高强度热处理双相钢制绳线材研制

本文通过实验提出了一种双相钢制绳线材的热处理工艺程序,即:奥氏体化及水淬以获得全部马氏体组织→临界间加热淬火以获双相组织并回火→酸洗磷化后多道次连续冷拔至终尺寸→人工时效。按此程序生产的线材σ_b 可达1800MPa 以上,且扭转、弯曲疲劳性能超过标准规定值。     

复合导线高电导特性的机理分析

分析了复合导线在一定的频域,其导电性能优于铜导线的高电导特性的物理实质.认为,这种特性是由于电磁波在导线内部界面上的反射引起的.     

复铜导线传输性能的初步探讨

本文对复铜导线的导电性能进行了初步探讨,计算出复铜导线的直流电导率和交流电阻、电感等传输参数以及它们与铜层厚度的相互关系,为进一步对复铜导线的研制和开发提供理论依据.     

通信用复铜导线的开发研究

本文介绍了设备研制、工艺研究、镀液性能及工化生产情况.对φ1.0mm铜包钢裸线及SYKV—75—5同轴电缆(铜色钢内导体)的性能进行了测试,测试结果全部合格.     

铜铝导线搭接处铜导线形貌和成分分析

选用单芯聚氯乙烯绝缘铜导线和铝导线为实验材料并模拟火场条件,制备铜、铝导线搭接形成的一次短路痕迹、二次短路痕迹、火烧痕迹、过负荷痕迹和接触不良痕迹,为识别和分析铜、铝导线搭接痕迹并客观地认定火灾原因提供参考。     

复杂线天线的一种矩量法算法

采用矩量法来计算复杂线天线.针对复杂线天线的特点,选择合适的积分方程和基函数的形式,收敛很快;另外对端点和结点的影响也做了处理,提高了计算精确度.     

石英/双酚E型氰酸酯复合材料的制备与性能

采用实验方法研究双酚E型氰酸酯树脂的黏度和固化特性,揭示催化剂对双酚E型氰酸酯树脂固化特性的影响规律;采用树脂传递模塑和真空导入模塑工艺制备石英纤维/双酚E型氰酸酯复合材料,并考察其力学性能。结果表明,双酚E型氰酸酯树脂室温至90℃范围内的黏度小于300 m Pa·s,凝胶时间大于10 h,起始固化温度、固化温度和终止固化温度分别为186±5℃,235±5℃和286±5℃;固化特征温度随着催化剂含量的增加而降低,直至催化剂饱和,其饱和范围为0.02%~0.03%,可使双酚E型氰酸酯树脂体系的固化温度降低约60℃,从而避免爆聚,实现液相法成型其复合材料;真空导入模塑工艺制备的石英纤维/双酚E型氰酸酯复合材料的力学性能明显优于树脂传递模塑制备试样。     

Effect of nano powder (Al2O3-CaO) addition on the mechanical properties of the polymer blend matrix composite

This work describes the preparation and study of the properties of composite nanoparticles prepared by the sol-gel method which consists of two materials (Al₂O₃-CaO), and study the effect of these nanoparticles on the mechanical behavior of a polymer blend (EP 4% + 96% UPE). The powder was evaluated by X-ray diffraction analysis, scanning electron microscopy analysis (SEM), particle size analysis, and energy dispersive X-ray analysis (EDX). The mechanical behavior of the composite material was assessed by tensile test, bending test and hardness test. The evaluation results of the composite nanoparticles showed good distribution of the chemical composition between aluminum oxide and calcium oxide, smoothness in particles' size at calcination in high and low temperatures, formation of different shapes of nanoparticles and different (kappa and gamma) phases of the Al₂O₃ particles. The results of mechanical behavior tests showed marked improvement in the mechanical properties of the resulted composite material, especially at 1.5%, compared with polymer blend material without nano powder addition. The tensile properties improved about (24 and 14.9) % and bending resistance about (23.5 and 16.8) % and hardness by (25 and 22) % when adding particles of size (63.8 and 68.6) respectively. Therefore, this reflects the efficiency of the proposed method to manufacture the nanocomposite powder and the possibility of using this powder as a strengthening material for the composite materials and using these composite materials in bio applications, especially in the fabrication of artificial limbs.     

Burning rate and other characteristics of strontium titanate (SrTiO3) supplemented AP/HTPB/Al composite propellants

In a quest of search for a new burning rate modifier for composite propellant, strontium titanate (SrTiO₃), a perovskite oxide has been chosen for evaluation in a composite propellant formulation based on its other catalytic applications. Initially, SrTiO₃ was characterized for particle size, morphology and material/phase identification (using XRD). By varying SrTiO₃ content in a standard composite propellant, different compositions were prepared and their performance and processing parameters like the end of mix (EOM) viscosity, mechanical properties, density, burning rate, pressure exponent (n-value), etc. were measured. The results reveal that 2% SrTiO₃ causes more than 12% enhancement in propellant burning rate (at 70 ksc pressure) in comparison to the standard propellant composition. The pressure exponent also increases to 0.46, whereas the standard composition was having its value as 0.35.     

钢丝绳隔振器冲击特性试验研究

采用气缸式冲击模拟台对钢丝绳隔振器进行了冲击特性试验研究,介绍了试验系统及测量方法。在比较符合舰船实际冲击环境的情况下,获得了钢丝绳隔振器压缩和拉伸方向完整的特性曲线。试验结果分析表明,钢丝绳隔振器表现出明显的冲击软化现象,其冲击刚度特性小于静刚度和动刚度,而且它具有大阻尼耗能特性,是比较理想的抗冲元件。