电磁脉冲对高频结构的热效应分析

对于Cerenkov型器件,由高频结构温升引发的热脱附会造成的射频击穿,进而导致输出功率降低和脉冲缩短。基于此,研究了电磁脉冲对高频结构的加热温升效应,推导了高频结构的温升公式,指出了理论公式的适用范围,并给出了数值求解试件温升的方法。以二周期1 MV·cm^-1的高频结构为例,进行了温升的数值计算和仿真研究。结果表明,脉宽100 ns的单脉冲对不锈钢试件的温升效应明显高于其他材料。当系统工作在高重频时,电磁脉冲的温升作用可能使金属材料达到气体脱附的阈值从而引发气体脱附形成局部高压。该研究可为高功率微波源中的气体脱附以及射频击穿等研究提供参考。     

Many‐server loss models with non‐poisson time‐varying arrivals

This article proposes an approximation for the blocking probability in a many‐server loss model with a non‐Poisson time‐varying arrival process and flexible staffing (number of servers) and shows that it can be used to set staffing levels to stabilize the time‐varying blocking probability at a target level. Because the blocking probabilities necessarily change dramatically after each staffing change, we randomize the time of each staffing change about the planned time. We apply simulation to show that (i) the blocking probabilities cannot be stabilized without some form of randomization, (ii) the new staffing algorithm with randomiation can stabilize blocking probabilities at target levels and (iii) the required staffing can be quite different when the Poisson assumption is dropped. © 2017 Wiley Periodicals, Inc. Naval Research Logistics 64: 177–202, 2017     

Driving force coordinated control of an 8 ×8 in-wheel motor drive vehicle with tire-road friction coefficient identification

Because of the complexities of tire-road interaction,the wheels of a multi-wheel distributed electric drive vehicle can easily slip under certain working conditions.As wheel slip affects the dynamic per-formance and stability of the vehicle,it is crucial to control it and coordinate the driving force.With this aim,this paper presents a driving force coordination control strategy with road identification for eight-wheeled electric vehicles equipped with an in-wheel motor for each wheel.In the proposed control strategy,the road identification module estimates tire-road forces using an unscented Kalman filter al-gorithm and recognizes the road adhesion coefficient by employing the recursive least-square method.According to road identification,the optimal slip ratio under the current driving condition is obtained,and a controller based on sliding mode control with a conditional integrator uses this value for accel-eration slip regulation.The anti-slip controller obtains the adjusting torque,which is integrated with the driver-command-based feedforward control torque to implement driving force coordination control.The results of hardware-in-loop simulation show that this control strategy can accurately estimate tire-road forces as well as the friction coefficient,and thus,can effectively fulfill the purpose of driving force coordinated control under different driving conditions.     

Optimization of process parameters of the activated tungsten inert gas welding for aspect ratio of UNS S32205 duplex stainless steel welds

The activated TIG (ATIG) welding process mainly focuses on increasing the depth of penetration and the reduction in the width of weld bead has not been paid much attention. The shape of a weld in terms of its width-to-depth ratio known as aspect ratio has a marked influence on its solidification cracking tendency. The major influencing ATIG welding parameters, such as electrode gap, travel speed, current and voltage, that aid in controlling the aspect ratio of DSS joints, must be optimized to obtain desirable aspect ratio for DSS joints. Hence in this study, the above parameters of ATIG welding for aspect ratio of ASTM/UNS S32205 DSS welds are optimized by using Taguchi orthogonal array (OA) experimental design and other statistical tools such as Analysis of Variance (ANOVA) and Pooled ANOVA techniques. The optimum process parameters are found to be 1 mm electrode gap, 130 mm/min travel speed, 140 A current and 12 V voltage. The aspect ratio and the ferrite content for the DSS joints fabricated using the optimized ATIG parameters are found to be well within the acceptable range and there is no macroscopically evident solidification cracking.     

