基于PON技术的多站雷达数字光纤传输系统设计

提出一种多站雷达体系雷达数据光纤传输系统的方案设计和实现方法。与传统雷达使用的光纤传输系统不同,而是采用技术较新的基于无源光网络PON的实时数据通信系统,这是无源光网络技术在多传感器实时通信领域的首次应用。在系统设计中利用先进的光电子和在编程技术,实现了点对多点雷达数据光纤传输,提高了信号传输质量,同时系统具有动态接入和扩容的能力。     

钢丝绳联轴器的性能试验及数学模型

对钢丝绳联轴器进行了动刚度性能实验 ,在此基础上建立了数学模型 ,并进行了参数辨识 ,指出钢丝绳联轴器具有强非线性 ,对减小轴系扭转振动具有良好的效果     

潜艇耐压壳动力学响应和声辐射研究概况与趋势

论述了流场中潜艇耐压壳自由振动、受简谐力或力矩作用和受冲击载荷情况下的动力学响应和声辐射研究概况 ,讨论了带有阻尼材料的复合潜艇耐压壳的动力学和声辐射研究情况 ,以及阻尼材料的破坏研究概况 ,并指出了今后的研究方向     

基于案例推理和模糊诊断的兵器故障诊断专家系统

讨论了基于案例的推理和模糊诊断矩阵在兵器故障中的应用 ,建立了兵器故障诊断WDDS -E系统模型和模糊诊断矩阵模型。详细说明了系统的工作原理和设计过程 ,并给出了应用实例     

军校开展案例教学之我见

案例教学作为一种行之有效的教学方法,有助于锻炼和提高军队院校学员分析问题、解决问题的能力,军校应正确认识案例教学的重要意义,深入探讨如何选编案例以及实施案例教学的具体措施。     

Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

甲板坐标系下速率火控射击诸元解算及弹道修正

速率火控系统是在甲板坐标系下解相遇的,它不依赖于导航系统.它与常规火控不同,甲板倾斜的修正不能采用简单的坐标系变换的方式.针对速率火控甲板倾斜修正问题,指出了两种需要进行甲板倾斜修正的情况,推导给出了计算方法,通过原理仿真计算,验证了计算方法的正确性.     

线导鱼雷导引弹道的动力学分析

通过线导鱼雷常用导引方法—三点法、前置角法导引弹道的动力学分析 ,推导出不同方法下鱼雷旋回速率的解析表达式 ,并通过数字仿真对鱼雷线导导引弹道动力学特性进行探讨 ,明确了线导鱼雷导引弹道特性与导引方法之间的关系 .     

Optimal (τ, T) opportunistic maintenance of a k‐out‐of‐n:G system with imperfect PM and partial failure

The opportunistic maintenance of a k‐out‐of‐n:G system with imperfect preventive maintenance (PM) is studied in this paper, where partial failure is allowed. In many applications, the optimal maintenance actions for one component often depend on the states of the other components and system reliability requirements. Two new (τ, T) opportunistic maintenance models with the consideration of reliability requirements are proposed. In these two models, only minimal repairs are performed on failed components before time τ and the corrective maintenance (CM) of all failed components are combined with PM of all functioning but deteriorated components after τ; if the system survives to time T without perfect maintenance, it will be subject to PM at time T. Considering maintenance time, asymptotic system cost rate and availability are derived. The results obtained generalize and unify some previous research in this area. Application to aircraft engine maintenance is presented. © 2000 John Wiley & Sons;, Inc. Naval Research Logistics 47: 223–239, 2000     

如何估计软件的MTBF

软件剩余初始故障个数No、平均无故障时间MTBF、故障暴露率λ和软件运行的成功率θ等是衡量软件可靠性的重要参数.其中对高可靠性软件(包括军用软件等)MTBF是最重要的.传统的MTBF计算方法有2种一是计算发生故障的平均时间间隔二是通过软件可靠性模型进行估计.前者代价较大,后者不太准确.本文从软件的失败率入手研究软件的MTBF,这是一个比较贴近实际的方法.