酚醛-石英混杂纤维增强苯并噁嗪复合材料高温失效特征

通过模压工艺制备了酚醛-石英混织纤维增强苯并噁嗪复合材料(P-Q/BZ)试样,考察了其力学性能、烧蚀性能和耐冲刷性能,分析了该试样在高温环境中的主要失效特征,研究其在高温环境中的适用性。结果表明,未经热处理的P-Q/BZ试样平均弯曲强度、弯曲模量和层间剪切强度分别为283 MPa、10.8 GPa和22.6 MPa;经300℃,N_2处理15 min后,试样均匀膨胀,厚度增加22%,弯曲强度、弯曲模量和层间剪切强度分别下降58%、41%和58%;在氧乙炔焰的平均质量烧蚀率和线烧蚀率分别为0.048 4 g/s和-0.081 mm/s,烧蚀后试样宏观不分层,表面炭层微观分层严重,酚醛纤维热解炭、树脂基体热解炭、熔融石英纤维以及碳硅氧化产物相互分离;该试样耐冲刷能力差,在发动机尾焰烧蚀平台模拟的热-力耦合环境中的质量损失率高达59%。P-Q/BZ复合材料需要解决热解膨胀问题,进一步提高抗冲刷性能。     

Multifunctional A356 alloy/ PKSAnp composites: Microstructure and mechanical properties

Mechanical properties and microstructure of multifunctional composites produced with palm kernel shell ash nanoparticle (PKSAnp)-A356 alloy composites was studied. The composites were produced using Double layer feeding stir casting method (DLF-SCM) by adding 1 wt%‒4 wt.% PKSAnp. The microstructure, density, electrical and mechanical properties were determined. The results shows that there was a uniform distribution of the PKSAnp in A356 alloy. The mismatch at the interface between the PKSAnp and A356 alloy was 4.26%. Improvement of 30.47%, 41.91%, 49.52%, 40.90% and 65.09% were obtained for hardness values, tensile, yield strength, %elongation and impact energy at 4 wt% PKASnp. The work has established that the developed composites can be used for multifunctional applications where combination of toughness and strength is vital.     

SiO2气凝胶复合短切莫来石纤维多孔骨架复合材料的制备及性能

将短切莫来石纤维、硅溶胶、B4C粉,经过1260℃烧结制备多孔骨架,以正硅酸乙酯、去离子水和乙醇配制SiO2溶胶,并将多孔骨架与SiO2溶胶浸渍,经过超临界干燥制备SiO2气凝胶复合的莫来石隔热瓦.通过热重和差热分析、X射线能谱分析,表明B4C在700℃～900℃时发生氧化,生成B2O3将短切纤维粘接到一起,莫来石多孔骨架在1500℃以下稳定存在.具有纳米级孔洞结构的SiO2气凝胶填充了多孔骨架的微米级孔洞,隔热瓦的热导率在200℃、500℃、800℃、1000℃分别下降了44.3%、33.8%、34.6%、29.5%.此外,SiO2气凝胶的复合使得抗弯和抗压强度分别提高了50%和40%.     

碳化硼涂覆的碳纤维的抗热氧化性研究

用自己合成的裂解能得到碳化硼的聚碳硼烷,对碳纤维进行涂层,并详细测试了涂层碳纤维的抗热氧化性能。     

UHMWPE纤维混凝土基本力学性能研究

研究了一种由超高分子量聚乙烯（UHMWPE）纤维增强的新型纤维混凝土基本力学性能。针对C70等级高强混凝土,设计了四种体积掺量纤维混凝土,通过立方体抗压、劈裂抗拉和四点弯曲抗折试验,分析了纤维掺量对混凝土力学性能的影响。结果表明：UHMWPE纤维对混凝土的抗压强度增强作用不明显,但较大提高了混凝土的抗拉强度和抗折强度,且对混凝土有很好的阻裂、增韧效果。在纤维体积掺量为0.3%~0.5%时,劈裂抗拉强度提高25%以上;掺量0.5%时,弯曲抗折强度提高率超过23%。     

