潮流与风对单点系泊系统运动稳定性的影响研究

应用时域仿真的方法研究了风与潮流作用下单点系泊系统的非线性动力学特性。以三阶操纵运动方程为基础,引入定常的风力、潮流作用力和二阶波浪力,建立了系泊系统三自由度运动微分方程,据此建立了系泊系统的多自由度计算机仿真模型。风与潮流联合作用的情形下,对一艘单点系泊油轮的动力学行为进行了数值仿真研究。以潮流速度和系缆长度为分岔控制参数,在参数平面上给出了油轮系泊运动的Hopf分岔集,它将参数平面分为两个系统动力学行为本质不同的区域。研究表明,与潮流(顶流)单独作用的情形相比,顶风条件增加了油轮静止系泊位置的Liapunov稳定性。     

点型火灾报警探测器保护范围对布置的影响

分析了点型火灾报警探测器＂保护半径＂与＂保护面积＂的内在关系,得出了以保护半径为主,保护面积及修正系数为辅新型计算方法,使其在不规则平面更有可操作性,能充分发挥探测器效能,给设置留下了宽裕的选择范围,使设置更趋合理;在安全性不受影响下,探测器用量最大可节省12%。     

论唯物史观的价值内涵

马克思的唯物史观作为一种理解与把握社会历史本质、社会历史现象的根本方法,既包含着对社会历史发展的客观必然性的理解,具有科学性的特征,也包含着人类社会自身的价值取向,贯穿着一定的价值理想与价值追求。     

CCRP(炸弹)对地攻击原理算法研究

本文在引入“计算航向”这一概念的基础上重新列出了CCRP对地攻击原理的计算公式。并由此计算出描述投放点相对本机位置的⊿K 与⊿t 两个量。⊿K 表示在当前的攻击条件下“计算航向”与实际航向之差,“计算航向”表示本机若在当前沿该航向按给定条件飞行,则经一定时间⊿t 后即可到达正确的投弹点。     

Effects of nano-sized aluminum on detonation characteristics and metal acceleration for RDX-based aluminized explosive

Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the param-eters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0％to 15％,every 5％increase of aluminum resulted in about a 1.3％decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14％and 8％higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 μs throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12％and 2.9 μs higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80％of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.     

A method to determine the shell layout scheme for equipment battlefield damage tests under artillery fire

In this paper,a new method for determining the shell layout scheme is proposed,which can make the equipment damage data by the battlefield damage test resemble as close as possible the actual combat data.This method is based on the analysis of the impact point distribution and effective damage area of equipment.In order to obtain the position of the impact points,an impact point distribution model under artillery fire was established.Similarly,in order to obtain the effective damage area of equipment,the concepts of generalized damage area and task-based equipment functional damage probability were demonstrated,and the corresponding calculation model was established.Through case analysis,the shell layout scheme was effectively obtained,verifying the correctness of the proposed method.     

Essentially Non-Oscillatory插值的分析与方法

在科学研究与工程计算中对插值的分析与方法理论已有很重要的应用,而对于ENO插值的方法与理论在大多教科书中却很少涉及,本文介绍ENO插值的应用及算法,为大学生们学习数值分析中的插值计算提供参考。     

一类m-点边值问题的正解

研究一类二阶m-点边值问题u″ f(t,u,u)′=0,00,i=1,…,m-2,ζi满足0=ζ0<ζ1<ζ2<…<ζm-2<ζm-1=1和i∑=1aiζi<1。应用推广的Krasnosel-skii′s不动点定理,给出了上述边值问题至少存在一个正解的充分条件。     

地球模型偏差对远程弹箭弹道仿真的影响及修正

针对地球模型精确度影响远程弹箭弹道仿真的问题,分析了地球模型偏差对弹道仿真精度的影响并加以修正。采用总的地球椭球系,在已有弹道模型的基础上,分析了垂线偏差的产生机理及其对定向定位参数的影响,并由此得出弹道几何偏移随定向偏差的变化规律,研究了引力加速度初值偏差对弹道的误差累积,并对由水准面不平行性造成的实际落点高差进行了理论推导。对比仿真算例表明,考虑地球模型偏差影响的仿真结果与不考虑的情况下差别较明显,在远程条件下对弹道仿真精度的影响不容忽视。     

飞航导弹故障飞行落点概率计算方法

针对飞航导弹故障飞行落点概率难以准确计算的问题,通过分析导弹的各个分系统的故障机理重新提出五种故障模式,依据逐系统串联的原理建立了故障模式的概率分配计算模型;在对发射、飞行和故障后坠落等阶段进行分析的基础上建立各故障模式的仿真模型;最后应用蒙特卡洛方法对某型导弹故障飞行落点的概率分布进行了仿真计算。