T300和JC2#纤维增强C/SiC复合材料力学性能对比

以聚碳硅烷(PCS)为先驱体,采用聚合物浸渍裂解法(PIP)分别制备得到T300碳纤维和JC2#碳纤维增强C/SiC复合材料。JC2#C/SiC复合材料具有优异的力学性能,抗弯强度和断裂韧性分别达到662MPa和19.5MPa.m1/2;T300 C/SiC复合材料表现出低强度、高脆性,其抗弯强度和断裂韧性不足前者的四分之一。T300 C/SiC复合材料低性能的根本原因在于T300纤维在PCS裂解过程中性能严重下降,复合材料中纤维与基体间存在强界面结合是另一个影响因素。     

世界上顶尖的材料与设备技术在哪些国家

<正>全球碳纤维材料碳纤维在高端军事、工业、生活、汽车、飞机等都离不开。碳纤维技术基本被日本东丽、东邦、三菱丽阳垄断,目前中国T800还不能完美量产,东丽目前已经在玩T1100G了。波音、空客是东丽的常客。继碳纤维之后,源自日本的新材料SIC纤维将又一次推动世界技术革新,新一代飞机的发动机核心零部件将采用日本开发的新材料。     

FeAlCrNbB金属间化合物复合涂层的制备与表征

研究开发了一种FeAlCrNbB新型喷涂粉芯丝材,并结合自动化高速电弧喷涂工艺制备了该材料的复合涂层,分析了涂层的常规力学性能、组织结构和油润滑条件下的滑动摩擦磨损性能,并和常规FeAl涂层进行了对比。结果显示:FeAlCrNbB涂层具有相对较高的显微硬度和拉伸结合强度、低的孔隙率,组织致密,形成了由Fe-Al金属间化合物相、氧化物以及少量非晶和纳米晶组成的复合结构,由于这种复合结构的材料特征,使涂层具备较好的耐磨损性能。     

高温空气下C/SiC复合材料力学性能测试

测试了C/SiC复合材料在高温空气下的压缩、弯曲和拉伸性能,利用扫描电子显微镜分析复合材料在室温与高温条件下的断口微观形貌。结果表明:从室温升温到1 000 ℃测试温度时,C/SiC复合材料的压缩强度由247 MPa降低至78 MPa,性能降低68%;弯曲强度由480 MPa降低至277 MPa,性能降低42%;拉伸强度由247 MPa降低至152 MPa,性能降低38%。高温氧化导致界面退化,损伤材料基体与碳纤维结构,加剧了纤维断裂程度,改变了纤维与基体的结合状态,纤维增韧机制逐渐消失,导致复合材料性能下降。     

高速电弧喷涂FeCrBSiMnNbW非晶纳米晶涂层组织及性能

研究开发了一种FeCrBSiMnNbW新型喷涂粉芯丝材,并采用自动化高速电弧喷涂技术在镁合金基体上制备了FecrBsiMnNbw非晶纳米晶涂层。对Fe基非晶纳米晶涂层和传统的3Cr13涂层的组织结构、力学性能以及油润滑条件下的摩擦学性能进行了对比分析,结果表明：与3Cr13涂层相比,铁基非晶纳米晶涂层组织更加致密,孔隙率低,具有相对较高的硬度和拉伸结合强度;形成了非晶相和纳米晶相组成的复合结构,使得涂层具备更好的摩擦学性能。     

微胶囊型自修复碳纤维增强复合材料性能研究

为了分析内嵌环氧树脂基微胶囊的碳纤维增强复合材料(CFRP)的力学性能,开展了材料在准静态载荷条件下力学性能试验研究,对比分析了有、无微胶囊时碳纤维增强复合材料的静态力学性能,详细探究了微胶囊的质量分数对碳纤维增强复合材料的力学性能和自修复性能的影响,分析了材料的拉伸强度,弹性模量,断裂伸长率以及自修复性能情况。在相同冲击能量下,采用落锤法对不同微胶囊含量的层合板进行冲击试验,研究其在冲击载荷作用下的动态力学响应。结果表明,微胶囊具有增韧效果和自修复能力。随着微胶囊质量分数的增加,自修复碳纤维增强复合材料的拉伸强度降低,弹性模量先略微升高后降低,断裂伸长率先降低后升高,但总体变化不大,修复效率随微胶囊含量的增加而升高。在相同冲击能量下,微胶囊含量越大,最大冲击力越小,材料的冲击力-位移曲线斜率越小,抗冲击性能越差。研究结果可以为推动自修复型CFRP材料的实际工程应用和理论研究提供相关参考。     

