE) in storage or transportation, protective armor was designed and the shelled charges model (SCM)/SRE with protective armor impacting by shaped charge tests were conducted. Air overpressures at 5 locations and axial acceleration caused by the explosion were measured, and the experimental results were compared with two air overpressure curves of propellant detonation obtained by related scholars. Afterwards, the finite element software AUTODYN was used to simulate the SCM impacted process and SRE detonation results. The penetration process and the formation cause of damage were analyzed. The detonation performance of TNT, reference propellant, and the propellant used in this experiment was compared. The axial acceleration caused by the explosion was also analyzed. By comprehensive comparison, the energy released by the detonation of this propellant is larger, and the HMX or Al particles contained in this propellant are more than the reference propellant, with a TNT equivalent of 1.168–1.196. Finally, advanced protection armor suggestions were proposed based on the theory of woven fabric rubber composite armor (WFRCA).     

Deconsolidation and combustion performance of thermally consolidated propellants deterred by multi-layers coating

Both heating and solvent-spray methods are used to consolidate the standard grains of double-base oblate sphere propellants plasticized with triethyleneglycol dinitrate (TEGDN) (TEGDN propellants) to high density propellants. The obtained consolidated propellants are deterred and coated with the slow burning multi-layer coating. The maximum compaction density of deterred and coated consolidated propellants can reach up to 1.39 g/cm³. Their mechanic, deconsolidation and combustion performances are tested by the materials test machine, interrupted burning set-up and closed vessel, respectively. The static compression strength of consolidated propellants deterred by multi-layer coating increases significantly to 18 MPa, indicating that they can be applied in most circumstances of charge service. And the samples are easy to deconsolidate in the interrupted burning test. Furthermore, the closed bomb burning curves of the samples indicate a two-stage combustion phenomenon under the condition of certain thickness of coated multi-layers. After the outer deterred multi-layer coating of consolidated samples is finished burning, the inner consolidated propellants continue to burn and breakup into aggregates and grains. The high burning progressivity can be carefully obtained by the smart control of deconsolidation process and duration of consolidated propellants. The preliminary results of consolidated propellants show that a rapid deconsolidation process at higher deconsolidation pressure is presented in the dynamic vivacity curves of closed bomb test. Higher density and higher macro progressivity of consolidated propellants can be obtained by the techniques in this paper.     

液体火箭发动机故障诊断的最优回归方法

提出了一种基于最优回归理论的液体火箭发动机故障诊断方法，可以在测量参数较少的情况下诊断出较多的发动机故障。当发动机故障不太严重、故障因素也不多时，得到比较满意的关于故障定位和故障大小的结果；在发动机故障比较严重的情况下，仍能得到比较好的故障定位结果；当存在多个故障因素时，诊断效能有所下降。结果表明本文所提方法在比较大的范围之内具有良好的效果。     

溶胶一凝胶法制备二氧化钛及其转化为氮化钛的研究

本文以钛酸丁酯为原料，通过溶胶一凝胶法制备了ＴｉＯ２凝胶，在高温下烧结此凝胶得到ＴｉＯ２。将ＴｉＯ２粉末在９００°Ｃ以上用氨进行氮化，制得金黄色的氮化钛。通过使用热分析、色谱分析、扫描电镜及Ｘ一射线衍射等手段，研究并揭示了凝胶在陶瓷化生成ＴｉＯ２的过程中的化学反应，结晶及晶型随温度的变化规律。发现了氮化钛陶瓷的生成率与ＴｉＯ２溶胶的制备条件之间的关系。     

具有离解反应的推进剂高压蒸发理论探讨

文中提出了具有液相离解反应的推进剂液滴高压蒸发模型,同时还考虑了燃气中极性气体成份对液滴蒸发的影响,并以N_2O_4推进剂液滴为例分析了具有液相离解反应的推进剂蒸发规律。结果表明,此类推进剂高压蒸发并不服从非液相离解反应推进剂的t_b～(?)。规律。模型的提出为液体火箭发动机燃烧室燃烧过程分析提供了新的液滴蒸发理论数据和计算方法。