排序方式: 共有112条查询结果,搜索用时 31 毫秒
61.
介绍了阻抗匹配设计原理。自制了三种导电纤维,分别织成正交平纹布,通过优化设计,采用简单层式结构,以酚醛为基体,制备出接近实用水平的多层结构吸波材料。该材料厚3.2mm,密度1.38g/cm3,面密度4.42kg/m2;在8.4GHz~18GHz反射率小于-10dB;弯曲强度173MPa,弯曲模量12.5GPa。 相似文献
62.
纳米粒子复合微米粉体雷达波隐身涂层研究 总被引:8,自引:0,他引:8
采用纳米粒子复合微米吸波粉体方法制备雷达隐身吸波涂层,分别选用纳米Sic、铁酸镍钴和金属钴复合微米羰基铁粉和钴粉。对涂层的雷达波反射率测试结果表明,选用纳米复合方式制成的雷达吸波涂层,有利于展宽吸波带宽或降低峰值反射率,其中用纳米钴复合羰基铁粉涂层最为明显,当定义反射率-频率曲线中小于-5 dB以下的频宽为合格吸波带宽时,纳米钴复合羰基铁粉涂层的最低合格吸波频率可以达到4.8 GHz,较没有纳米复合前有明显降低,对提高吸波涂层的低频段吸波性能作用明显,纳米复合技术为提高吸波涂层的低频吸波性能开辟了新的思路。同时实验也表明纳米复合后对原微米吸波剂吸波性能的改变是不确定的,有的还会使吸波性能变差。因此纳米粉体与微米粉体之间的匹配对吸波性能有较大的影响,这种匹配的关系还有待进一步研究。 相似文献
63.
Chang-gui Song Xiao-dong Li Yue Yang Hui-min Liu Ying-xin Tan Jing-yu Wang 《防务技术》2021,17(6):1936-1943
The core-shell 2,4,6,8,10,12-Hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane/2,4,6-Trinitrotoluene (CL-20/TNT) composite was prepared by spray-drying method in which sensitive high energy explosive (CL-20) was coated with insensitive explosive (TNT). The structure and properties of different formulations of CL-20/TNT composite and CL-20/TNT mixture were characterized by scanning electron microscopy (SEM), Transmission electron microscopy (TEM), Laser particle size analyzer, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), differential scanning calorimetry (DSC), impact sensitivity test and detonation performance. The results of SEM, TEM, XPS and XRD show that ϵ-CL-20 particles are coated by TNT. When the ratio of CL-20/TNT is 75/25, core-shell structure is well formed, and thickness of the shell is about 20–30 nm. And the analysis of heat and impact show that with the increase of TNT content, the TNT coating on the core-shell composite material can not only catalyze the thermal decomposition of core material (CL-20), but also greatly reduce the impact sensitivity. Compared with the CL-20/TNT mixture (75/25) at the same ratio, the characteristic drop height of core-shell CL-20/TNT composite (75/25) increased by 47.6% and the TNT coating can accelerate the nuclear decomposition in the CL-20/TNT composites. Therefore, the preparation of the core-shell composites can be regarded as a unique means, by which the composites are characterized by controllable decomposition rate, high energy and excellent mechanical sensitivity and could be applied to propellants and other fields. 相似文献
64.
Ian G.Crouch 《防务技术》2021,17(6):1887-1894
The ballistic performance, and behaviour, of an armour system is governed by two major sets of variables, geometrical and material. Of these, the consistency of performance, especially against small arms ammunition, will depend upon the consistency of the properties of the constituent materials. In a body armour system for example, fibre diameter, areal density of woven fabric, and bulk density of ceramic are examples of critical parameters and monitoring such parameters will form the backbone of associated quality control procedures. What is often overlooked, because it can fall into the User’s domain, are the interfaces that exist between the various products; the carrier, the Soft Armour Insert (SAI), and the one or two hard armour plates (HAP1 and HAP2). This is especially true if the various products are sourced from different suppliers.There are between 30 and 150 individual layers within a typical body armour system, and each of the interfaces between each of those layers will, in some way or another, contribute to the ballistic performance of the system. For example, consider the following interfaces/interlayers: (i) the frictional, sliding, inter-ply surfaces within a soft armour pack, and also between the pack and the carrier, (ii) the air-gaps that may develop within the soft armour pack, (iii) the interconnecting space between the soft armour pack and the hard armour plate, (iv) the nature of the interfaces between adjacent plies of a multiplied backing laminate, even in a highly compressed Ultra High Molecular Weight Polyethylene (UHMWPE) variant, (v) the interlayer between the ceramic and its substrate, within a HAP, and (vi) the geometrical fit between two hard armour plates within a stacked body armour system. This paper will provide a User-friendly overview of all such interfaces and provide unique guidance as to their criticality and influence. 相似文献
65.
综述了隐身材料的现状和发展趋势,包括雷达隐身材料、光电隐身材料、声隐身材料和降磁材料,并介绍了几种有发展前途的新型隐身材料. 相似文献
66.
67.
本文介绍了满足微带天线使用温度要求的聚合物基复合材料设计的方法与过程。按照这种方法,设计并制造了一批微带天线产品,经高低温测试,证明都符合设计要求。 相似文献
68.
《防务技术》2020,16(2):316-324
This research aims to contribute to the safe methodology for additive manufacturing (AM) of energetic materials. Coating formulation processes were investigated and evaluated to find a suitable method that may enable selective laser sintering (SLS) as the safe method for fabrication of high explosive (HE) compositions. For safety and convenience reasons, the concept demonstration was conducted using inert explosive simulants with properties quasi-similar to the real HE. Coating processes for simulant RDX-based microparticles by means of PCL and 3,4,5-trimethoxybenzaldehyde (as TNT simulant) are reported. These processes were evaluated for uniformity of coating the HE inert simulant particles with binder materials to facilitate the SLS as the adequate binding and fabrication method. Suspension system and single emulsion methods gave required particle near spherical morphology, size and uniform coating. The suspension process appears to be suitable for the SLS of HE mocks and potential formulation methods for active HE composites. The density is estimated to be comparable with the current HE compositions and plastic bonded explosives (PBXs) such as C4 and PE4, produced from traditional methods. The formulation method developed and understanding of the science behind the processes paves the way toward safe SLS of the active HE compositions and may open avenues for further research and development of munitions of the future. 相似文献
69.
从央视新址北配楼火灾着手,通过分析火灾的特点,从加强烟花爆竹安全管理及宣传教育、建筑外部装修消防安全、改进对建筑工程及施工现场的消防监督工作和对高层建筑限高、加强“六熟悉”方面提出了防止类似高层建筑火灾发生的措施。 相似文献
70.
针对管道无损检测问题,阐述了金属磁记忆效应的基本原理,与传统无损检测方式比较,归纳了磁记忆检测的基本特性。在磁记忆检测仪器研发现状的基础上,设计了新型管道磁记忆/漏磁综合检测仪。从检测机理、信号处理和缺陷识别3个方面对检测技术研究现状进行分析和总结。探讨了检测机理的局限性,提出管道磁记忆检测技术的研究新方向。 相似文献