Experimental study on explosion dispersion process of a multi-layer composite charge under different initiation modes

The influence of initiation modes on the explosive dispersion process of the multi-layer composite charge (MCC) was studied. Overpressure sensors and high-speed photography system were used to investigate the energy release process of an MCC with a specific structure. The shock wave pressure and explosive dispersion characteristics of the MCC under different initiation modes were compared. The forming and expanding process of the shock wave of the composite charge under different initiation modes was determined. The separation position of the shock wave and fireball interface was determined. The calculation formulas of the shock radius and overpressure of the composite charge are presented. The radius of the shock wave of the composite charge was significantly affected by the initiation mode. Moreover, the development process of the composite explosive fireball under different initiation modes was analyzed, the variation rules of the composite charge dispersion radius and fireball dispersion velocity with time were obtained under the different initiation modes, the explosion energy release rate of composite charge under simultaneous initiation modes was the highest, and the peak overpressure under the simultaneous initiation mode was 1.61 times that of central single-point initiation.     

Investigation on energy output structure of explosives near-ground explosion

In order to give the energy output structure of typical explosives near-ground explosion in real ground conditions, the free-field shockwave, ground reflection shockwave and Mach wave overpressure time history of composition B explosive, RDX explosive and aluminized explosive were measured by air pressure sensors and ground pressure sensors. The shape of the free-field shock wave, ground reflection shock wave, and Mach wave and explosion flame were captured by high-speed camera. The experimental results show that, at the same horizontal distance from the initiation point, the peak overpressure of explosive shock wave of composition B explosive, both in the air and on the ground, is less than that of RDX and aluminized explosives. At a distance of 3.0 m from the initiation point, the peak overpressure of aluminized explosives is slightly less than that of RDX explosives. Owing to the exothermic effect of aluminum powder, the pressure drop of aluminized explosives is slower than that of RDX explosives. At 5.0 m from the initiation point, the peak overpressure of aluminized explosives is larger than that of RDX explosives. At the same position from the initiation point, among the three kinds of explosives, the impulse of aluminized explosives is the maximum and the impulse of composition B explosives is the minimum. With the increase of the horizontal distance from the initiation point, the height of Mach triple-points (Mach steam) of the three explosives increases gradually. At the same horizontal distance from the initiation point, there is poorly difference in the height of Mach triple-points between aluminized explosive and RDX explosive, and the height of Mach triple-points of composition B explosive is much smaller than that of other two explosives. The maximum diameter and duration of the fireball formed by aluminized explosives are the largest, followed by composition B explosive, and the maximum diameter and duration of the fireball formed by RDX explosive are the smallest.     

温度对半导体激光器退化的影响

采取等效电路模型仿真和加速退化试验相结合的方法研究温度对半导体激光器不同退化模式的影响规律。针对半导体激光器有源区退化和腔面退化进行分析,发现有源区退化会使半导体激光器阈值电流增大,而腔面退化会使半导体激光器斜率效率减小;进行了半导体激光器热特性建模与仿真,发现温度升高会使半导体激光器阈值电流增大;利用半导体激光器加速退化试验平台进行了半导体激光器加速退化试验。仿真与试验结果证明:温度升高会加剧半导体激光器腔面退化,而对有源区退化无显著影响。上述结论对进一步完善半导体激光器温度-退化仿真模型,研究温度对半导体激光器退化的作用机理和防护措施有积极作用。     

斜入射条件下F-P干涉腔透过率特性分析

分析了斜入射角条件下F-P干涉腔的透过率特性;结合单层介质膜和单层金属膜的反射特性随入射角的变化规律,得出了反射特性参数为恒定值时微腔、低反F-P干涉腔透过率的计算误差;仿真结果表明,在光束斜入射条件下,特别是在大入射角下,单层介质膜的反射率指数增大,单层金属膜的反射率和反射相移也指数增大,但其吸收系数指数减小,造成微腔、低反F-P干涉腔透过率曲线与反射特性参数为恒定值时相比均明显向下偏移,且偏移量逐渐增大。     

Ka波段VCO控制信号发生器设计及调制域测试方法

采用DSP的SPORT端口控制16位高速串行DAC,设计了任意电压信号发生器,用于控制Ka波段连续波雷达压控振荡器产生频率可任意调制的发射信号。利用该信号发生器与调制域分析仪,测试了压控振荡器的调制特性和阶跃响应。     

基于门限的无线传感器网络密钥管理方案

由于无线传感器网络在能量消耗、内存开销和计算能力等方面的局限性,传统的网络密钥管理方法已不适用。为此提出了一种适用于无线传感器网络的密钥预分配方法——基于（t,n）-门限方案,给出了密钥分配方法,并从方案的连通性、安全性等方面进行了有效的分析,结果表明该算法在这些方面有一定的优势。     

基于相关算法超声流量计的研究

为解决开采原油的精确在线计量问题,在对超声波相关流量计原理分析的基础上,重点研究了超声波相关流量算法。采用循环相关算法,有效克服了有限长离散数据线性相关算法所出现的计算失效问题,并以DSP芯片为核心,实现了超声波相关流量测量系统的设计,完成了信息不丢失测量以及对困难流体流量的非接触在线计量。实验方案经油田现场测试,计量误差可以控制在2%以内。     

断裂复合材料层压板贴片快速修复工艺研究

采用CMR-1A复合材料热补仪和3234/G814复合材料预浸料贴片,对完全断裂的复合材料层压板进行双面修复。通过正交试验法获得了最佳修复工艺参数:固化温度为130℃;固化时间为80 min;贴片层数为5层(单面);真空度为0.04 MPa;贴片长度为50 mm。对优化工艺参数进行试验验证,结果表明:复合材料层压板拉伸强度从0 MPa增加到320.84 MPa,提高了57.29%;LY12CZ铝合金和45钢板拉伸强度恢复率分别为96%和75.53%。     

考虑细观结构变化的原状Q3黄土变形和强度特性

为研究结构性对非饱和原状Q3黄土变形和强度特性的影响,做了12个非饱和原状Q3黄土的CT-三轴侧向卸荷试验。在试验剪切过程中,利用CT机对试样进行跟踪扫描,共得到168张CT图像。基于试验数据建立了细观结构参数,并利用该参数来反映非饱和原状Q3黄土的变形和强度特性,从而得到能反映细观结构性影响的非线性应力-应变关系以及摩尔-库伦强度公式。     

目标运动要素误差对尾流自导鱼雷自导开机距离的影响

尾流自导鱼雷自导开机距离设置直接影响到鱼雷是否能可靠捕获尾流,开机距离的设置通常考虑尾流自导装置自适应调整及目标运动要素误差的影响,射击态势的影响因素不容忽视但未引起足够重视。通过分析计算不同射击态势下目标运动要素误差对尾流自导鱼雷直航段航程的影响,得出了射击态势对尾流自导鱼雷自导装置开机距离影响的程度及规律。