基于电测法的导引头伺服机构干扰力矩测量及精密装配工艺优化

为了在导引头伺服机构装配过程中减小干扰力矩,基于电测法搭建伺服机构驱动力矩测量系统,采用Labview和Dliphi开发了测量系统上下位软件;在精密装调过程中,通过实时监测驱动力矩,调整装调参数,达到减小干扰力矩的作用。对质量不平衡力矩及活动线缆力矩在驱动力矩中的特性进行了实验验证,确定伺服机构配平和布线方法;对轴承预紧力与伺服机构摩擦力矩关系进行了实验验证,解决自动跑合工艺问题,对减小摩擦力矩波动幅值具有重要意义;测量伺服机构转轴回转误,明确最佳轴承预紧力的工艺方法。基于搭建的驱动力矩测量系统对传统的伺服机构装配工艺进行优化,将依赖技师经验装配的定性方法优化为依赖力矩测量的定性方法。     

环境温度变化对导引头伺服机构摩擦力矩影响分析及实验研究

建立包含框架热致耦合变形的导引头伺服机构摩擦力矩分析模型,重点研究环境温度变化对角接触轴承几何参数及摩擦力矩的影响。以反射镜式导引头为例进行摩擦力矩分析,结果表明:随着温度的降低,润滑脂黏度的上升是导致伺服机构在低温时摩擦力矩剧烈上升的主要原因,框架耦合变形占比较小。搭建基于电测法的摩擦力矩测试系统,用快速温变实验箱模拟环境温度,测量伺服机构摩擦力矩并与理论计算结果进行对比分析,实验证明摩擦力矩实验结果与理论模型计算结果一致。     

含运动副间隙舵机执行机构的动态特性研究

为了研究运动副间隙对空间4R机构动态特性的影响,间隙处的接触碰撞模型和摩擦的建立分别采用非线性弹簧阻尼模型和修正的库伦摩擦模型。在Solidworks中建立空间4R机构模型,导入ADAMS中进行动力学仿真分析。对比含间隙和不含间隙时系统动力学仿真结果的异同,分析间隙大小和最佳间隙量对空间4R机构动态特性的影响,为机构的设计提供了重要的参考依据,有利于工程实际应用。     

基于SWOT分析的军队审计容错免责机制完善路径研究

军队审计容错免责机制是在审计权限范围内对符合容错免责情形的事由减轻或免于问责并及时纠正的稳定工作机制,是审计问责态势下应对“为官不为”问题的合理路径。本文基于SWOT法分析认为,当前审计环境下建立军队审计容错免责机制的优势在于独立的经济监督地位、专业的经济监督力量和广泛的经济监督对象,劣势在于单一的认定主体、缺失的法律规范和匮乏的免责素质,机遇在于利好政策的出台、国家审计的实践经验和军队审计的职能定位,威胁在于制度规范笼统、审计风险扩大和资源矛盾加剧。在此基础上,本研究基于W-T（劣势-威胁）的战略选择,提出完善军队审计容错免责机制的现实路径,即：明确机制定位,科学界定边界;完善制度规范,形成法律依据;完备容错清单,转变审计模式;优化容错环境,降低容错风险。     

Effect of change of sand properties on travel distance of ricocheted debris

The debris from exploded buildings can ricochet after colliding with the ground, thus increasing the debris travel distance and danger from any associated impacts or collisions. To reduce this danger, the travel distance of ricocheted debris must be accurately predicted. This study analyzed the change in the travel distance of ricocheted concrete debris relative to changes in the properties of a sand medium. Direct shear tests were conducted to measure the change in internal friction angle as a function of temperature and water content of the sand. Finite element analysis (FEA) was then applied to these variables to predict the speed and angle of the debris after ricochet. The FEA results were compared with results of low-speed ricochet experiments, which employed variable temperature and water content. The travel distance of the debris was calculated using MATLAB, via trajectory equations considering the drag coefficient. As the internal friction angle decreased, the shear stress decreased, leading to deeper penetration of the debris into the sand. As the loss of kinetic energy increased, the velocity and travel distance of the ricocheted debris decreased. Changes in the ricochet velocity and travel distance of the debris, according to changes in the internal friction angle, indicated that the debris was affected by the environment.     

Fracture mechanism of a cylindrical shell cut by circumferential detonation collision

The failure mechanism of a cylindrical shell cut into fragments by circumferential detonation collision was experimentally and numerically investigated. A self-designed detonation wave regulator was used to control the detonation and cut the shell. It was found that the self-designed regulator controlled the fragment shape. The macrostructure and micro-characteristics of fragments revealed that shear fracture was a prior mechanism, the shell fractured not only at the position of detonation collision, but the crack also penetrated the shell at the first contact position of the Chapmen-Jouguet (C-J) wave. The effects of groove number and outer layer thickness on the fracture behavior were tested by simulations. When the thickness of the outer layer was 5–18 mm, it has little effect on fragmentation of the shell, and shells all fractured at similar positions. The increase of the groove number reduced the fracture possibility of the first contact position of the C-J wave. When the groove number reached 7 with a 10 mm outer layer (1/4 model), the fracture only occurred at the position of detonation collision and the fragment width rebounded.     

Hypersonic impact flash characteristics of a long-rod projectile collision with a thin plate target

Impact flash occurs when objects collide at supersonic speeds and can be used for real-time damage assessment when weapons rely on kinetic energy to destroy targets.However,the mechanism of impact flash remains unclear.A series of impact flash experiments of flat-head long-rod projectiles impacting thin target plates were performed with a two-stage light gas gun.The impact flash spectra for 6061 aluminum at 1.3-3.2 km/s collision speeds were recorded with a high-speed camera,a photoelectric sensor,and a time-resolved spectrometer.The intensity of the impact flash exhibited a pulse charac-teristic with time.The intensity(I)increased with impact velocity(V0)according to I∝Vn0,where n = 4.41 for V0 ＞ 2 km/s.However,for V0 ＜ 2 km/s,n = 2.21,and the intense flash duration is an order of magnitude less than that of higher V0.When V0 ＞ 2 km/s,a continuous spectrum(thermal radiation background)was observed and increased in intensity with V0.However,for V0 ＜ 2 km/s,only atomic line spectra were detected.There was no aluminum spectral lines for V0 ＜ 2 km/s,which indicated that it had not been vaporized.The initial intense flash was emission from excited and ionized ambient gases near the impact surface,and had little relationship with shock temperature rise,indicating a new mechanism of impact flash.     

基于油液分析的自行火炮装备性能监测研究

提出了一种基于油液光谱分析技术的自行火炮装备磨损故障诊断方法 ,该方法主要包括用于监测润滑油中磨损金属颗粒浓度变化的模型 ,并制定了各主要磨损金属元素的浓度和梯度界限值 ,并将其分为三个层次。同时将灰色建模理论引入光谱分析领域 ,通过拟合光谱仪分析的数据 ,掌握润滑油中磨损金属颗粒浓度的变化规律 ,进而对其浓度变化规律进行预测 ,从而达到对装备进行性能监测的目的。     

消防部队化学事故应急救援预案的制定与演习

阐述公安消防部队制定化学事故应急救援预案的程序、方法、步骤及制定预案时应考虑的各种因素;并对化学事故应急预案在不同条件下实施演习的程序、方法及演习过程中应注意的问题提出看法.     

外槽轮机构分度精度分析与设计

分析了外槽轮机构主要零部件的设计精度对槽轮分度精度的影响 ,结果表明主动件长度和滚子与轮槽之间的间隙对分度精度影响最大。用概率与数理统计的方法导出了精度设计公式并给出一个计算实例