排序方式: 共有69条查询结果,搜索用时 15 毫秒
1.
本文阐述了高速水射流倒空弹体装药的机理,建立了确定水射流引爆炸药的临界速度的模拟实验方法和模型,进行了高速水射流冲击炸药的安全性试验,并对试验结果进行了分析,证明在工作泵压下高速水射流倒空弹体装药安全、可靠。 相似文献
2.
分析了聚能射流的形成过程,并对其中的各阶段进行了详细建模。在模型中考虑了炸药爆轰、金属的驱动、药型罩压垮以及射流和杵体的形成过程。采用该模型对某一聚能装药结构进行了计算,计算结果表明:药型罩顶部和底部微元的压垮速度较小,在射流头部形成反向速度梯度,与试验数据吻合较好。该模型对于多级侵彻战斗部的工程设计与侵彻参数的计算具有一定的参考价值。 相似文献
3.
《防务技术》2020,16(3):720-730
In this research, the effect of the sintering and cooling process on geometry distortion and mechanical properties of PTFE/Al reactive material is investigated. Six particularly selected sintering temperatures, three different cooling modes (annealing cooling, normalizing cooling and rapid cooling), three different initial cooling temperatures, as well as six different final cooling temperatures were designed to compare the effects of sintering temperature, cooling rate, initial cooling temperature and final cooling temperature on the properties of reactive materials. Geometry distortion was quantitatively analyzed by a statistic on the dimensional changes of the specimens and microscopic morphology. A mechanical response properties transition from brittle to ductile was found and analyzed. By combining the thermodynamic properties of PTFE and unsteady heat conduction theory, mechanisms of cooling induced morphology change, temperature induced distortion and strength decrease were obtained. The results showed that the cooling rate has the most significant effect on the morphology transformation, while initial cooling temperature has more significant effect on the dimensional distortion than final cooling temperature. As to the mechanical properties transition from brittle to plastic, a more prominent effect of initial cooling temperature than cooling rate and final temperature was revealed. 相似文献
4.
为了提高风扇外涵和核心机驱动风扇级外涵流体的掺混效率,提出一种采用射流掺混增强的前可调面积引射器设计方案。通过数值模拟的手段对流量特性、流动掺混和总压损失等方面进行了研究,并同基准模型进行了对比分析,结果表明:采用波瓣混合器结构的前可调面积引射器设计,显著地增加了较高出口背压工况下风扇外涵的流通能力;新的设计方案不仅没有增加低出口背压工况下的总压损失,还减小了高背压出口工况下的流动损失;流向涡的特征尺度是提高掺混效率的关键,可以进一步优化波瓣混合器几何轮廓,以满足调节机构对结构设计的要求。 相似文献
5.
《防务技术》2019,15(4):495-505
Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm3 is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance. 相似文献
6.
7.
8.
应用计算流体动力学(CFD)方法分析了一种新型精密抛光技术——磁射流抛光的材料去除机理。磁射流抛光中,含有磨料的磁流变液射流被喷嘴出口附近的局部外加纵向磁场磁化,产生准直的硬化射流束来进行相对远距离的精密抛光。介绍了磁射流抛光的原理和实验装置,分析了磁流变液聚束射流的形成,通过一系列定点抛光实验研究了磁射流抛光工艺的材料去除分布特征,利用计算流体动力学的方法分析了垂直冲击和倾斜冲击情况下,磁流变液射流与工件表面相互作用时径向流场功率密度的分布特征。实验结果和仿真计算结果表明:磁流变液射流在工件表面径向扩展流动产生的径向剪切作用导致了材料去除;CFD方法能模拟抛光区去除率的三维分布,因此可以准确地预测抛光区形状。 相似文献
9.
10.
试验以直接超声方式,在喷射电沉积装置的基础上加载超声设备,分别在20℃和50℃两种镀液温度下在A3钢基体上制备了加载超声和不加载超声Ni镀层,研究了超声波及温度对Ni镀层表面形貌和硬度的影响。试验结果分析表明:在20℃条件下,超声可避免镀层裂纹的产生,提高镀层的硬度;在50℃条件下,超声可细化镀层的组织,且可显著提高镀层硬度;超声波对喷射电沉积层组织和性能的影响机理主要在于超声空化引起的析氢减少、细晶强化和加工硬度。 相似文献