5GHz雷达的干扰计算模型概述

文章从开发5 GHz模型的目的入手,简要介绍了5 GHz模型的结构组成,详细讨论了5 GHz模型的干扰计算流程,包括无线局域网和雷达的场景设置、技术参数设置、总干扰计算等,最后给出了5 GHz模型的一个运行范例,以期为其它干扰模型的开发提供借鉴参考。     

基于红蓝对抗的实战化教学组训方法研究 —— 以航空兵初级指挥专业为例

红蓝对抗训练是实战化训练的最高形式,近年来在部队演习演练中被广泛采用,效果显著。军队院校教学向部队靠拢,向实战聚焦,可在航空兵初级指挥专业的人才培养中引入红蓝属性,开展实战化教学的探索和实践。本文提出“模拟环境+师生对抗+硬度可调”的实战化教学组训方法：一是红蓝对抗模拟训练环境,可支撑航空兵初级指挥专业学员开展“规划-部署-实施-评估”的航空兵作战全流程红蓝对抗实战化教学;二是“蓝”教员和“红”学员师生对抗教学组织实施程序;三是适应学员能力渐进式增长的关于训练想定、蓝军能力、导调方式和评定标准的“硬度可调”机制。此外,为确保红蓝对抗实战化教学的顺利实施,给出了锻造“红蓝兼备”院校“蓝”教员队伍的几点建议。     

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.     

Thermodynamics and performance of Al/CuO nanothermite with different storage time

The storage stability of energetic materials is important for its application. Here, the storage stability of Al/CuO nanothermite, which was prepared by electrospray method and stored with different storage time, was systematically researched. The activation energy of Al/CuO nanothermite was calculated by differential scanning calorimetry (DSC). The ignition temperature and the curve pressure history of Al/CuO nanothermite was measured using ignition temperature measuring device and constant-volume pressurization tests, respectively. Further, the thermites were characterized by X-ray Diffractometer (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM) and Transmission electron microscopy (TEM). The results show that the morphology of the thermites did not change significantly. The activation energy was decreased from 254.1 kJ/mol to 181.8 kJ/mol after storage for 13 months. When stored for 0, 7 and 13 months, the peak pressures of Al/CuO nanothermite were 685.8 kPa, 626.3 kPa and 625.5 kPa, respectively. In addition to the ignition temperature, it was 775 ℃, 739 ℃ and 754 ℃, respectively. This result indicated that the ignition and combustion properties of Al/CuO nano-thermite are obviously reduced when stored for a long time, at room temperature.     

阻尼振荡的数学本质分析

用微分方程定性理论,从平面自治系统奇点的性态角度出发分析了阻尼振荡的数学本质。以全新的视角讨论了三种阻尼情况的本质区别,由此引出了系统在平衡态的稳定性问题。进一步用系统稳定性理论论述了自激振荡器的设计思想。该分析方法也是研究非线性动态电路、动力系统稳定性的有效方法。     

发动机动态特性及其对车辆换档特性的影响

分析了影响发动机动态特性的因素,并通过试验得出了动态特性与稳态特性的关系。根据试验结果,分析了动态特性对车辆换档特性的影响,得出按发动机动态特性设计换档规律,有利于车辆换档特性的改善。     

GPS弹道修正引信弹道环境信息的解算与数值仿真分析

根据质点弹道的特点, 描述了弹目间距、弹炮间距和相对弹道高 3个弹道环境信息的概念, 然后应用数学方法对弹目间距、弹炮间距和相对弹道高进行了理论计算推导, 建立了数学解算模型, 并用MATLAB程序进行了数值仿真计算, 通过分析其数值变化的规律和特点提出了其应用方向。     

IEC标准与ESD抗扰度实验方法研究

对ESD抗扰度实验方法和 2种ESD模拟器进行了系统的研究, 发现IEC61000-4-2标准规定的静电放电抗扰度实验方法和实验用的ESD模拟器存在严重的问题。针对这些问题并结合当前国外学者研究的有关结论,研制了一种更符合实际需要的ESD抗扰度检测试验方法和实验装置。利用新研制的实验平台对瑞士Schaffner公司制造的NSG435ESD模拟器和日本Noiseken公司制造的ESS-200AXESD模拟器进行了比较研究, 对模拟器内部高压继电器动作产生的辐射场造成实验结果偏差问题进行了测试分析。利用该实验装置分别以手动控制模拟器和自动控制装置控制模拟器完成了空气放电过程。对空气放电电流波形的重复性进行了研究, 证明利用这种平台可以有效地控制空气放电的重复性。     

大口径机枪结构动力学建模方法研究

总结了我国近年来关于大口径机枪结构动力学建模方法研究的主要成果,分析了目前建模方法上存在的某些问题以及对武器装备研制的影响,进一步介绍了边界条件的确定、模型正确性判别和载荷识别等方面的新技术。     

高边坡挡墙变形监测方法探讨——全站仪自由设站差分法

常用的高边坡监测方法是在高边坡周围设立固定的观测基站对高边坡进行监测,但高边坡变形会使观测基点产生位移,从而影响观测数据的准确性.为了避免高边坡变形对设立的固定观测基点的影响,提高观测精度,提出了全站仪自由设站坐标差分法的观测方法,论述了该方法的原理、误差分析以及其在高边坡变形监测中的应用.对在特殊环境下的变形观测有一定的指导意义.