一个功能较强的等离子体电磁波粒子模拟程序

本文发展了一个功能较强的1 2/2D 等离子体粒子模拟程序。文中就一维情况,论述了等离子体粒子模拟的原理、方法和计算机编程中的处理技巧。最后讨论了电磁模拟的应用。     

15cm×15cm 磁悬挂天平系统(MSBS)的电磁场分析与计算

本文采用二维电磁场有限元法及磁路的简化计算法对15cm×15cm磁悬挂天平系统（MSBS）的阻力线圈间距、磁场的分布情况进行了分析计算,并与测试结果进行了分析比较,给出了15cm×15cm磁悬挂天平系统（MSBS）的结构方案。     

氦原子1S, 3S, 1P, 3P态的电子关联计算

本文从二次量子化公式出发,选取广义Laguerre多项式乘以γ~lcxp(-alγ)作为单电子径向函数完全集,这里a_l是依赖于轨道角动量l的变分参数,用组态相互作用方法计算了氨原子~1S,~3S,~1P,~3P态的能量和波函数。当组态限于主量子数n≤4,计算的能量相对精度约为99.9%;当组态限于%≤6,能量相对精度约为99.99%;而Hartree Fock方法的能量相对精度约为99%,利用原子波函数计算了一些原子参数,其结果与其他作者的结果符合很好。     

一阶与二阶常微分方程系统的隐式和半隐式解法

本文对于非定常问题在经Galerkin半离散化所得到的一阶及二阶常微分方程系统分别提出了具有二级精度的隐式和牛隐式求解方案,并从数学上严格证明了这两个数值方案均是无条件稳定的;另对于正定对称矩阵,通过应用近似求逆法大大地减少了计算工作量;最后提供了两个简单算例,证明本方法是行之有效的。     

混沌检测在雷达信号测试中的应用

为解决雷达测试信噪比很小的信号检测问题,分析了噪声特性和多普勒信号特性,论述了混沌检测原理,提出了混沌检测方法,并通过实验对混沌检测的可行性及实用性进行了验证。     

交通场景行人穿越检测方法进展研究

随着自动驾驶和计算机视觉技术的飞速发展,人们对交通安全的重视程度越来越高。其中,交通场景中行人穿越检测问题是研究的热点与难点之一。对行人穿越检测这一领域进行了综合评述,并对未来研究进行了展望。按照行人试图穿越、正在穿越及穿越预测三个阶段进行分析,首先分析了基于行人姿态穿越意图的研究进展(试图穿越),包括人体姿态、数据驱动和高斯动力学模型三个方面;其次讨论了基于轨迹跟踪的穿越行为检测方法(正在穿越);然后概括了基于轨迹预测的行人穿越检测方法(穿越预测);最后总结了现阶段比较新颖的多传感融合、车路协同、车联网等研究角度,并对未来该领域需重点发展的方向提出建议。     

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.     

Gas metal arc welding of high nitrogen stainless steel with Ar-N2-O2 ternary shielding gas

High nitrogen stainless steel with nitrogen content of 0.75％was welded by gas metal arc welding with Ar—N2-O2 ternary shielding gas. The effect of the ternary shielding gas on the retention and improvement of nitrogen content in the weld was identified. Surfacing test was conducted first to compare the ability of O2 and CO2 in prompting nitrogen dissolution. The nitrogen content of the surfacing metal with O2 is slightly higher than CO2. And then Ar—N2-O2 shielding gas was applied to weld high nitrogen stainless steel. After using N2-containing shielding gas, the nitrogen content of the weld was improved by 0.1 wt％. As N2 continued to increase, the increment of nitrogen content was not obvious, but the ferrite decreased from the top to the bottom. When the proportion of N2 reached 20％, a full austenitic weld was obtained and the tensile strength was improved by 8.7％. Combined with the results of surfacing test and welding test, it is concluded that the main effect of N2 is to inhibit the escape of nitrogen and suppress the ni-trogen diffusion from bottom to the top in the molten pool.     

Mechanical behavior and failure mechanism of polyurea nanocomposites under quasi-static and dynamic compressive loading

Polyurea is an elastomeric material that can be applied to enhance the protection ability of structures under blast and impact loading.In order to study the compressive mechanical properties of SiC/polyurea nanocomposites under quasi-static and dynamic loading,a universal testing machine and split Hop-kinson pressure bar(SHPB)apparatus were used respectively.The stress-strain curves were obtained on polyurea and its composites at strain rates of 0.001-8000 s-1.The results of the experiment suggested that increase in the strain rates led to the rise of the flow stress,compressive strength,strain rate sensitivity and strain energy.This indicates that all of the presented materials were dependent on strain rate.Moreover,these mechanical characters were enhanced by incorporating a small amount of SiC into polyurea matrix.The relation between yield stress and strain rates were established using the power law functions.Finally,in order to investigate the fracture surfaces and inside information of failed specimens,scanning electron microscopy(SEM)and micro X-ray computed tomography(micro-CT)were used respectively.Multiple voids,crazes,micro-cracks and cracking were observed in fracture surfaces.On the other hand,the cracking propagation was found in the micro-CT slice images.It is essential to understand the deformation and failure mechanisms in all the polyurea materials.