短波跳频电台组网研究

短波跳频电台组网在军事通信中占有重要地位,组网应用可以提高跳频电台的抗干扰性能.介绍了跳频通信的特点及抗干扰性能,分析了短波跳频通信技术的发展趋势.短波跳频电台组网可以提高通信的可通概率与战术应用的灵活性,为此着重研究了短波跳频电台组网的原理与方法以及组网的注意事项,为军事短波跳频电台的组网应用奠定基础.     

A stochastic model for burn‐in procedures in accelerated environment

Burn‐in procedure is a manufacturing technique that is intended to eliminate early failures of system or product. Burning‐in a component or system means to subject it to a period of use prior to being used in field. Generally, burn‐in is considered expensive and so the length of burn‐in is typically limited. Thus, burn‐in is most often accomplished in an accelerated environment in order to shorten the burn‐in process. A new failure rate model for an accelerated burn‐in procedure, which incorporates the accelerated ageing process induced by the accelerated environmental stress, is proposed. Under a more general assumption on the shape of failure rate function of products, which includes the traditional bathtub‐shaped failure rate function as a special case, upper bounds for optimal burn‐in time will be derived. A numerical example will also be given for illustration. © 2006 Wiley Periodicals, Inc. Naval Research Logistics, 2006     

基于退化速率跟踪粒子滤波的剩余使用寿命预测框架

毋庸置疑,剩余使用寿命预测对于设备的健康管理越来越重要。近年来粒子滤波方法被越来越多地应用到设备寿命预测技术当中,这是因为粒子滤波方法能更好的解决非线性非高斯系统滤波问题,而且能够获得不确定度信息。但该方法的预测性能却过度依赖于预测模型,并且对于模型参数的初始分布也比较敏感,这在一定程度上限制了粒子滤波预测方法的进一步发展。本文针对基本粒子滤波预测方法的不足,提出了一种基于退化速率跟踪粒子滤波的通用预测框架,以历史观测数据的退化速率统计规律作为指导来跟踪目标数据的退化速率,实现对粒子滤波预测方法的简化。并将该方法用于轴承和锂离子电池的剩余使用寿命预测,验证了方法的有效性。     

基于自适应阈值的FAST特征点提取算法

FAST特征提取算法阈值选取固定,因此不能满足不同图像的特征点抽取要求,并且提取的结果存在着多个特征点块的现象。针对这些缺陷,首先采用动态全局阈值对原始灰度图像进行初步提取得到候选特征点,然后采取动态局部阈值和非极大值抑制法进一步对候选特征点进行筛选,从而达到自适应选取阈值和抑制多个特征点块的目的。实验表明,改进后的算法稳定性高,对不同光照和对比度情况下有一定的适应能力,并且运算量相对比于其他一些特征提取算法要小得多,满足实时应用的要求。     

基于北斗、短波的高精度时钟系统研究与设计

介绍了北斗、短波授时技术;对高稳恒温晶振及其频率特性进行分析的基础上,设计了一种基于北斗卫星、短波无线电授时的高精度时钟系统;该系统通过利用北斗接收处理模块、短波授时接收模块得到的秒脉冲信号、时间信息,经过延迟修正处理、脉冲滤波、脉冲补偿、脉冲统计得到标准的秒脉冲信号,实现对恒温晶振频率的校准,获得一个短期及长期频率稳定度都比较优良的时间频率标准,同时利用校频后恒温晶振分频出的1pps信号对时间芯片进行校准,对外输出高精度时间信息;对恒温晶振校频系统的基本工作原理及部分模块电路图进行了说明,试验结果表明,在时间不长于1h内,频率准确度优于1×10-10;该系统实用方便的方法达到了将晶体振荡器校准到较高指标的目的。     

Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Formation of adiabatic shearing band for high-strength Ti-5553 alloy: A dramatic thermoplastic microstructural evolution

By using split Hopkinson pressure bar, optical microscopy and electronic microscopy, we investigate the influence of initial microstructures on the adiabatic shear behavior of high-strength Ti–5Al–5V–5Mo–3Cr (Ti-5553) alloy with lamellar microstructure and bimodal microstructure. Lamellar alloy tends to form adiabatic shearing band (ASB) at low compression strain, while bimodal alloy is considerably ASB-resistant. Comparing with the initial microstructure of Ti-5553 alloy, we find that the microstructure of the ASB changes dramatically. Adiabatic shear of lamellar Ti-5553 alloy not only results in the formation of recrystallized β nano-grains within the ASB, but also leads to the chemical redistribution of the alloying elements such as Al, V, Cr and Mo. As a result, the alloying elements distribute evenly in the ASB. In contrast, the dramatic adiabatic shear of bimodal alloy might give rise to the complete lamination of the globular primary α grain and the equiaxial prior β grain, which is accompanied by the dynamic recrystallization of α lamellae and β lamellae. As a result, ASB of bimodal alloy is composed of α/β nano-multilayers. Chemical redistribution does not occur in ASB of bimodal alloy. Bimodal Ti-5553 alloy should be a promising candidate for high performance armors with high mass efficiency due to the processes high dynamic flow stress and excellent ASB-resistance.     

基于影响图方法的信息战模型

由于粒子滤波的算法原理,其计算量很大。研究了针对机动目标的交互式多模型粒子滤波器(IMMPF)算法和多速率交互式多模型(MRIMM)算法,提出了多速率交互式多模型粒子滤波器(MRIMMPF)算法。该算法是在交互式多模型粒子滤波器(IMMPF)的基础上引入多速率技术,期望在保持IMMPF的性能同时能够减少因为粒子滤波带来的计算量;最后通过和一般基于EKF的IMM算法、IMMPF算法的比较,验证了该算法的有效性。     

A general model of heterogeneous system lifetimes and conditions for system burn‐in

Burn‐in is a technique to enhance reliability by eliminating weak items from a population of items having heterogeneous lifetimes. System burn‐in can improve system reliability, but the conditions for system burn‐in to be performed after component burn‐in remain a little understood mathematical challenge. To derive such conditions, we first introduce a general model of heterogeneous system lifetimes, in which the component burn‐in information and assembly problems are related to the prediction of system burn‐in. Many existing system burn‐in models become special cases and two important results are identified. First, heterogeneous system lifetimes can be understood naturally as a consequence of heterogeneous component lifetimes and heterogeneous assembly quality. Second, system burn‐in is effective if assembly quality variation in the components and connections which are arranged in series is greater than a threshold, where the threshold depends on the system structure and component failure rates. © 2003 Wiley Periodicals, Inc. Naval Research Logistics 50: 364–380, 2003.     

一种基于条件概率的设备占用率修正算法

简要介绍了某型无人机维修级别分析中的组合方案法 ,针对传统分析法中设备占用率采用经验值 ,造成可信度低的问题 ,提出了一种基于不同故障模式发生时的条件概率求解设备占用率的算法 ,并给出了这种算法的适用范围。