夹芯复合材料T型接头侧弯损伤机理及强度特性分析

针对复合材料夹芯板材构件的侧弯承载和坚固连接要求,设计了弧形过渡区增强型T型胶接接头。建立了夹芯复合材料T型接头数值模型,模拟了其在侧弯载荷作用下的损伤产生、扩展及失效过程,并对夹芯复合材料T型接头试件进行了静态侧弯试验。结果表明:接头发生初始损伤的线载荷强度为44~47N/mm,损伤发生后接头的刚度值发生折减(降低约28%~32%),此时接头的承载能力仍在上升;试件界面完全剥离载荷强度较初始损伤线载荷强度略有增加(线载荷强度范围为54~62N/mm)。数值计算与试验结果吻合,表明弧形过渡区是夹芯复合材料T型接头最薄弱的部位,易发生破坏;初始损伤将首先出现在弧形过渡区复合材料表层,随着层间裂纹的扩展,过渡区复合材料与芯材的复合界面处出现剥离破坏并向自由端端部界面扩展,这是导致夹芯复合材料T型胶接接头失效的最主要原因。     

石英纤维增强苯并噁嗪树脂复合材料研究

对苯并(啞心)嗪树脂应用于RTM工艺制备石英纤维增强复合材料进行了研究.系统考察了该树脂的工艺性能及力学性能,制备并测试了石英/苯并(啞心)嗪复合材料的力学性能及耐烧蚀性能,并将相关性能与钡酚醛与石英/钡酚醛进行了比较.结果表明,在85℃～145℃温度区间内苯并(啞心)嗪树脂粘度保持在800mPa·s以下,树脂具有较宽的低粘度温度平台和较长的低粘度保持时间.力学性能及耐烧蚀性能研究表明,石英/苯并(啞心)嗪复合材料的层间剪切强达到了61.5MPa,拉伸强度和弯曲强度显著优于石英,钡酚醛复合材料,质量烧蚀率和线烧蚀率分别为0.0510g·s-1和0.032mm·s-1.石英/苯并(啞心)嗪复合材料是一种可采用RTM工艺制备的耐烧蚀材料.     

整体缝合夹芯结构复合材料力学性能

所设计的新型整体缝合泡沫夹芯复合材料结构,能够避免一般斜缝方式引起纤维交叉损坏的弊端。采用真空导入模塑工艺制备整体缝合泡沫夹芯结构复合材料,研究缝合结构、缝合方式以及缝合纱线用量对整体缝合泡沫夹芯复合材料平压力学性能和弯曲性能的影响。结果表明,新型缝合结构在保证平压力学性能的同时,相比于垂直缝合结构弯曲破坏载荷提高了94.4%;穿透缝合方式能够显著提高试样的平压强度和弯曲破坏载荷;随着缝合纱线用量的增加,整体缝合泡沫夹芯复合材料的压缩和弯曲性能显著提高。     

裂解温度对PIP制备2D Cf/Si-O-C复合材料结构与性能的影响

以二维碳纤维布、硅树脂先驱体、SiC微粉和乙醇溶剂为原料,采用先驱体转化工艺制备了2D Cf/Si-O-C复合材料,考察了裂解温度对材料结构和性能的影响。结果表明,首周期裂解温度对制备材料的力学性能有重要影响,纤维-基体间的界面弱化是复合材料力学性能提高的主要原因;第6周期采用合适的温度裂解可提高复合材料的力学性能,其弯曲强度和断裂韧性分别达到了263.9MPa和12.8MPa.m1/2。     

Investigation of the mechanical and ballistic properties of hybrid carbon/ aramid woven laminates

