基于线性四分树描述的图像块邻域寻找的快速方法

线性四分树将物体区域表示为组成物体区域的四分块的位置码的集合。本文通过分析位置码属性,归纳出了图像四分块相邻的充要条件,并给出了相应的寻找图像块邻域的算法。该方法简单明了,便于计算机实现。     

机构的工作能力与约束条件

本文是“机构可靠性”的续篇.进一步讨论了机构的工作能力和约束条件,将其划分为构件的和运动副的工作能力与约束条件,给出了描述方法,为机构可靠性与工作能力的定量分析打下了基础.     

基于合成沸石的Cr~(3+)深度吸附处理

以吸附后溶液中Cr3+质量浓度低于国家相关标准为目的,采用搅拌动态吸附的方法,研究投加量、吸附时间、吸附温度、pH值对吸附的影响,考察沸石粉对Cr3+深度吸附的条件。实验发现,在沸石粉投加量为1g/L的前提下,吸附时间为2h、温度为55℃、pH值为4~5时分别达到较好吸附效果。开展三因素三水平正交试验,得到深度吸附条件为:投加量1g/L、吸附时间2h、吸附温度35℃、pH=5,此时去除率达到99.7%。对深度吸附条件进行验证,发现在此条件下可以将Cr3+溶液的质量浓度由0.1mg/L降低至0.03mg/L;最后通过实验得出沸石粉对Cr3+的饱和吸附量为79.93mg/g。     

科氏流量计信号相位差测量新算法

对科氏流量计信号进行处理时,传统相位差测量算法存在较大误差。为更好地抑制频谱泄露,提高相位差测量精度,在传统DTFT算法的基础上,通过矩形窗和汉宁窗卷积运算构造出一种新窗——RHC窗。计及负频率成分的影响,提出了一种基于RHC窗的DTFT相位差测量新算法。详细阐述了新算法的原理,并与传统DTFT算法进行了对比仿真,验证了新算法的有效性。     

A nonatomic‐game model for timing clearance sales under competition

We deal with dynamic revenue management (RM) under competition using the nonatomic‐game approach. Here, a continuum of heterogeneous sellers try to sell the same product over a given time horizon. Each seller can lower his price once at the time of his own choosing, and faces Poisson demand arrival with a rate that is the product of a price‐sensitive term and a market‐dependent term. Different types of sellers interact, and their respective prices help shape the overall market in which they operate, thereby influencing the behavior of all sellers. Using the infinite‐seller approximation, which deprives any individual seller of his influence over the entire market, we show the existence of a certain pattern of seller behaviors that collectively produce an environment to which the behavior pattern forms a best response. Such equilibrium behaviors point to the suitability of threshold‐like pricing policies. Our computational study yields insights to RM under competition, such as profound ways in which consumer and competitor types influence seller behaviors and market conditions. © 2014 Wiley Periodicals, Inc. Naval Research Logistics 61: 365–385, 2014     

用伴随方程研究烟幕施放的优化问题

从描述烟幕扩散的基本方程出发,提出了一类烟幕施放的优化问题．文中指出,这类问题由于约束条件为复杂的偏微分方程,计算量很大,难以直接求解．为了解决这一问题,引入了一种伴随方法以降低计算量．推导了三维非平坦地形下大气平流一扩散方程的伴随方程,利用伴随方程和原方程的关系,对优化问题进行了等价变形,大大降低了计算量．最后通过一个算例,对这一方法的有效性进行了演示。     

Formation and characterization of core-shell CL-20/TNT composite prepared by spray-drying technique

The core-shell 2,4,6,8,10,12-Hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane/2,4,6-Trinitrotoluene (CL-20/TNT) composite was prepared by spray-drying method in which sensitive high energy explosive (CL-20) was coated with insensitive explosive (TNT). The structure and properties of different formulations of CL-20/TNT composite and CL-20/TNT mixture were characterized by scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Laser particle size analyzer, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), differential scanning calorimetry (DSC), impact sensitivity test and detonation performance. The results of SEM, TEM, XPS and XRD show that ϵ-CL-20 particles are coated by TNT. When the ratio of CL-20/TNT is 75/25, core-shell structure is well formed, and thickness of the shell is about 20–30 nm. And the analysis of heat and impact show that with the increase of TNT content, the TNT coating on the core-shell composite material can not only catalyze the thermal decomposition of core material (CL-20), but also greatly reduce the impact sensitivity. Compared with the CL-20/TNT mixture (75/25) at the same ratio, the characteristic drop height of core-shell CL-20/TNT composite (75/25) increased by 47.6% and the TNT coating can accelerate the nuclear decomposition in the CL-20/TNT composites. Therefore, the preparation of the core-shell composites can be regarded as a unique means, by which the composites are characterized by controllable decomposition rate, high energy and excellent mechanical sensitivity and could be applied to propellants and other fields.     

