共晶复合陶瓷损伤过程的有限元分析

针对共晶复合陶瓷的微观结构特征,建立了含强约束界面相的有限元模型,模拟了包含片状夹杂共晶复合陶瓷材料的外载应力场分布规律;应用ANSYS的APDL语言进行编程,对材料的损伤过程进行了研究。结果表明材料的破裂由基体损伤决定,随着外载荷的增加,损伤破坏沿界面延伸,并逐渐向基体内部扩展,最终造成基体的断裂。     

舰舰协同防空的舰空导弹杀伤区分析

针对舰艇编队协同防空时的耦合杀伤区形状及纵深等问题进行了研究,以定量地对编队耦合杀伤区进行简化描述。分析了单舰对典型目标的杀伤区特性,探讨了舰艇编队的典型防空队形,研究了纵向上递阶多层次、横向上同阶耦合的"递阶封闭圈原理"。以一阶耦合杀伤区为重点,依据攻击目标的不同,将其分成相对航路捷径为零和相对航路捷径均非零两类情况建立了耦合杀伤区纵深的计算模型,并扩展到了高阶耦合的情况。研究了耦合杀伤区与舰舰间距和来袭目标进攻舷角等参数的相互关系以及灵敏度。结果表明建立的模型符合实际,具有一定的指导意义。     

FLAMES仿真系统中目标毁伤仿真的实现

为了构建FLAMES中的目标毁伤仿真系统,在对FLAMES仿真系统体系结构分析的基础上,通过研究FLAMES中目标毁伤仿真的相关模型、函数及计算方法,归纳出目标毁伤仿真的实现流程。最后以飞机轰炸停机坪目标的毁伤计算为例,具体实现了FLAMES中的目标毁伤仿真。     

复杂目标毁伤效果评估的模糊专家系统框架研究

分析了复杂目标毁伤效果评估的特点和要求,提出能够满足毁伤效果评估要求的模糊专家系统方法。对模糊专家系统的基本结构、开发步骤进行了研究,建立了对复杂目标进行毁伤效果评估的模糊专家系统框架。以评估某电厂目标的毁伤效果为例,对模糊专家系统的建模步骤和关键技术进行了介绍。最后指出了模型的优缺点。     

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.     

A method to determine the shell layout scheme for equipment battlefield damage tests under artillery fire

In this paper,a new method for determining the shell layout scheme is proposed,which can make the equipment damage data by the battlefield damage test resemble as close as possible the actual combat data.This method is based on the analysis of the impact point distribution and effective damage area of equipment.In order to obtain the position of the impact points,an impact point distribution model under artillery fire was established.Similarly,in order to obtain the effective damage area of equipment,the concepts of generalized damage area and task-based equipment functional damage probability were demonstrated,and the corresponding calculation model was established.Through case analysis,the shell layout scheme was effectively obtained,verifying the correctness of the proposed method.     

防空目标分配中雷达遮蔽区问题研究

目标分配是防空指挥控制的主要任务,而目标相对于防空导弹火力单元的遮蔽判断是目标分配必须考虑的重要因素。分析了目标遮蔽区的判断条件,推导出目标在遮蔽区飞行时间的计算方法,提出了一种快速表示遮蔽区域图的离散处理方法,并研究了考虑目标遮蔽区影响的目标分配问题。通过实例计算,验证了目标遮蔽计算判断和分配方法的合理性,研究结果对实时指挥控制有应用价值。     

某型火箭炮弹对面积目标的毁伤仿真

某型火箭炮是新型的主战装备,对其战术技术性能的研究具有重要意义。采用仿真的方法对该型武器系统对目标的毁伤过程进行研究,可以大大节约实弹射击所需经费,并且可以动态地观察毁伤过程的细节。根据某型火箭炮弹抛撒子弹模型及子弹毁伤目标性能指标,采用理论分析和计算机模拟手段,对该型火箭炮弹对面积目标的毁伤过程进行了仿真,并得出了毁伤效率随子弹枚数和CEP的变化规律。研究成果对该型武器系统的作战运用具有借鉴意义。     

基于OPENGL的面目标平均相对毁伤计算方法

目前,均匀面目标平均相对毁伤的计算无论是解析法还是模拟法都采用了将面目标离散化的思想,存在着离散方法困难、计算精度差等特点.基于OpenGL像素颜色混合机制,提出了直接用像素点对面目标进行离散的方法,并结合Monte-Carlo模拟方法实现了对均匀面目标平均相对毁伤的计算,给出了算法的实现步骤,通过计算实例对计算结果进行了分析.实验结果表明,此方法是计算均匀面目标平均相对毁伤一种快速有效的方法.     

抗滑短桩与桩周土共同作用的探讨

根据某工程的应力监测结果和ANSYS计算结果,就抗滑短桩与桩周土共同作用进行探讨,得出了两点认识：第一,考虑桩土接触带贡献作用和桩-土共同工作是更趋于实际情况的,也是更经济合理的;考虑比不考虑桩土接触带的贡献,作用在抗滑短桩上的剩余水平下滑力约小10%。第二,接触带采用合适的弹性模量和厚度进行计算的结果与监测结果相当接近(相差≯5%)。