A proof for the longest-job-first policy in one-machine scheduling

We consider a one-machine scheduling problem with earliness and tardiness penalties. All jobs are assigned a common due date and the objective is to minimize the total penalty due to job earliness and tardiness. We are interested in finding the optimal combination of the common due-date value and the job sequence. Despite the fact that this problem in general is very hard to solve, we prove that there exists at least a common property for all optimal solutions: The first job in an optimal sequence is one of the longest jobs. We also prove that this property holds for a general class of unimodal penalty functions.     

Sole sourcing versus dual sourcing under stochastic demands and lead times

The use of a single vendor for each inventoried item is usually assumed in most of the inventory models. However, there are situations where the use of more than one vendor should be considered, especially when lead times are stochastic. This research presents a theoretical investigation of the effect of cost structures on the relative performance of sole-sourcing versus dual-sourcing inventory control policies. We show that except for cases where the ordering cost is high, the lead-time variability is low, or the customer service level is low, dual sourcing performs better than sole sourcing under the normally distributed demand and shifted-exponential lead times. Moreover, the computational results indicate the dual sourcing provides a better service level than sole sourcing at the optimal solutions, and that dual sourcing results in larger order quantities than sole sourcing, which suggests that attractive quantity discounts may not be in jeopardy when dual sourcing is employed. Finally, because it is generally known that multiple sourcing can enhance the competition among suppliers, material managers should consider splitting purchase orders when two equally qualified suppliers are available. © 1994 John Wiley & Sons, Inc.     

Properties of a three-dimensional estimator

A large-scale simulation was conducted to investigate the statistical properties and the suitability of an estimator that estimates the coordinates of a three-dimensional source, according to the angles at which several observers view the source. The estimator uses a heuristical averaging method of estimates obtained from the solution of six two-dimensional problems that utilize line-to-point transformations. The estimator was found to be approximately unbiased with low standard deviations for normal error distributions. An effective and easy-to-use forecasting formula was developed to forecast the parameters of the distributions of the estimates. © 1994 John Wiley & Sons, Inc.     

Employment and utilization of engineers among defense contractors

Defense contractors retain engineers for two reasons. First, engineers work on current-period production contracts. Second, engineers conduct independent research and development (IR&D) and write bids and proposals (B&P) for future contracts. The amount of IR&D/B&P activity, however, understates the amount of effort devoted to learning that reduces the cost of future production. Even some engineers who work on current-period production may engage in learning, as a by-product of their efforts. This article develops and implements a model for estimating the volume of learning activity undertaken by four large manufacturers of military aircraft. © 1994 John Wiley & Sons, Inc.     

A model for use in the rationing of inventory during lead time

While the traditional solution to the problem of meeting stochastically variable demands for inventory during procurement lead time is through the use of some level of safety stock, several authors have suggested that a decision be made to employ some form of rationing so as to protect certain classes of demands against stockout by restricting issues to other classes. Nahmias and Demmy [10] derived an approximate continuous review model of systems with two demand classes which would permit an inventory manager to calculate the expected fill rates per order cycle for high-priority, low-priority, and total system demands for a variety of parameters. The manager would then choose the rationing policy that most closely approximated his fill-rate objectives. This article describes a periodic review model that permits the manager to establish a discrete time rationing policy during lead time by prescribing a desired service level for high-priority demands. The reserve levels necessary to meet this level of service can then be calculated based upon the assumed probability distributions of high- and low-priority demands over lead time. The derived reserve levels vary with the amount of lead time remaining. Simulation tests of the model indicate they are more effective than the single reserve level policy studied by Nahmias and Demmy.     

Should we be using cost of capital in calculating holding costs of consumable inventory?

The DOD directs the usage of 10% of item cost as the cost of capital in the calculation of inventory holding costs. This 10% cost is not totally justified and a complete review must be accomplished to bring this factor to a meaningful and more useful value. The current logic supporting a 10% cost of capital results in a continuing perturbation which forces the Air Force to operate in a less than efficient mode when using the economic order quantity for consumable purchases.     

Multiechelon inventory systems with lateral supply

We develop approximations to estimate the expected backorders in a multiechelon system in which lateral supply actions between bases are allowed when a backorder occurs. These approximations are easy to compute, and the average absolute error over a wide range of parameter values is less than 4% when items are depot repairable, even when bases are dissimilar. With lateral supply, backorder reductions of 30-50% are not uncommon, and a 72% reduction was observed in two cases. Lateral supply becomes more important with low demand rates. A similar approach was unsuccessful for base-repairable items. However, lateral supply has a beneficial effect only when the lateral supply time is very short, 1/4 or less of the average base repair time. Even in such cases lateral supply is unlikely to be important in an actual application, because base management can expedite repair of critical items.     

Scheduling with earliness and tardiness penalties

We show that the deterministic nonpreemptive scheduling problem with earliness and tardiness penalties can be solved in polynomial time for certain forms of an objective function provided that a certain optimization problem can be solved. We give instances where this problem has a solution and show that this generalizes several results from the literature. These results do not require symmetric penalization and the penalty functions need only be lower semicontinuous.     

Optimality of control limit policies in replacement models

We study a class of replacement models for systems subject to deterioration. The objective is to determine an optimal replacement policy that minimizes the average operating costs of the system. We use a parametric analysis to establish sufficient conditions for the optimality of control limit policies. This work generalizes several existing results for optimal replacement models in the literature. © 1992 John Wiley & Sons, Inc.