顶部开口条件下油罐油气爆炸数值模拟

根据油罐油气爆炸特性,基于RNG k-ε湍流模型、Finate-Rate/Eddy-Dissipation化学反应模型和相应的控制方程,采用SIMPLE算法对顶部开口条件下油气爆炸发生与发展过程进行了数值模拟。基于数值模拟结果分析了顶部开口条件下油罐油气爆炸罐外超压和火焰特征,与实验结果吻合良好,该模型可以用来预测顶部开口条件下油罐油气爆炸强度。     

基于变转速的柴油抗磨性评定方法

以MRS-1J型四球摩擦磨损试验机为平台,提出了一种变转速条件下柴油抗磨性评定方法。利用VC＋＋对试验机软件进行了改进,增加了负荷-转速程序控制功能,实现了试验机自由设置转速、负荷的变化范围、变化速率和变化模式。通过正交试验方法确定了最佳试验条件,发现试验时间3N1min,负荷11N2N,油温60℃,转速在1 min内由100 r/min线性上升至20N3r/min再线性下降至100 r/min并依次循环时,该试验方法具有良好的重复性和区分性。在与高频往复试验机法的对比中,发现该方法的磨斑直径变化率大于高频往复试验机法,证明变转速四球机法优于高频往复试验机法。     

单点系泊船舶Hopf分岔的试验研究

对单点系泊船舶的Hopf分岔现象进行了试验研究.给出了试验方法和过程;探讨了不同来流速度和系缆长度对于船舶动力学响应的影响.试验表明,船模运动呈现出典型的非线性特征,观察到了吸引子的共存,平衡点稳定性丧失和Hopf分岔现象.利用振动衰减系数计算了Hopf分岔值,与试验结果相比较,具有良好的一致性.得到了试验条件下的Hopf分岔集,指出其对于系泊系统的设计是有指导意义的.     

Effect of projectile parameters on opening behavior of PELE penetrating RC target

When a penetrator with enhanced lateral effect (PELE) impacts on a reinforced concrete (RC) target, the target is damaged with a large opening. An understanding of how PELE projectile parameters affect the opening dimension, is essential for effective design of the PELE projectile. In this study, under the condition that the impact velocity and target parameters (strength and thickness) were fixed values, the important influence factors of the PELE (jacket wall thickness B, jacket material strength Y1, filling material strength Y2 and angle of monolithic jacketθ) were determined by a dimensional analysis. Tests and simulations of the PELE penetrating the RC target were conducted to analyze the influence of these factors on opening diameter ((D), an equivalent diameter under relative kinetic energy). Based on the test and simulation results, it is found that the influence of these factors B, Y1 andθon the deformation mode of the jacket shows a similar trend:as values of the three factors decrease, the jacket deforms from small bending deformation to large one, and then to curling deformation. This causes the opening diameter to first increase with the decrease of these three factors, and then decreases. It is well known that the bending resistance of the jacket is related to these factors B, Y1 andθ. Therefore, a plastic limit bending moment (M0) of the jacket was quoted to characterize the influence of these factors on the bending deformation of the jacket and the opening diameter of the target. The influence factor Y2 causes (D) to first increase with the increase of Y2, and then decreases. A formula was developed to predict the opening diameter, whose influence parameters were considered in a dimensionless way. It has been shown that the dimensionless opening diameter (D)/d1 is dependent on two dimensionless parameters Q = (d31fc/M0) and G = (fc/Y2), where d1 and fc are the outer diameter of the projectile and the compressive strength of the target, respectively.     

正规模糊测度空间上的条件期望

讨论了次可加、具有有界变差的正规模糊测度空间上关于模糊测度、内测度及模糊积分的性质，在此基础上定义了此模糊测度空间上随机变量的条件数学期望，它是相对于经典测度空间的一个推广。     

圆柱形微带天线的复合材料设计

本文介绍了满足微带天线使用温度要求的聚合物基复合材料设计的方法与过程。按照这种方法,设计并制造了一批微带天线产品,经高低温测试,证明都符合设计要求。     

聚氨酯型复合推进剂的性能研究

本文研究聚氨酯型复合推进剂的力学性能和燃烧性能,给出了提高推进剂力学性能的有效途径,测试了推进剂燃烧性能的基本特征参数,采用光电子能谱(ESCA)对这种复合推进剂的界面作用机理进行了微观探讨.     

室内消火栓出水量及栓口所需水压的简化计算

本文主要通过室内消火栓的简化计算,将复杂的计算简化为查表就能直接得到消火栓栓口所需压力,为设计人员及消防工作者提供了方便。     

深入学习贯彻科学发展观需要把握的几个问题

学习贯彻科学发展观,是部队当前首要的政治任务,是各级党委领导的第一位政治责任,必须作为政治工作的主线突出出来,在深化思想认识、全面系统学习理解、进入实践推动工作、加强组织领导等方面下更大功夫,从而把学习贯彻科学发展观不断引向深入。     

美军无人地面车辆概述（一）

对美国陆军无人地面车辆（又称军用机器人）进行概要介绍,编译的原文为截止到2007年底的美国政府公开发布资料,分为引言、轻型无人地面车辆、中型无人地面车辆、重型无人地面车辆、大型无人地面车辆等5章,包括20多种研制和投入使用的型号,本文为第一部分。