中国海防史研究述评

海防史所涉及的范围非常广泛,研究中国海防史具有非常重要的现实意义。从上个世纪特别是近二十年以来,随着中国海防意识的逐步提高,中国海防史所取得的研究成果越来越引人注目。对中国海防史的研究成果进行回顾和反思,必将促进其研究向更纵深方向发展。     

Effect of projectile parameters on opening behavior of PELE penetrating RC target

When a penetrator with enhanced lateral effect (PELE) impacts on a reinforced concrete (RC) target, the target is damaged with a large opening. An understanding of how PELE projectile parameters affect the opening dimension, is essential for effective design of the PELE projectile. In this study, under the condition that the impact velocity and target parameters (strength and thickness) were fixed values, the important influence factors of the PELE (jacket wall thickness B, jacket material strength Y1, filling material strength Y2 and angle of monolithic jacketθ) were determined by a dimensional analysis. Tests and simulations of the PELE penetrating the RC target were conducted to analyze the influence of these factors on opening diameter ((D), an equivalent diameter under relative kinetic energy). Based on the test and simulation results, it is found that the influence of these factors B, Y1 andθon the deformation mode of the jacket shows a similar trend:as values of the three factors decrease, the jacket deforms from small bending deformation to large one, and then to curling deformation. This causes the opening diameter to first increase with the decrease of these three factors, and then decreases. It is well known that the bending resistance of the jacket is related to these factors B, Y1 andθ. Therefore, a plastic limit bending moment (M0) of the jacket was quoted to characterize the influence of these factors on the bending deformation of the jacket and the opening diameter of the target. The influence factor Y2 causes (D) to first increase with the increase of Y2, and then decreases. A formula was developed to predict the opening diameter, whose influence parameters were considered in a dimensionless way. It has been shown that the dimensionless opening diameter (D)/d1 is dependent on two dimensionless parameters Q = (d31fc/M0) and G = (fc/Y2), where d1 and fc are the outer diameter of the projectile and the compressive strength of the target, respectively.     

Mitigation of the blast load effects on a building structure using newly composite structural configurations

In this study, a nonlinear three-dimensional hydrocode numerical simulation was carried out using AUTODYN-3D to investigate the effect of blasting of a high explosive material (TNT) against several configurations of the composite structure. Several numerical models were carried out to study the effect of varying the thickness of the walls and the effect of adding an air layer or aluminum foam layer inside two layers of concrete in mitigating the effect of blast waves on the structure walls. The results showed that increasing the thickness of walls has a good effect on mitigating the effect of blast waves. When a layer of air was added, the effect of blast waves was exaggerated, while when a layer of aluminum foam was added the blast wave effects were mitigated with a reasonable percentage.     

德文版液压系统模拟仿真软件的汉化方法

介绍了德文版的 Fluid SIM-H液压系统模拟仿真软件 ,并介绍了应用 Exe Scope、Help Deco、Help Work和 Create Install等工具软件对德文版软件进行汉化的基本方法     

应用最大熵谱估计进行导弹系统的仿真模型验证

探讨了导弹系统仿真模型验证的定量方法。依据最大熵谱估计方法分辨力高的特点，分析其近似统计特性，分别给出了两个样本和两个正态总体的一致性检验方法。仿真结果表明，利用最大熵谱估计进行有效性检验是可行的。最后给出了一个应用实例，应用谱估计方法进行寻的制导导弹数字仿真模型验证     

功率循环下IGBT模块电热参数变化规律分析

为了分析IGBT模块老化过程中电热参数的变化规律,对IGBT模块进行了功率循环加速老化试验,并基于单脉冲测试方法在加速老化试验进程中每间隔1 000次功率循环,测取一次IGBT的结温、集电极电流与饱和压降三维关系曲面、开关能耗、热阻抗以及瞬态热阻抗曲线。IGBT模块老化失效时,其饱和压降、开通能耗、关断能耗以及热阻较其初始值分别增大了3.92%、12.05%、18.87%和22.65%,试验结果表明随着IGBT模块功率循环次数的增多,相同工作条件下IGBT饱和压降的增幅逐渐加大,而饱和压降、结温和集电极电流三者间的内在关系没有明显变化;IGBT瞬态热阻抗曲线暂态部分几乎不变,稳态部分向上移动的幅度逐渐加大;测取的IGBT模块电热参数中饱和压降增幅最小,开关能耗增幅较大,模块热阻的增幅最为明显。     

A worst‐case formulation for constrained ranking and selection with input uncertainty

In this research, we consider robust simulation optimization with stochastic constraints. In particular, we focus on the ranking and selection problem in which the computing time is sufficient to evaluate all the designs (solutions) under consideration. Given a fixed simulation budget, we aim at maximizing the probability of correct selection (PCS) for the best feasible design, where the objective and constraint measures are assessed by their worst‐case performances. To simplify the complexity of PCS, we develop an approximated probability measure and derive the asymptotic optimality condition (optimality condition as the simulation budget goes to infinity) of the resulting problem. A sequential selection procedure is then designed within the optimal computing budget allocation framework. The high efficiency of the proposed procedure is tested via a number of numerical examples. In addition, we provide some useful insights into the efficiency of a budget allocation procedure.     

某型弹用闪光灯环境试验后光通量下降原因分析

本文通过对某型弹用闪光灯环境试验后出现光通量下降问题进行原因分析,经过查找,发现是由于试验方法不当造成闪光次数过多导致环氧胶过热挥发,污染了光学元件直接造成了闪光灯光通量的降低,给后续型号研制提供了经验教训。     

GJB 908A-2008《首件鉴定》实践应用浅析

本文主要是结合工作实践,从全面把握标准内涵、综合掌握相关的信息,开展首件鉴定工作的条款要求等方面对GJB 908A-2008实践应用的认识和体会。