排序方式: 共有114条查询结果,搜索用时 46 毫秒
101.
为研究球形头部弹丸高速侵彻运动靶板的侵彻规律,运用LS-DYNA动力分析软件仿真研究了不同条件下球形头部弹丸对靶板的正侵彻效应,获得了运动靶板厚度、材料和弹丸着速3种参数对侵彻过程中弹丸弹道偏移、翻转角度和剩余速度的响应规律。结果表明,随着着速的提高,弹丸翻转幅度和弹道偏移量逐渐减小;随着靶板厚度的增加,弹丸正向翻转角度和轴向剩余速度显著减小,而弹道偏移量增大;3种材料运动靶板中,4340钢靶对弹丸弹道偏移、翻转角度和剩余速度的影响最大,Weldox460钢次之,LY12铝最小。 相似文献
102.
为了研究钻地武器的侵彻性能,在57mm口径的气炮上发射长杆射弹对三种靶体进行模拟侵彻实验。靶体为水泥砂浆石靶、钢纤维混凝土靶和含单层密排刚玉球的钢纤维混凝土靶。实验结果表明,弹头形状对侵彻深度有明显影响;当长杆射弹和撞击速度都相同时,与侵彻钢纤维混凝土靶相比,含单层密排刚玉球的钢纤维混凝土靶中的侵彻深度大约降低了11%,而水泥砂浆石靶中的侵彻深度增加了12%。 相似文献
103.
Enhanced damage to the full-filled fuel tank,impacted by the cold pressed and sintered PTFE/AL/W reactive material projectile(RMP)with a density of 7.8 g/cm3,is investigated experimentally and theoretically.The fuel tank is a rectangular structure,welded by six pieces of 2024 aluminum plate with a thickness of 6 mm,and filled with RP-3 aviation kerosene.Experimental results show that the kerosene is ignited by the RMP impact at a velocity above 1062 m/s,and a novel interior ignition phenomenon which is closely related to the rupture effect of the fuel tank is observed.However,the traditional steel projectile with the same mass and dimension requires a velocity up to 1649 m/s to ignite the kerosene.Based on the experimental results,the radial pressure field is considered to be the main reason for the shear failure of weld.For mechanism considerations,the chemical energy released by the RMP enhances the hydrodynamic ram(HRAM)effect and provides additional ignition sources inside the fuel tank,thereby enhancing both rupture and ignition effects.Moreover,to further understand the enhanced ignition effect of RMP,the reactive debris temperature inside the kerosene is analyzed theoretically.The initiated reactive debris with high temperature provides effective interior ignition sources to ignite the kerosene,resulting in the enhanced ignition of the kerosene. 相似文献
104.
Changing and optimizing the projectile nose shape is an important way to achieve specific ballistic performance. One special ballistic performance is the embedding effect, which can achieve a delayed high-explosive reaction on the target surface. This embedding effect includes a rebound phase that is significantly different from the traditional penetration process. To better study embedment behavior, this study proposed a novel nose shape called an annular grooved projectile and defined its interaction process with the ductile metal plate as partial penetration. Specifically, we conducted a series of low-velocity-ballistic tests in which these steel projectiles were used to strike 16-mm-thick target plates made with 2024-O aluminum alloy. We observed the dynamic evolution characteristics of this aluminum alloy near the impact craters and analyzed these characteristics by corresponding cross-sectional views and numerical simulations. The results indicated that the penetration resistance had a brief decrease that was influenced by its groove structure, but then it increased significantly-that is, the fluctuation of penetration resistance was affected by the irregular nose shape. Moreover, we visualized the distribution of the material in the groove and its inflow process through the rheology lines in microscopic tests and the highlighted mesh lines in simulations. The combination of these phenomena revealed the embed-ment mechanism of the annular grooved projectile and optimized the design of the groove shape to achieve a more firm embedment performance. The embedment was achieved primarily by the target material filled in the groove structure. Therefore, preventing the shear failure that occurred on the filling material was key to achieving this embedding effect. 相似文献
105.
以多爆炸成型弹丸(MEFP)为计算模型,应用显式有限元程序LS-DYNA,分析了药型罩间距、锥角、壁厚、装药高度和装药直径5种因素对MEFP发散角的影响规律。结果表明:随着药型罩间距、壁厚和装药直径的增加以及药型罩锥角、装药高度的减小,MEFP的发散角在减小。在此基础上以MEFP发散角为命中和毁伤概率指标,应用正交优化方法针对5种结构因素对MEFP发散角的影响主次关系进行了分析研究。结果表明药型罩壁厚是MEFP战斗部命中和毁伤概率的主要影响因素,并得到了5种结构因素各水平的最优组合。 相似文献
106.
107.
108.
109.
110.
采用 IBM- PC机为主机 ,对弹丸动不平衡量 (m1 ,m2 )及相位角α进行自动测试并做相应的数据处理。设计了弹丸左、右两标定面的平面分离电路、A/D转换电路等。 相似文献