High-performance ballistic fibers, such as aramid fiber and ultra-high-molecular-weight polyethylene (UHMWPE), are commonly used in anti-ballistic structures due to their low density, high tensile strength and high specific modulus. However, their low modulus in the thickness direction and insufficient shear strength limits their application in certain ballistic structure. In contrast, carbon fiber reinforced epoxy resin matrix composites (CFRP) have the characteristics of high modulus in the thickness direction and high shear resistance. However, carbon fibers are rarely used and applied for protection purposes. A hybridization with aramid fiber reinforced epoxy resin matrix composites (AFRP) and CFRP has the potential to improve the stiffness and the ballistic property of the typical ballistic fiber composites. The hybrid effects on the flexural property and ballistic performance of the hybrid CFRP/AFRP laminates were investigated. Through conducting mechanical property tests and ballistic tests, two sets of reliable simulation parameters for AFRP and CFRP were established using LS-DYNA software, respectively. The experimental results suggested that by increasing the content of CFRP that the flexural properties of hybrid CFRP/AFRP laminates were enhanced. The ballistic tests’ results and the simulation illustrated that the specific energy absorption by the perforation method of CFRP achieved 77.7% of AFRP. When CFRP was on the striking face, the shear resistance of the laminates and the resistance force to the projectiles was promoted at the initial penetration stage. The proportion of fiber tensile failures in the AFRP layers was also enhanced with the addition of CFRP during the penetration process. These improvements resulted in the ballistic performance of hybrid CFRP/AFRP laminates was better than AFRP when the CFRP content was 20 wt% and 30 wt%.     

碳纤维增强聚合物基复合材料频率选择表面的电磁传输特性（复合材料专栏投稿）*

为了改善采用金属频率选择表面（Frequency Selective Surface,FSS）制备的天线罩中存在的热残余应力和弱粘接界面等问题,本文采用与聚合物基复合材料罩壁结构相容性好的碳纤维增强聚合物基复合材料制备FSS,利用自由空间法对试样的电磁传输性能进行测试,并采用数值分析模型对碳纤维复合材料FSS的电磁传输机制和电磁传输影响因子进行分析。结果表明：碳纤维复合材料FSS具有频率选择功能,但谐振频率处的电磁传输损耗较大;通过改变复合材料FSS的单元缝隙率、厚度、电导率以及介电常数可以实现对其电磁传输性能的调节。     

Synergistic effect of hybrid Himalayan Nettle/Bauhinia-vahlii fibers on physico-mechanical and sliding wear properties of epoxy composites

The cellulosic bast fibers are recognized as a justifiable and biodegradable substitute for producing moderate strength polymer composite materials because of their characteristics of renewability, eco-friendliness, and higher specific strength. Hence the aim of this research work is to fabricate Himalayan bast fibers (Nettle fiber (NF)/bauhinia vahlii fiber (BF)) based mono/hybrid epoxy composites at varying weight percentage of 2–6 wt% and evaluate the physical (void fraction and water absorption), mechanical (tensile strength, flexural strength, hardness) and sliding wear properties of as-fabricated composites. The 6 wt% NBF reinforced composites exhibited higher mechanical properties as compared to NF and BF composites with tensile strength of 34.04 MPa, flexural strength of 42.45 MPa, and hardness of 37.01 H_v respectively. The influence of various control factors (sliding velocity, NF/BF/NBF contents, normal load and sliding distance) on specific sliding wear rate of composites was evaluated by Taguchi (three factors at three levels) experimental design and the percentage contribution of these selected parameters on sliding wear performance was examined by Analysis of variance (ANOVA). The sliding wear property of as-developed composites was found to be greatly influenced by sliding velocity and the wear resistance was observed to be improved with the NF/BF/NBF contents. The wear mechanism of the as-fabricated composites has been elucidated by scanning electron microscopy analysis. The research outcomes demonstrated that the hybridization of Bauhinia vahlii fiber with Nettle fiber led to improve the mechanical and wear properties of epoxy composites.     

