Analysis of some critical aspects in hot machining of Ti-5553 superalloy: Experimental and FE analysis

In this study, a newly developed titanium superalloy, i.e., the Ti-5553 alloy has used for hot machining. This material replaced Ti-grade-5 alloy in the application of aerospace, automobile, and biomedical sector. However, similar to Ti-grade-5 alloy, the Ti-5553 alloy has a low thermal conductivity which makes it difficult-to-cut material categories hence, high tool wear, cutting force and bad surface finish. Hot machining of Ti-5553 has been studied at different machining condition (room and hot) using Deform-2D finite element analysis. The result from the simulation test was compared with the experimental value and reduction of cutting and thrust forces was observed. The experiment was carried out with the same input parameters as simulation, and good coherence between them observed. Additionally, cutting zone temperature, effective stress, etc. for both room and elevated the temperature are also discussed.     

筒形桅杆有限元计算模型及无刚度奇点的消除方法研究

本文提出了一个用于消除空间杆梁结构有限元模型中的无刚度“奇点”的元素及相应的刚度矩阵计算公式。在无刚度“奇点”出现处以此元素替代拉压杆元,可使空间杆梁结构模型中的无刚度“奇点”消失,能够在不增加整个计算模型自由度的情况下提高计算结果的精度。在微型计算机上运用全部三维12自由度梁单元计算模型、拉压杆元——加弹性支座计算模型和本文提出的计算模型对某型军舰的桅杆结构进行了实例计算比较。计算结果表明:用本文方法得到的应力值、位移值与全部三维12自由度梁单元模型的计算结果符合良好。     

应用有限元混合法分析两弹性接触体的动力响应（理论部分）

本文将动力分析中的直接积分法与有限元混合法结合起来对两弹性接触体的摩擦动力求解问题进行了理论分析,推导了有关的有限元公式,设计了计算框图,为计算程序的实现提供了理论依据。     

内可逆卡诺热泵的生态学优化性能

本文导出了内可逆卡诺热泵的供热量、供热率和供热系数的耗散量,以反映热泵供热率π与其耗散φ_cT_Lσ,即热泵熵产率σ、低温热源温度T_L和可逆供热系数φ_c乘积之间最佳折衷的“生态学”性能E=π-φ_cT_Lσ为目标,基于牛顿和线性唯象传热定律,研究内可逆卡诺热泵的优化问题,得到最大E性能时的供热系数界限及相应的供热率和熵产率。     

Q∝T~n时不可逆卡诺热泵的最优性能

非线性传热条件下的内可逆卡诺热机最优性能有了一些讨论,本文将导出不可逆卡诺热泵工作于非线性传热 Q■条件下,最佳供热系数д与泵热率π的关系。据此可确定任意泵热率时所对应的供热系数界限。最后,讨论了这一关系的一些应用,所得结果包含了经典热力学及内可逆线性传热情况下的有关结论,为实际热泵设计提供新的理论依据。     

奇型抛物问题的有限元误差估计

本文引入带权的 Sobolev 空间,讨论了奇型线性问题:(?)((?)u)/((?)t)-1/x~(?)(x~aa(x)u′)′=f(t,x) (x,t)∈1×J(?)/((?)x)u(t,0)=u(t,1)=0 t∈Ju(0,x)=φ(x) x∈I式中 I=(0,1),J=[0,T],0<α<3的有限元方法,并在适当条件下,给出了最佳估计:‖u_(?)-u‖_(0,2,a)≤ch~2{‖φ‖_(2,2,a)+[integral 0 to t (‖u‖~2_(2,2,a)+‖u_(?)‖~2_(2,2,a)dt]~(1/2)}‖u_(?)-u‖_(1,2,a)≤ch~2{‖φ‖_(2,2,a)+[integral 0 to t (‖u‖~2_(2,2,a)+‖u_(?)‖~2_(2,2,a)dt]~(1/2)}     

Analysis of the effect of bore centerline on projectile exit conditions in small arms

Most finite element models of small arms focus on an idealized barrel, typically one with a perfectly straight bore centerline. Using five different experimentally measured bore centerlines, this investigation analyzes the effect centerline nonlinearity has on projectile exit conditions. This includes the effect of rotating a centerline through several orientations. Modeled using Abaqus/Explicit, this dynamic analysis simulates a single firing cycle for each centerline. Projectile jump is calculated for each model as a measure of the effects of warped centerlines. The warped centerlines have a small effect on barrel dynamics.     

计算机辅助加工工件变形分析方法研究

为迅速、准确、合理地确定切削加工的工艺参数 ,将有限元方法、人工神经网络和遗传算法运用于计算机辅助加工工件变形分析中。通过合理的系统设计 ,实现了对工件切削加工变形量的准确预报和对加工参数的正确优化。实际生产证明 ,采用本方法优化确定加工参数 ,达到了预期的迅速、准确、合理的目标 ,有效地降低生产成本 ,提高生产率     

过程速率有限对卡诺制冷机制冷系数与利润率间关系的影响

本文讨论在给定的热源温度和压缩比的情况下,涉及活塞惯性且过程进行的速率有限,只考虑传热不可逆影响的内可逆卡诺制冷机的制冷系数与利润率的关系,得到了一些有意义的结论,为实际制冷机设计提供了一个新的理论依据。