Numerical and experimental study on the response characteristics of warhead in the fast cook-off process

The response characteristics of the warhead under thermal stimuli conditions are important to the safety improvement. The goal of this study is to obtain data on the warhead in the fast cook-off process. In this paper, a numerical calculation method is proposed, whose reliability is supported by comparison with experimental results. Through the numerical calculation, the temperature distribution, temperature change, and ignition time are acquired. The numerical results show that the ignition time is 76 s after the warhead started to burn and that the maximum temperature of the explosive's outer surface is 238.3 C at the ignition time. The fast cook-off experiment of the warhead is implemented so as to get the flame temperature and reaction grades that are not available through numerical calculation. The experimental results show that the overpressure fails to reach the preset minimum value which is equivalent to 6 kg of TNT and that the reaction grade is deflagration. The research results have reference value for the design of the warhead and the reduction of detonation risks.     

Research on fuze microswitch based on corona discharge effect

Abnormal voltages such as electrostatic, constant current, and strong electromagnetic signals can erro-neously trigger operation of MEMS pyrotechnics and control systems in a fuze, which may result in casualties. This study designs a solid-state micro-scale switch by combining the corona gas discharge theory of asymmetric electric fields and Peek's Law. The MEMS switch can be transferred from "off" to"on" through the gas breakdown between the corona electrodes. In the model, one of the two electrodes is spherical and the other flat, so a non-uniform electric field is formed around the electrodes. The theoretical work is as follows. First, the relation among the radius of curvature of the spherical electrode, the discharge gap, and the air breakdown voltage is obtained; to meet the low voltage (30-60 V) required to drive the MEMS switch, the radius of curvature of the spherical electrode needs to be 10-50 μm and the discharge gap between the two electrodes needs to be 9-11 μm. Second, the optimal ratio ε is introduced to parameterize the model. Finally, the corona discharge structural parameters are determined by comparing the theoretical and electric field simulation results. The switch is then fabricated via MEMS processing. A hardware test platform is built and the performing chip tested. It is found that when the electrode gap is 9 μm, the electrostatic voltage is at least 37.3 V, with an error of 2.6% between the actual and theoretical air breakdown voltages. When the electrode gap is 11 μm, the electrostatic voltage is at least 42.3 V, with an error of 10.5% between the actual and theoretical air breakdown voltages. Both cases meet the design requirements.     

Influences of different crossing types on dynamic response of underground cavern subjected to ground shock

An intersecting cavern is a common structural form used in underground engineering, and its safety and stability performance directly control the service performance of the whole project. The dynamic re-sponses of the three kinds of crossing type (+-shaped, T-shaped, L-shaped) caverns subjected to ground shock were studied by numerical simulation. The velocity plus force mode boundary setting method was proposed in the coupled static and dynamic analysis of a deep underground cavern. The results show that, among the three types of crossing caverns, the+-shaped cavern is the most significantly affected by the dynamic action, followed by T-shaped, and then L-shaped caverns. The vault settlement, straight wall deformation, vault peak particle velocity, effective plastic strain of surrounding rock, and maximum principal stress and strain at the bottom of the lining of the straight wall increase with the increase of cavern span. The vault settlement, straight wall deformation, effective plastic strain of surrounding rock, and the maximum principal stress and strain at the bottom of lining to the straight wall decrease with the increase of lateral pressure coefficient, and the peak particle velocity at the vault increases. The variation is small compared with the change of cavern span. The influence range of the underground cavern intersection is two cavern diameters from the intersection centre. The bottom of the straight wall at the intersection is the weak part. It is suggested to thicken the support locally to improve the stability of the cavern.     

A reusable planar triggered spark-gap switch batched-fabricated with PCB technology for medium-and low-voltage pulse power systems

Triggered spark-gap switch is a popular discharge switch for pulse power systems. Previous studies have focused on planarizing this switch using thin film techniques in order to meet the requirements of compact size in the systems. Such switches are one-shot due to electrodes being too thin to sufficiently resist spark-erosion. Additionally, these switches did not employ any structures in securing internal gas composition, resulting in inconsistent performance under harsh atmospheres. In this work, a novel planar triggered spark-gap switch (PTS) with a hermetically sealed cavity was batched-prepared with printed circuit board (PCB) technology, to achieve reusability with low cost. The proposed PTS was inspected by micro-computed tomography to ensure PCB techniques meet the requirements of machining precision. The results from electrical experiments demonstrated that PCB PTS were consistent and reusable with lifespan over 20 times. The calculated switch voltage and circuit current were consistent with those derived from real-world measurements. Finally, PCB PTS was used to introduce hexanitrostilbene (HNS) pellets in a pulse power system to verify its performance.     

一类参数激励与强迫激励并存的非线性振动系统的分叉

本文用Ｌｉａｐｕｎｏｖ—Ｓｃｈｍｉｄｔ方法研究了同时受参数激励与强迫激励作用的非线性振动系统的亚谐分叉问题,用奇异性理论确定了等价意义下的分叉方程的形式,导出了必需的分叉系数,求出并且分析了１／２—１／２亚谐共振分叉方程的普适开折,画出了各个结构稳定域及分叉集上的响应图。     

光学仪器快速干燥仪的研制

本文从通用性出发利用现代制冷除湿和吸附除湿技术,设计了多功能部件,成功地研制了光学仪器快速干燥仪。通过校核计算及实际应用,完全满足了光学仪害性能的使用要求。     

分布式操作系统MTA－OS的设计研究

介绍了一个用于空－空多目标攻击数字仿真的分布式操作系统ＭＴＡ－ＯＳ的设计思想、系统结构、组成及主要功能。     

基于多尺度小波变换的二维图像角点检测技术

提出一种基于多尺度小波变换的二维图像角点检测算法。首先利用二维零交叉边缘检测算子对图像进行边缘提取得到二值边缘图，通过基于边素（边过程）的围线跟踪算法得到图像的边缘围线。对边缘围线的方向曲线进行多尺度小波变换，利用变换结果的局部最大值信息检测和定位出图像角点。仿真结果表明该算法可有效地实现二维图像的角点检测与定位，具有较高的精度     

组网雷达跟踪系统的类结构设计

本文基于面向对象设计思想,建立了组网雷达跟踪系统的三种类,即：１）传感器／目标类;２）跟踪算法类;３）融合跟踪控制类,并在分布式Ｃｌｉｅｎｔ／Ｓｅｒｖｅｒ计算机系统的网络计算平台上开发了组网雷达跟踪软件系统。该系统可实时、有效地跟踪飞行目标;在恶劣的环境下,具有扩充、重建和重组能力,保证了目标跟踪精度的高质量