提高聚氨酯推进剂基体粘结强度的途径探索

聚氨酯的水解稳定性较差,粘结强度偏低。将端羟基聚丁二烯与聚氨酯进行共混改性,提高了聚氨酯基体的表观交联度及推进剂的拉伸强度。采用示差扫描量热法和红外光谱法分析基体共混物的微观结构,表明这是提高聚氨酯基体粘结强度的一条有效途径。     

拉压异性材料楔体的极限载荷分析

利用莫尔屈服准则,对一侧承受均布垂直载荷作用的拉压异性材料楔体进行了极限载荷分析。计算结果表明,考虑了材料的拉压异性影响,楔体承受的极限载荷有明显提高。     

机械零件可靠性在应力-强度分布特性下的计算模型

根据应力-强度分布特性下的干涉理论,确定了机械零件在应力-强度诸分布情形下的可靠性计算模型,将应力、强度、结构和可靠性计算联系起来。     

磺化酚醛树脂的研究:对水泥和混凝土抗压强度的影响

研究了磺化酚醛树脂(SPF)对水泥和混凝土抗压强度的影响,结果显示:掺入SPF后,水泥和混凝土不同龄期的抗压强度均有明显的提高并且依赖于掺量、硫酸钠含量以及磺化剂用量.     

挠性接管在轴对称载荷下的应力应变计算

针对目前挠性接管强度计算存在的不足,在充分考虑骨架层的弯曲刚度和扭转刚度对挠性接管强度影响的基础上,推导出在承受轴对称负荷(拉压、扭矩及内压)时,挠性接管及其加强筋的应变和外力的关系,为挠性接管的结构设计和强度计算提供了理论公式.     

Development of proxy relationships: a case study of the Lebanese Civil War

Proxy warfare is a consistent element in international warfare. However, it is unclear why proxy relationships form in cases where states have multiple options of groups to support. Existing research identifies the presence of transnational constituencies, shared interstate rivalries, and moderate relative strength of militant groups as highly influential on the development of a proxy relationship. This study examines the presence of these variables within the context of the Lebanese Civil War. The results of this demonstrate that each state places greater importance on some variables and ignores others when choosing a proxy. Additionally, this study further demonstrates the presence of new variables that are key to the development of proxy relationships.     

【专栏】飞机结构静强度应变现场测试手段展望

目前飞机结构静强度应变现场主要的测试手段为使用电阻应变计测量系统,但电阻应变计测量系统存在抗电磁干扰差、引线过多以及一致性难以保证等问题,测试效果难以保证。近年来,光纤传感以及非接触光学测量手段的迅速发展,为飞机结构静强度应变现场测试提供了多种选择。本文通过分析以数字图像相关法技术为代表的新技术的特点,如通过进行非接触操作消除安装过程中所带来的分散性误差以及不确定性,在应对某些需要定性分析的飞机静强度试验场合时可以实时给出三维应变和位移场数据,使测量技术更加直观,以及可溯源性更好、更容易保证计量特性的稳定等,对未来飞机结构静强度应变现场测试手段进行了展望,以期为相关部门和机构提供参考。     

Enhancing the explosive characteristics of a Semtex explosive by involving admixtures of BCHMX and HMX

A well-known ternary plastic explosive, Czech Semtex 1H, contains a mixture of PETN and RDX softened by SBR. In this work, BCHMX was used to replace PETN in Semtex 1H to form Sem-BC+RDX. In addition, another mixture based on BCHMX and HMX as energetic fillers bonded by the polymeric matrix of Semtex 1H (Sem-BC+HMX) was studied. The particle size distribution of each individual explosive was determined to obtain the optimum mixing conditions. Friction and impact sensitivities were determined. The velocity of detonation was reported practically and the detonation properties were calculated by EXPLO5 code. The explosive strength of each sample was measured by the ballistic mortar test. The conclusion confirms that the velocity of detonation of Sem-BC+HMX was the highest in comparison with the prepared samples. Sem-BC+RDX has the least impact and frictions sensitivities. Sem-BC+RDX has higher detonation velocity, detonation properties and explosive strength than Semtex 1H. Addition of BCHMX in Semtex 1H as a replacement for PETN is the candidate to produce a high performance advanced Czech plastic explosive.     

炮闩闩体击针孔强度仿真计算与结构改进

从击针和闩体的装配结构关系入手,在闩体击针室受力分析的基础上,进行了闩体有限元分析,得到了击针室两个不同部位受力时闩体击针孔处的应力和应变情况,从而提出解决闩体镜面击针孔产生凸出或裂纹问题的可行方案。     

磨损身管下的杆式穿甲弹强度失效计算机模拟

针对某型105 mm钨合金超速脱壳穿甲弹在射击试验时出现的弹体强度失效现象,使用有限元分析软件对其强度进行了分析计算。计算分两种工况：正常状态下的弹体应力应变分布和磨损身管条件下的弹体应力应变分布。根据计算结果,证实了弹体强度失效是由于火炮身管过度磨损的原因所致。