一种鱼雷自导信号频率检测方法研究

靶场在进行智能鱼雷鉴定试验任务时,实时准确地检测出鱼雷自导信号的频率成分是靶标信号处理中的重要环节,谱线比值法便是靶标进行信号处理时检测信号频率的一种有效方法。本文介绍了谱线比值法的基本原理,针对目前鱼雷自导信号特点,对该方法提出了改进方案并进行了仿真。仿真结果表明,经改进的谱线比值法能够满足靶标检测复杂鱼雷自导信号体制下信号频率的使用要求。     

数值模拟气/气喷嘴速度比对燃烧性能的影响

为研究应用于全流量补燃循环发动机的不同气/气喷嘴得到的燃烧流场,通过求解NavierStokes方程组,对不同燃料与氧化剂速度比下的流动燃烧过程进行了数值计算,计算结果与实验结果吻合。仿真结果表明:增加速度比能使燃烧火焰面提前,燃烧效率变大。如果发动机的长度受到限制,可以适当增加速度比以实现高效燃烧。     

卫星导航接收机中积分清零器的性能分析

为了使跟踪环路得到最高的输入信噪比,卫星导航接收机在时延估计时应使用匹配滤波器。但出于节省硬件资源的考虑,卫星导航接收机通常采用积分清零器完成相关运算。然而积分清零器相对于匹配滤波器存在性能损耗,对此目前尚无量化的结论。本文推导出积分清零器性能损耗的解析表达式,并使用Monte Carlo仿真的方法验证结论的正确性。理论和仿真结果表明当采样率为2倍的前端带宽时,积分清零器相比匹配滤波存在约0.44dB的损耗,当采样率提高到4倍信号带宽时,积分清零器的性能损耗几乎可以忽略。该结论对卫星导航接收机的设计具有重要的意义。     

阶比谱分析与汽车起动电机故障的实时诊断

本文主要论述阶比谱分析方法及其在汽车起动电机故障实时诊断中的应用。首先阐述了阶比谱分析的原理以及阶比采样中混迭与泄漏的产生及其抑制方法,然后讨论了如何在起动电机运行过程短、升速快的情况下获取感兴趣的噪声信号,进而采用阶比谱分析方法从信号中提取故障特征信息,最后利用阀值判别法起动电机的故障进行实时诊断。     

Effects of total pressures and equivalence ratios on kerosene/air rotating detonation engines using a paralleling CE/SE method

In this paper, the kerosene/air rotating detonation engines(RDE) are numerically investigated, and the emphasis is laid on the effects of total pressures and equivalence ratios on the operation characteristics of RDE including the initiation, instabilities, and propulsive performance. A hybrid MPI + OpenMP parallel computing model is applied and it is proved to be able to obtain a more effective parallel performance on high performance computing(HPC) systems. A series of cases with the total pressure of 1 MPa, 1.5 MPa, 2 MPa, and the equivalence ratio of 0.9, 1, 1.4 are simulated. On one hand, the total pressure shows a significant impact on the instabilities of rotating detonation waves. The instability phenomenon is observed in cases with low total pressure (1 MPa) and weakened with the increase of the total pressure. The total pressure has a small impact on the detonation wave velocity and the specific impulse. On the other hand, the equivalence ratio shows a negligible influence on the instabilities, while it affects the ignition process and accounts for the detonation velocity deficit. It is more difficult to initiate rotating detonation waves directly in the lean fuel operation condition. Little difference was observed in the thrust with different equivalence ratios of 0.9, 1, and 1.4. The highest specific impulse was obtained in the lean fuel cases, which is around 2700 s. The findings could provide insights into the understanding of the operation characteristics of kerosene/air RDE.     

Research on fuze microswitch based on corona discharge effect

Abnormal voltages such as electrostatic, constant current, and strong electromagnetic signals can erro-neously trigger operation of MEMS pyrotechnics and control systems in a fuze, which may result in casualties. This study designs a solid-state micro-scale switch by combining the corona gas discharge theory of asymmetric electric fields and Peek's Law. The MEMS switch can be transferred from "off" to"on" through the gas breakdown between the corona electrodes. In the model, one of the two electrodes is spherical and the other flat, so a non-uniform electric field is formed around the electrodes. The theoretical work is as follows. First, the relation among the radius of curvature of the spherical electrode, the discharge gap, and the air breakdown voltage is obtained; to meet the low voltage (30-60 V) required to drive the MEMS switch, the radius of curvature of the spherical electrode needs to be 10-50 μm and the discharge gap between the two electrodes needs to be 9-11 μm. Second, the optimal ratio ε is introduced to parameterize the model. Finally, the corona discharge structural parameters are determined by comparing the theoretical and electric field simulation results. The switch is then fabricated via MEMS processing. A hardware test platform is built and the performing chip tested. It is found that when the electrode gap is 9 μm, the electrostatic voltage is at least 37.3 V, with an error of 2.6% between the actual and theoretical air breakdown voltages. When the electrode gap is 11 μm, the electrostatic voltage is at least 42.3 V, with an error of 10.5% between the actual and theoretical air breakdown voltages. Both cases meet the design requirements.