磨损身管下的杆式穿甲弹强度失效计算机模拟

针对某型105 mm钨合金超速脱壳穿甲弹在射击试验时出现的弹体强度失效现象,使用有限元分析软件对其强度进行了分析计算。计算分两种工况：正常状态下的弹体应力应变分布和磨损身管条件下的弹体应力应变分布。根据计算结果,证实了弹体强度失效是由于火炮身管过度磨损的原因所致。     

一种新的CLEFIA多字节差分故障分析方法

阐述了CLEFIA分组密码算法及故障分析原理,根据在CLEFIA密码第r轮与第（r-2）轮注入多字节故障,提出了一种新改进的针对CLEFIA的多字节故障模型及分析方法,并通过软件仿真实验进行了验证。结果表明,CLEFIA算法的Feistel结构和差分S盒特性使其易遭受多字节故障攻击,而改进算法使得密钥的恢复效率大大提高。     

基于动力学分析和模糊综合评判的变速箱测点配置

针对变速箱状态检测与故障诊断过程中状态信息获取的测点位置基本靠经验设定,缺少理论支持,导致检测准确性和可靠性不高的问题,在建立变速箱箱体的有限元分析模型的基础上,进行了箱体的约束模态分析,根据模态位移"取大优先"的原则初选10个测点,然后采用模糊综合评判的方法,将测点优化问题转化为方案优选问题处理,提出了变速箱箱体模态实验的测点优化配置方案。结果表明:采用动力学分析和模糊综合评判相结合的方法进行测点优化选择,得到了科学合理的测点优化配置方案。     

立式金属油罐罐壁与底板连接区域强度分析

采用ABAQUS大型非线性有限元软件,在弹性地基的假设下,对10000m3立式金属油罐进行了水试压状态下的强度分析,计算出两种地基条件下底板的轴向位移和罐壁与底板连接区域的应力分布,所得结果与前人研究成果基本吻合,验证了有限元分析的正确性。从罐壁与底板连接区域的应力曲线可以看出,地基状况对该区域的应力大小有着显著的影响,这为进一步研究复杂边界条件下罐底边缘应力分布以及罐基的优化设计提供了参考。     

基于ANSYS的车载式金属油罐有限元分析

利用有限元分析技术,应用ANSYS分析软件对车载式金属油罐罐体的结构强度进行了分析计算,得出在各种工况下的应力分布云图。通过对计算结果的分析,找出了产生最大应力的部位及原因,为金属油罐的优化设计提供了理论依据。     

基于本体的信息与信息空间及其代数结构

实现特定信息环境下基于信息组织的信息资源服务,需要对信息、信息空间有更合适的、形式化的描述。文章基于本体层次对信息、信息的运算、信息之间的关系以及信息空间给出了数学描述并对其代数结构进行了研究。从而为特定信息环境下的信息资源服务提供理论支撑。     

空空导弹越肩发射初制导转弯控制与仿真

针对空空导弹越肩发射初制导俯仰平面180°转弯,提出了一种基于最优控制理论的最优转弯方法,该方法是确定一个最佳推力方向角,使转弯完成时导弹的末端速度最大。建立了简化的用于姿态控制的姿态动力学模型,采用反作用喷气控制系统(RCS)设计了导弹的姿态控制律。对空空导弹180°转弯的飞行过程进行了仿真并给出分析结果。     

Cell structure of microcellular combustible object foamed by supercritical carbon dioxide

In order to solve the issue that the combustible objects for cased telescoped ammunition (CTA) didn't burn completely during the combustion process, the microcellular combustible objects were foamed with numerous cells in the micron order to improve the combustion performance by the supercritical carbon dioxide (SCCO₂) foaming technology. As the cell structure determined the combustion properties of microcellular combustible objects, the solubility of SCCO₂ dissolved into the combustible objects was obtained from the gravimetric method, and scanning electron microscope (SEM) was applied to characterize the cell structure under various process conditions of solubility, foaming temperature and foaming time. SEM images indicate that the cell diameter of microcellular combustible objects is in the level of 1 μm and the cell density is about 10¹¹ cell⋅cm⁻³. The microcellular combustible objects fabricated by the SCCO₂ foaming technology are smooth and uniform, and the high specific surface area of cell structure can lead to the significant combustion performance of microcellular combustible object for CTA in the future.     

Analysis of some critical aspects in hot machining of Ti-5553 superalloy: Experimental and FE analysis

In this study, a newly developed titanium superalloy, i.e., the Ti-5553 alloy has used for hot machining. This material replaced Ti-grade-5 alloy in the application of aerospace, automobile, and biomedical sector. However, similar to Ti-grade-5 alloy, the Ti-5553 alloy has a low thermal conductivity which makes it difficult-to-cut material categories hence, high tool wear, cutting force and bad surface finish. Hot machining of Ti-5553 has been studied at different machining condition (room and hot) using Deform-2D finite element analysis. The result from the simulation test was compared with the experimental value and reduction of cutting and thrust forces was observed. The experiment was carried out with the same input parameters as simulation, and good coherence between them observed. Additionally, cutting zone temperature, effective stress, etc. for both room and elevated the temperature are also discussed.     

卡塞格林结构式平行光管衍射分辨率的研究

对常规结构式平行光管和卡塞格林结构式平行光管的衍射分辨率进行了对比分析。计算了在衍射分辨率的限制下卡塞格林结构式平行光管中间遮挡孔径尺寸与系统整体长度之间的关系。为卡塞格林结构式平行光管的研究、设计提供了必要的依据。