用溶胶-凝胶法制备碳纤维三维编织物增强氧化铝基复合材料的研究

本文研究了溶胶－凝胶（Ｓｏｌ－ｇｅｌ）法制备碳纤维三维编织物增强氧化铝（Ａｌ２Ｏ３）基复合材料的成型工艺及其力学性能，研究了两种主要起始物Ａｌ（ＮＯ３）３、ＡｌＣｌ３配制的氧化铝溶胶对复合材料成型工艺和力学性能的影响。分别以Ａｌ（ＮＯ３）３和ＡｌＣｌ３为起始物，制备得到Ⅰ＃、Ｉ＃复合材料。研究表明，以Ａｌ（ＮＯ３）３为起始物配制的溶胶粘度较小，利于材料的致密化。经过溶胶浸渍、凝胶、裂解１３个周期后，Ⅰ＃材料的密度和室温三点弯曲强度分别为１．８６ｇ／ｃｍ３和１４５．２ＭＰａ，而ＩＩ＃材料的密度和室温三点弯曲强度分别为１．６３ｇ／ｃｍ３和１０４．１ＭＰａ，材料均呈典型的韧性断裂模式。用扫描电子显微镜（ＳＥＭ）观察试样的断口形貌，发现断口表面有大量的纤维拔出，纤维表现了较好的增韧效果。     

UHMWPE纤维混凝土基本力学性能研究

研究了一种由超高分子量聚乙烯（UHMWPE）纤维增强的新型纤维混凝土基本力学性能。针对C70等级高强混凝土,设计了四种体积掺量纤维混凝土,通过立方体抗压、劈裂抗拉和四点弯曲抗折试验,分析了纤维掺量对混凝土力学性能的影响。结果表明：UHMWPE纤维对混凝土的抗压强度增强作用不明显,但较大提高了混凝土的抗拉强度和抗折强度,且对混凝土有很好的阻裂、增韧效果。在纤维体积掺量为0.3%~0.5%时,劈裂抗拉强度提高25%以上;掺量0.5%时,弯曲抗折强度提高率超过23%。     

高掺量碳纤维增强活性粉末混凝土力学性能实验

采用一种新的碳纤维自分散工艺和专用分散设备制备出了掺量达胶结材质量8％的碳纤维增强活性粉末混凝土;研究了碳纤维掺量对活性粉末混凝土的力学性能影响规律。实验结果表明,在碳纤维掺量高时,活性粉末混凝土的力学性能受碳纤维掺量和水胶比两个因素共同作用。     

纤维增强SiO2气凝胶隔热复合材料的制备及其性能

将无机陶瓷纤维与SiO2溶胶混合,经超临界干燥制备了SiO2气凝胶隔热复合材料。SiO2气凝胶纤细的骨架颗粒减少了固态热传导,纳米级孔减少了气体热传导和对流传热,同时无机陶瓷纤维减少了辐射传热。SiO2气凝胶复合材料具有良好的隔热性能,其200℃和800℃的热导率分别为0.017W/m.K和0.042W/m.K。纤维的加入提供了力学支撑,高温处理增强了气凝胶骨架强度,材料在常温和高温下均具有良好的力学性能,其常温的拉伸、弯曲和抗压强度分别为1.44MPa、1.31MPa和0.98MPa(10%应变),800℃的拉伸、弯曲和抗压强度分别为1.95MPa、1.80MPa和1.42MPa(10%应变)。     

SiC纤维表面CVD SiC涂层对其单丝强度的影响

采用化学气相沉积(CVD, Chemical Vapor Deposition)工艺在KD-I型SiC纤维表面制备了SiC涂层,选择2h、4h、6h和8h四个时间点研究了沉积时间对纤维性能的影响.结果表明:具有CVD SiC涂层的SiC纤维较无涂层的纤维来说强度有所下降;在所研究的沉积时间范围内,随着沉积时间的增加,涂层的厚度有所增加,涂层由不连续的岛状转变为连续层状,纤维的单丝强度出现了先升后降的趋势.     

A theoretical justification for an increasing average failure rate strength distribution in fibrous composites

A general model for the failure of fibrous composite materials is described. It is shown to contain some of the well-known models in the literature. The composite material is viewed as a coherent system of independent identically distributed component strengths. Under the assumption that the applied load is redistributed “homotonically” to the unfailed components upon the failure of a component (an individual fiber segment) and that the distributions of component strengths are IFRA, it is shown that the system (composite) strength distribution is also IFRA. Examples are given using carbon reinforced composite data to illustrate the IFRA property.