共查询到2条相似文献,搜索用时 15 毫秒
1.
《防务技术》2020,16(3):588-595
3D-Honeycombed CL-20 structures with low critical size of detonation have been fabricated successfully for intelligent weapon systems using a micro-flow direct ink writing (DIW) technology. The CL-20-based explosive ink for DIW technology was prepared by a two-component adhesive system with waterborne polyurethane (WPU) and ethyl cellulose (EC). Not only the preparation of the explosive ink but also the principle of DIW process have been investigated systematically. The explosive ink displayed strong shear-thinning behavior that permitted layer-by-layer deposition from a fine nozzle onto a substrate to produce complex shapes. The EC content was varied to alter the pore structure distribution and rheological behavior of ink samples after curing. The deposited explosive composite materials are of a honeycombed structure with high porosity, and the pore size distribution increases with the increase of EC content. No phase change was observed during the preparation process. Both WPU and EC show good compatibility with CL-20 particles. Apparently high activation energy was realized in the CL-20-based composite ink compared with that of the refined CL-20 due to the presence of non-energetic but stable WPU. The detonation performance of the composite materials can be precisely controlled by an adjustment in the content of binders. The 3D honeycombed CL-20 structures, which are fabricated by DIW technology, have a very small critical detonation size of less than 69 μm, as demonstrated by wedge shaped charge test. The ink can be used to create 3D structures with complex geometries not possible with traditional manufacturing techniques, which presents a bright future for the development of intelligent weapon systems. 相似文献
2.
Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0%to 15%,every 5%increase of aluminum resulted in about a 1.3%decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14%and 8%higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12%and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80%of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives. 相似文献