Quasi-steady aerodynamic characteristics of Terminal Sensitive Bullets with short cylindrical portion

The aerodynamic characteristics are vital for short cylindrical Terminal Sensitive Bullets(TSB)with low aspect ratio,especially in terminal trajectory.Currently,there is little research in terms of the TSB and short cylinder with two free ends,and particularly in this trajectory,where the scanning angle β and roll angle α vary over a broad range between 0° and 180°.In this work,wind tunnel experiments are first conducted to learn the effects of Reynolds number and scanning angle on aerodynamic parameters for short cylinder with aspect ratio L/D = 1.Similar to infinite cylinder,for the short cylinder with two free ends,the drag crisis phenomenon still exists in the critical regime 1.7 × 105 ≤ Re ≤ 6.8 × 105.Then 3D simulations are performed to demonstrate the aerodynamic characteristics of short cylinder and TSB over a broad range of Re,L/D,α and β.The sensitivity analysis of time step and grid are presented as well.When β=0°,for short cylinder,the drag crisis phenomenon was also observed in the simulation,but not as obvious as in the wind tunnel test.In some attitudes,there is an obvious Kármán vortex in the wake of short cylinder and TSB.The correlation between time-averaged aerodynamic coefficients and L/D,Re,α&β is discussed.The vortex shedding frequency and shear layer behavior are obtained for quasi-steady and unsteady flow.Finally,the effect of end's shape on drag reduction and vortex shedding frequency is analyzed.     

Design and analysis of a scheme for the naval gun test shell entering the bore

The test shell without projectile belt is widely used in the teaching, inspection and maintenance of modern automatic naval guns. In order to ensure the normal work of each mechanism, it is very important to design the buffer and limit of the test shell during the process of entering the bore. Taking a certain type of medium caliber naval gun as the research object, the design of colloidal fluid damper and cartridge lock was proposed to ensure the reliability of entering the bore and closing the breechblock. By combining the simulation methods of computational fluid dynamics (CFD) and multibody system dy-namic (MBD), it was analyzed whether the structural design can meet the engineering requirements. The research results show that the colloidal fluid damper can dissipate a large amount of kinetic energy of the shell, and the cartridge lock can limit the rebound movement. The combination of the two ensures the smooth process of closing the breechblock. The research provides a design method for the process of the test shell entering the bore, and provides theoretical support for the feasibility of the method.     

Experimental investigation on anti-penetration performance of polyurea-coated ASTM1045 steel plate subjected to projectile impact

In this study, the anti-penetration performance of polyurea/ASTM1405-steel composite plate subjected to high velocity projectile was analyzed. Two kinds of modified polyurea material (AMMT-053 and AMMT-055) were selected and a ballistic impact testing system including speed measuring target system and high-speed camera was designed. This experiment was conducted with a rifle and 5.8 mm projectile to explore the effects by the polyurea coating thickness, the polyurea coating position and the glass-fiber cloth on the anti-penetration performance of polyurea/ASTM1405-steel composite plate. The result showed that the effects of polyurea coating position were different between two types of polyurea, and that the effects of glass-fiber position were disparate between two types of polyurea as well. For AMMT-053 polyurea material, it was better to be on front face than on rear face; whereas for AMMT-055 pol-yurea, it was better to be on rear surface although the difference was very subtle. Additionally, formulas had been given to describe the relationship between the effectiveness of polyurea and the thickness of polyurea coating. In general, AMMT-055 had better anti-penetration performance than AMMT-053. Furthermore, five typical damage modes including self-healing, crack, local bulge, spallation and local fragmentation were defined and the failure mechanism was analyzed with the results of SHPB test. Additionally, the bonding strength played an important role in the anti-penetration performance of polyurea/steel composite plate.