多方位测量的相位双差GNSS欺骗干扰检测算法

对于二元天线阵,相位双差检测算法的载波相位双差角度模糊、虚警概率较高,这限制了算法的应用。针对这一问题,提出天线阵方位变化的欺骗干扰检测算法。通过二元天线阵在不同方位估计信号的载波相位双差,进行多次判决,有效消除角度模糊,降低检测的虚警概率,实现二元天线的载波相位双差检测。建立仿真模型,并通过仿真计算分析验证了该方法的有效性。     

单洞双层隧道围岩力学特性分析

单洞双层隧道作为一种新的隧道形式,不同于分离式隧道和连拱式隧道。利用ANSYS对单洞双层隧道和分离式隧道开挖后围岩的情况进行数值模拟,分析开挖后围岩的应力和位移变化情况、塑性区分布和安全系数,通过对比得出：在浅埋情况下两种隧道围岩应力和位移分布基本一致,地表沉降和分离式隧道相当;单洞双层隧道对围岩扰动深度较大,边墙是其薄弱部位,应力松弛明显,水平位移较大,塑性区水平方向分布较大。     

双重改性空心微珠的制备及表征

首先采用液相沉积碳化法对空心微珠表面进行无机改性,制备出表面无机改性空心微珠;再对无机改性空心微珠进行有机改性,制备出了双重改性空心微珠。采用扫描电子显微镜、X射线衍射、红外光谱、热失重以及分光光度计法对双重改性空心微珠的制备进行了表征。结果表明：采用双重改性方法制备的表面改性空心微珠微观形貌仍为球状,微珠由灰黑色变为淡黄色;微珠表面的CaCO3属方解石相六方晶系;双重改性空心微珠中CaCO3质量分数约为7%,有机改性剂质量分数约为17%。双重改性空心微珠较之单纯有机改性空心微珠在500SN基础油中的分散稳定性能明显提高。     

双层柱壳的流固耦合模态计算与试验研究

采用结构有限元和内域流体有限元的流固耦合计算方法,对球壳及其内域流体进行有限元离散计算,并将计算所得的模态振动频率与理论结果进行了比较.采用同样的方法,进一步对加筋双层圆柱壳进行了流固耦合的复特征值分析,并求解了其固有频率和振型.试验分别对双层柱壳充水和不充水情况下模态和模态频率进行了测量,结果证实了数值计算方法的正确性.     

The incentive effect of acceptance sampling plans in a supply chain with endogenous product quality

This article studies a firm that procures a product from a supplier. The quality of each product unit is measured by a continuous variable that follows a normal distribution and is correlated within a batch. The firm conducts an inspection and pays the supplier only if the product batch passes the inspection. The inspection not only serves the purpose of preventing a bad batch from reaching customers but also offers the supplier an incentive to improve product quality. The firm determines the acceptance sampling plan, and the supplier determines the quality effort level in either a simultaneous game or a Stackelberg leadership game, in which both parties share inspection cost and recall loss caused by low product quality. In the simultaneous game, we identify the Nash equilibrium form, provide sufficient conditions that guarantee the existence of a pure strategy Nash equilibrium, and find parameter settings under which the decentralized and centralized supply chains achieve the same outcome. By numerical experiments, we show that the firm's acceptance sampling plan and the supplier's quality effort level are sensitive to both the recall loss sharing ratio and the game format (i.e., the precommitment assumption of the inspection policy). © 2013 Wiley Periodicals, Inc. Naval Research Logistics, 2013     

Multidirectional scheduling scheme in resource‐constrained project schedulingproblem

