基于CREAM的后方仓库叉车装卸运输弹药HRA评估

针对我军后方仓库弹药装卸运输环节对人员叉车操作的安全性需求,设计出了叉车操作测试场地路线,归纳总结了人员操作叉车进行弹药装卸运输环节中的安全失效形式及失效原因,构建了HRA评估数学模型．选取我军某后方仓库搬运机械建制班人员为对象,进行了实地测试,得到了弹药装卸运输环节的人为失误概率．测试结果表明,基于CREAM方法能够较好地解决后方仓库弹药装卸运输环节人为失误概率的量化问题．     

基于自适应阈值的FAST特征点提取算法

FAST特征提取算法阈值选取固定,因此不能满足不同图像的特征点抽取要求,并且提取的结果存在着多个特征点块的现象。针对这些缺陷,首先采用动态全局阈值对原始灰度图像进行初步提取得到候选特征点,然后采取动态局部阈值和非极大值抑制法进一步对候选特征点进行筛选,从而达到自适应选取阈值和抑制多个特征点块的目的。实验表明,改进后的算法稳定性高,对不同光照和对比度情况下有一定的适应能力,并且运算量相对比于其他一些特征提取算法要小得多,满足实时应用的要求。     

内编队地球重力场测量性能数值分析

内编队系统通过实现内卫星纯引力轨道环境和内卫星精密定轨,完成高精度地球重力场测量,实现了不依赖于加速度计的重力卫星实施新途径。针对内编队重力场测量性能难以解析分析的情况,基于MATLAB并行程序设计进行了重力场测量数值模拟,获得了内编队重力场测量的有效阶数及其精度。在内编队轨道高度为300km、内卫星干扰力为1.0×10-10m/s2、外卫星定轨精度为3cm、内外卫星相对状态测量精度为1mm的条件下,计算得到内编队测量重力场的有效阶数为72,相应的大地水准面累积误差为44cm,重力异常累积误差为4.5mGal,由此可知内编队测量重力场的有效阶数主要分布在低阶部分。     

Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Formation of adiabatic shearing band for high-strength Ti-5553 alloy: A dramatic thermoplastic microstructural evolution

By using split Hopkinson pressure bar, optical microscopy and electronic microscopy, we investigate the influence of initial microstructures on the adiabatic shear behavior of high-strength Ti–5Al–5V–5Mo–3Cr (Ti-5553) alloy with lamellar microstructure and bimodal microstructure. Lamellar alloy tends to form adiabatic shearing band (ASB) at low compression strain, while bimodal alloy is considerably ASB-resistant. Comparing with the initial microstructure of Ti-5553 alloy, we find that the microstructure of the ASB changes dramatically. Adiabatic shear of lamellar Ti-5553 alloy not only results in the formation of recrystallized β nano-grains within the ASB, but also leads to the chemical redistribution of the alloying elements such as Al, V, Cr and Mo. As a result, the alloying elements distribute evenly in the ASB. In contrast, the dramatic adiabatic shear of bimodal alloy might give rise to the complete lamination of the globular primary α grain and the equiaxial prior β grain, which is accompanied by the dynamic recrystallization of α lamellae and β lamellae. As a result, ASB of bimodal alloy is composed of α/β nano-multilayers. Chemical redistribution does not occur in ASB of bimodal alloy. Bimodal Ti-5553 alloy should be a promising candidate for high performance armors with high mass efficiency due to the processes high dynamic flow stress and excellent ASB-resistance.     

引入块内码元频数抽样的块内频数检测识别方案

为识别链路层比特流是否加密,以未加密与加密数据在随机统计特性上的差异为依据,利用随机性检测的方法对加密比特流进行识别.在不同比特流长度条件下对3种典型随机性检测方法的识别率进行了比较研究.针对3种检测方法均对长度较短的未加密比特流识别率较低的问题,在块内频数检测的基础上,提出了基于块内码元频数抽样的比特流预处理方案,以及块内频数检测最优分块长度选择方案,并对预处理方案对识别率的影响进行了分析.实验结果表明,提出的方案可以显著提高块内频数检测对未加密比特流的识别率.     

新型舰炮使用测速雷达后观测距离偏差射击校正方法

针对测速雷达精确校正初速后的观测距离偏差校正方法进行研究,建立不同校正方法校正量计算模型,对比分析不同校正方法校正精度,得出了使用测速雷达精确校正初速后观测距离偏差应采用折合空气密度校正精度高的结论,为中大口径舰炮部队作战与训练和装备的研制改进提供依据。     

精密磨床主轴回转误差补偿技术的研究

本文在分析精密磨床主轴回转误差运动特点的基础上,提出了基于时序建模理论的随机运动误差补偿方案,并介绍了采用信号处理器TMS32010实现高速补偿控制的方法及初步实验结果。     

速率陀螺解相遇与敌我态势的关系

根据敌我相对运动的原理,导出速率陀螺测量出的目标俯仰角速度Ω_s、测向角速度Ω_L 和探测器测出的距变率与敌我姿势要素间的关系,提出了距变率在极短时间内保持不变的条件;并利用Ω_s、Ω_L 和有关数据(qw,ε、D、■、V_w、K_w)推导出在不满足“快解”条件时计算目标运动要素和弹丸发射诸元的计算公式。     

核安全保护装置温漂性能改进的实验研究

核动力系统中,安全保护装置的温度漂移是一直存在的,它不仅影响整个控制系统的安全,而且影响该装置中各插件板的互换性。本文针对这一实际问题,在实验室用实际单元插件模拟现场温度变化的过程中,进行了参数测试。通过对电路及测试数据的分析,找出了问题所在,提出了改进措施。通过对改进前后测试数据的对比,证明改进之后性能有非常明显的提高。