铅基合金中锡量测定方法研究

试样用硫酸溶解,盐酸酸化,使Pb2 沉淀为PbSO4,Sb3 水解沉淀为SbOC l,Ag 沉淀为AgC l除去。在0.6mol/L硫酸溶液中,锡与苯芴酮-溴化十六烷基三甲铵生成有色络合物,于波长510nm处测量吸光度。对于残余微量的锑、铁的干扰,可加入酒石酸、高锰酸钾和抗坏血酸消除。该方法条件易控制、稳定、准确,对锡量在0.01~1(%)测定较为优越。     

Multifunctional A356 alloy/ PKSAnp composites: Microstructure and mechanical properties

Mechanical properties and microstructure of multifunctional composites produced with palm kernel shell ash nanoparticle (PKSAnp)-A356 alloy composites was studied. The composites were produced using Double layer feeding stir casting method (DLF-SCM) by adding 1 wt%‒4 wt.% PKSAnp. The microstructure, density, electrical and mechanical properties were determined. The results shows that there was a uniform distribution of the PKSAnp in A356 alloy. The mismatch at the interface between the PKSAnp and A356 alloy was 4.26%. Improvement of 30.47%, 41.91%, 49.52%, 40.90% and 65.09% were obtained for hardness values, tensile, yield strength, %elongation and impact energy at 4 wt% PKASnp. The work has established that the developed composites can be used for multifunctional applications where combination of toughness and strength is vital.     

Effect of fusion welding processes on tensile properties of armor grade,high thickness,non-heat treatable aluminium alloy joints

AA5059 is one of the high strength armor grade aluminium alloy that finds its applications in the military vehicles due to the higher resistance against the armor piercing (AP) threats. This study aimed at finding the best suitable process among the fusion welding processes such as gas tungsten arc welding (GTAW) and gas metal arc welding (GMAW) by evaluating the tensile properties of AA5059 aluminium alloy joints. The fracture path was identified by mapping the low hardness distribution profile (LHDP) across the weld cross section under tensile loading. Optical and scanning electron microscopies were used to characterize the microstructural features of the welded joints at various zones. It is evident from the results that GTAW joints showed superior tensile properties compared to GMAW joints and this is primarily owing to the presence of finer grains in the weld metal zone (WMZ) and narrow heat-affected zone (HAZ). The lower heat input associated with the GTAW process effectively reduced the size of the WMZ and HAZ compared to GMAW process. Lower heat input of GTAW process results in faster cooling rate which hinders the grain growth and reduces the evaporation of magnesium in weld metal compared to GMAW joints. The fracture surface of GTAW joint consists of more dimples than GMAW joints which is an indication that the GTAW joint possess improved ductility than GMAW joint.     

氮气保护法在微细铝粉生产中的应用

雾化空气法生产微细铝粉已有近 70年历史 ,但其生产过程极易发生爆炸 ,氮气由于其良好的防火性能 ,在生产中代替空气将会极大降低爆炸的可能性。     

Thomas Firth and Sons – Steelmakers to the Arms Industries. Part 2: Heavy Armaments

Firth’s were the first of the Sheffield steel makers to enter the field armaments. Their involvement with Colt has been outlined in an article in the journal of the Colt Collectors Association in America and their activities as steelmakers to the small-arms industries has been covered in a previous issue of this Journal. This article gives a brief overview of their involvement as manufacturers in the field of heavy armaments, being the first to make all-steel guns and their evolving role in the use of steel for ordnance, culminating in the displacement of wrought iron by the adoption of steel for ordnance manufacture by the Royal Gun Factory in the 1880s. It also highlights their development of stainless steel in this context.     

两栖车辆用牺牲阳极材料研究进展

结合两栖车辆的发展和两栖车辆牺牲阳极阴极保护性能指标要求,介绍了两栖车辆用牺牲阳极材料研究进展,分析了主要合金元素作用机理。根据牺牲阳极耐干湿交替性能要求和实车试验结果,采用极化时间、车体保护电位、活化性能等技术指标,评价了五元和六元牺牲阳极对两栖车辆阴极保护效果。展望了两栖车辆牺牲阳极阴极保护研究的下一步工作方向和重点。     

2A12铝合金焊接接头超声冲击处理前后拉伸性能分析

为克服铝合金薄板焊接接头强度偏低、韧性不足的缺点,用ER5356焊丝对不同厚度的2A12铝合金板材进行了手工氩弧焊接,并采用超声冲击处理对焊接接头进行全覆盖强化处理。采用金相显微镜观察了处理和未处理焊接接头的显微组织结构,对接头的力学性能进行了测试分析,分析了超声冲击处理改善2A12铝合金焊接接头力学性能的机理。结果表明：铝合金焊接接头经超声冲击强化处理后,6 mm和4 mm厚板材对接接头的抗拉强度分别提高了17.4%和23.7%,延伸率分别提高了28%和44%,焊缝表层组织得到明显细化。分析认为：晶粒大幅细化、组织致密化和缺陷减少,是超声冲击处理改善铝合金焊接接头抗拉伸性能的主要原因。     

储氢电极合金的温度特性研究

针对目前储氢电极合金不适用于电动汽车用大型电池的情况 ,以Ml (NiCoMnTi) 5 合金为例 ,系统研究了温度对储氢电极合金电化学性能的影响。结果表明 :随着温度升高 ,合金的放电容量降低 ,循环稳定性恶化 ,自放电加剧 ;但是在高温下合金的高倍率放电特性得到显著改善。     

磁性合金A1-xBx相图的理论计算

采用变分累积展开方法,研究了块体磁性合金的相图.利用随机键海森堡模型计算了面心立方、体心立方的居里点和耐尔点,给出了磁性合金临界点的计算公式,进而分别给出自旋1/2和3/2情况下Tc-x相图,并加以分析.     

Tuning the reactivity of Al–Ni by fine coating of halogen-containing energetic composites

In this paper, various core-shell structured Al–Ni@ECs composites have been prepared by a spray-drying technique. The involved ECs refer to the energetic composites (ECs) of ammonium perchlorate/nitrocellulose (AP/NC, NA) and polyvinylidene fluoride/hexanitrohexaazaisowurtzitane (PVDF/CL-20, PC). Two Al–Ni mixtures were prepared at atomic ratios of 1:1 and 1:3 and named as Al/Ni and Al/3Ni, respectively. The thermal reactivity and combustion behaviors of Al–Ni@ECs composites have been comprehensively investigated. Results showed that the reactivity and combustion performance of Al–Ni could be enhanced by introducing both NA and PC energetic composites. Among which the Al/Ni@NA composite exhibited higher reactivity and improved combustion performance. The measured flame propagation rate (v = 20.6 mm/s), average combustion wave temperature (T_max = 1567.0 °C) and maximum temperature rise rate (γ_t = 1633.6 °C/s) of Al/Ni@NA are higher than that of the Al/Ni (v = 15.8 mm/s, T_max = 858.0 °C, and γ_t = 143.5 °C/s). The enhancement in combustion properties could be due to presence of the acidic gaseous products from ECs, which could etch the Al₂O₃ shell on the surface of Al particles, and make the inner active Al to be easier transported, so that an intimate and faster intermetallic reaction between Al and Ni would be realized. Furthermore, the morphologies and chemical compositions of the condensed combustion products (CCPs) of Al–Ni@ECs composites were found to be different depending on the types of ECs. The compositions of CCPs are dominated with the Al–Ni intermetallics, combining with a trace amount of Al₅O₆N and Al₂O₃.