In 2000, Klein showed that bidirectional scheduling schemes (bidss) outperform single‐directional scheduling schemes (e.g., forward or backward schemes). In 2010, Yoosefzadeh, et al. [J Math Model Algor 9 (2010), 357–373] showed that depending on the nature of the problems and also the type of priority rules used, schedules produced by a so‐called tridirectional scheduling scheme (trdss) yields shorter makespans when compared to forward, backward, and even bidss. Since the justification technique is applied in many of the state‐of‐the‐art algorithms nowadays, we show that the tuned version of the trdss outperforms the double justification technique. Moreover, we investigate the circumstances under which the trdss is more probable to generate schedules with shorter makespans. To this end, we introduce a new measure of resource requirements and their distributions, namely total amount of overflows. Our analytical as well as empirical investigations show that when the new measure is increased, it is more probable to obtain schedules with shorter makespans using the trdss. © 2013 Wiley Periodicals, Inc. Naval Research Logistics 61: 44–55, 2014     

Simulation of the plasticizing behavior of composite modified double-base (CMDB) propellant in grooved calendar based on adaptive grid technology

The frequent occurrence of safety accidents during the calendering process is caused by the flammable and explosive properties of composite modified double-base (CMDB) propellant. Optimization of process parameters with the aid of fluid simulation technology could effectively ensure the safety of the calendering process. To improve the accuracy of the simulation results, material parameters and model structure were corrected based on actual conditions, and adaptive grid technology was applied in the local mesh refinement. In addition, the rheological behavior, motion trajectories and heat transfer mechanisms of CMDB propellant slurry were studied with different gaps, rotational rates and temperatures of two rollers. The results indicated that the refined mesh could significantly improve the contour clarity of boundaries and simulate the characteristics of CMDB propellant slurry reflux movement caused by the convergent flow near the outlet. Compared with the gap, the increased rotational rate of roller could promote the reflux movement and intensify the shear flow of slurry inside the flow region by viscous shear dragging. Meanwhile, under the synergistic effect of contact heat transfer as well as convective heat exchange, heat accumulated near the outlet and diffused along the reflux movement, which led to the countercurrent heat dissipation behavior of CMDB propellant slurry. The plasticizing mechanism of slurry and the safety of calendering under different conditions were explored, which provided theoretical guidance and reference data for the optimization of calendering process conditions. Based on the simulation results, the safety of the CMDB propellant calendering process could be significantly improved with a few tests conducted during a short research and development cycle.     

采用副载波参考波形方法的GNSS双载波环多径抑制技术

为了实现对高阶二进制偏移载波(BOC)信号的无模糊和抗多径接收,将码相关参考波形的闸波设计思路应用于GNSS双载波环路接收方法的副载波锁相环。在副载波锁相环中引入设计的闸波参与信号的相干积分过程,使双载波环法具备抗多径性能且不需要额外引入相关器。对该设计方法的理论和具体实现进行阐述和分析,从副载波多径误差包络和跟踪精度两方面对改进的双载波环路方法性能进行评估。仿真结果显示,采用的算法与双载波环路法相比,可以降低BOC(1,1)信号81.1%的副载波多径误差包络面积以及BOC(14,2)信号75.1%的副载波多径误差包络面积。但是,改进的双载波环路法会带来-6 dB的相干积分后载噪比损失,降低跟踪精度。因此,在闸波参数设计上,需要谨慎选择以平衡算法的多径抑制和跟踪精度性能。综合来看,该方法适用于解决非弱信号条件下及多径环境下的高阶BOC信号接收问题。     

多舰对抗研究

研究了海上军事实战模式抽象出的一追二和一二对抗的两大问题。解决一追二问题的方法共讨论了三种：初始角的平分线航向法、瞬时角的平分线航向法、中点轨迹法。给出了确定性的数学模型、以及选代计算方法。一二对抗问题的结论可以由—一对抗问题的结论经过迭加而得到。而—一对抗问题的解决是以定性微分对策的双边极值原理为基础展开的。     

一种双参数批更换系统的优化问题

研究了一种在更换时间有限的情况下 ,基于交替更新过程的双参数批更换系统的优化问题 ,这一问题的目标是平均费用率的极小化。给出了一种特殊情况的讨论结果。