纳米二氧化硅增强硬质聚氨酯泡沫塑料的制备

采用功率超声,将纳米二氧化硅颗粒分散到多次甲基多苯基多异氰酸酯体系内,然后与聚醚多元醇聚合制得了纳米二氧化硅增强的硬质聚氨酯泡沫塑料。SEM分析表明,纳米二氧化硅均匀分散在聚氨酯泡沫中。在较低添加量时,纳米二氧化硅使压缩强度和冲击强度有一定提高,但会引起多次甲基多苯基多异氰酸酯粘度迅速增加,从而导致发泡反应困难,当添加量为7wt%时,压缩强度和冲击强度开始下降。     

Mechanical behavior and failure mechanism of polyurea nanocomposites under quasi-static and dynamic compressive loading

Polyurea is an elastomeric material that can be applied to enhance the protection ability of structures under blast and impact loading.In order to study the compressive mechanical properties of SiC/polyurea nanocomposites under quasi-static and dynamic loading,a universal testing machine and split Hop-kinson pressure bar(SHPB)apparatus were used respectively.The stress-strain curves were obtained on polyurea and its composites at strain rates of 0.001-8000 s-1.The results of the experiment suggested that increase in the strain rates led to the rise of the flow stress,compressive strength,strain rate sensitivity and strain energy.This indicates that all of the presented materials were dependent on strain rate.Moreover,these mechanical characters were enhanced by incorporating a small amount of SiC into polyurea matrix.The relation between yield stress and strain rates were established using the power law functions.Finally,in order to investigate the fracture surfaces and inside information of failed specimens,scanning electron microscopy(SEM)and micro X-ray computed tomography(micro-CT)were used respectively.Multiple voids,crazes,micro-cracks and cracking were observed in fracture surfaces.On the other hand,the cracking propagation was found in the micro-CT slice images.It is essential to understand the deformation and failure mechanisms in all the polyurea materials.     

Ni-Zn铁氧体粉末的溶胶-凝胶合成及微波性能

以硝酸铁、硝酸镍、硝酸锌、柠檬酸和氨水为原料,用溶胶-凝胶法合成了不同组成的Ni-Zn铁氧体粉末。利用热分析、X射线衍射等手段研究了干凝胶热分解行为。利用网络分析仪对铁氧体粉末的电磁性能进行了表征,考察了铁氧体的组成与其电磁性能之间的关系。结果表明,溶胶-凝胶法合成的铁氧体粉末的μ″值随测试频率的提高和Ni-Zn铁氧体中锌含量的增加而减小。     

几何内蕴量对拉伸模具工作面力学性能的影响

曲率、度规不变量、凸凹性等几何内蕴量的不均匀分布直接影响模具的力学性能。本文研究了曲率与变形能、曲率与摩擦耗损功、度规不变量与热辐射、凸凹分布与辐射热通量等几何内蕴量与力学量之间的关系。结果表明:复杂曲面表面高斯曲率的不连续分布将导致表面的变形能、摩擦耗损功出现相应的不连续分布;型面上沿拉伸方向截面线的法曲率越小,摩擦耗损功越大;型面上的热通量会随着拐点数量的增加而增加。这些结果为模具表面优化设计提供了新的理论依据。     

一种新的基于小波域的灰度水印嵌入算法

数字水印技术作为数字产品版权保护的一项新技术,已受到越来越多的关注.为保证水印的鲁棒性,利用人类的视觉特性,提出一种基于离散小波变换的数字水印技术,并给出了攻击分析.分析中,采用灰度图像作为数字水印,使其具有二维信号可视化的优点.实验表明,该算法能够经受住噪声、高斯滤波、压缩、直方图均衡化、增加对比度等的处理,具有较强的鲁棒性,是一种行之有效的水印嵌入方法.