Anti-follower jamming wide gap multi-pattern frequency hopping communication method

This paper deals with the follower jamming (FJ) resistance for the frequency hopping (FH) communication system over additive white Gaussian noise (AWGN) channel. Conventional FH systems are susceptible to be jammed by FJ, and multi-pattern frequency hopping (MPFH) has good resistance to FJ. To further improve the FJ rejection capability of MPFH, we propose a wide gap multi-pattern frequency hopping (WGMPFH) scheme. WGMPFH uses channels to represent messages, and the data channel and complementary channel are hopping on orthogonal frequency slots according to wide gap FH patterns. The transmitted signal lures FJ to aim at the data channel and the complementary channel is away from FJ by adopting wide gap frequency patterns. FJ does not affect the complementary channel but increases the signal energy in the data channel, thus the effect of FJ is reduced. Its bit error rate (BER) is derived under FJ and the effects of three FJ parameters (tracking success probability, jamming duration ratio and jamming bandwidth ratio) on the BER performance of WGMPFH are investigated versus the conventional FH/BFSK and MPFH system. Numerical and simulation results show that when under the worst-case FJ, the proposed WGMPFH outperforms the MPFH by about 1–3 dB and outperforms the conventional FH/BFSK by more than 4 dB. The proposed WGMPFH shows superior jamming rejection performance under FJ especially in severe signal-to-jamming ratio (SJR).     

A high performance waveform and a new ranging method for the proximity detector

Signal modulation is an essential design factor for proximity detectors and directly affects the system’s potential performance. In order to achieve the advantages of chaotic codes bi-phase modulation (CCBPM) and linear frequency modulation (LFM) simultaneously, this paper designed a waveform which combined chaotic codes bi-phase modulation and linear frequency modulation (CCBPM–LFM) for proximity detectors. The CCBPM–LFM waveform was analyzed in the aspect of time delay resolution (TDR) and Doppler tolerance (DT) based on ambiguity function (AF). Then, a ranging method, which we called instant correlation harmonic demodulation (ICHD), was presented for the detector using the CCBPM–LFM waveform. By combining time domain instant correlation with harmonic demodulation, the ICHD solved the problem caused by combination modulation and made the most of the linear frequency modulation (LFM) harmonics and the correlation of chaotic codes. Finally, a prototype was implemented and ranging experiments were carried out. From the theoretical analysis and experimental results, the proximity detector used the CCBPM–LFM waveform has an outstanding detection performance.     

溅板式层板喷注单元燃烧特性数值分析

为了获得喷注单元结构参数对喷注器燃烧特性的影响规律,利用数值分析方法对单喷嘴溅板式层板喷注单元气-气燃烧特性进行研究,考察燃烧室特征长度及出口层喷嘴宽度对气氧/甲烷流动及燃烧特性的影响。在求解气-气燃烧流场方面,采用带化学反应的湍流N-S方程进行描述,其中化学动力学反应模型采用简化的单步9组分模型。研究结果表明:燃烧室特征长度的增大有利于特征速度效率的增加;该条件下采用溅板式层板喷注单元所对应的燃烧室特征长度约为600 mm。对比分析发现,出口层喷嘴宽度取0.15 mm时,水组分摩尔分数与热力计算值差别最大;当其值取1.05 mm时,燃烧室头部区域截面温度上升最快,取0.45 mm时上升最慢。总的来说,出口层喷嘴宽度取0.75 mm时,燃烧长度最短,燃烧效率最大。     

并联放电等离子体合成射流激励器工作特性

等离子体合成射流激励器凭借射流速度高、工作频带宽、响应迅速等优势在高速流场主动流动控制领域具有良好的应用前景。为了克服单个激励器控制能力弱、控制范围窄的缺点,开展了并联放电等离子体合成射流激励器的研究,搭建了最多支持三路并联放电的微秒脉冲电源。测试结果表明,电源在空载及负载条件下可以实现1000 Hz稳定放电。随着放电电容的增大,放电电能的提高,等离子体电弧的温度升高,激励器腔体内气体被加热得更剧烈,产生的射流速度增大。随着工作频率的提高,激励器的击穿电压降低,放电电能减小,射流速度减小。通过对触发信号的调制,可以实现每个激励器的独立控制,使得并联式激励器具有更强的流动控制灵活性。试验结果显示,激励器工作相位与触发相位具有较好的对应关系。     

基于DSP的双伺服驱动系统

针对某型火炮伺服系统的数字化改造,设计了一种基于单片DSP的双伺服驱动系统.本设计利用电机控制专用芯片--TMS320LF2407A,独立输出两路PWM控制信号,分别驱动高低和方位两个伺服电机.功率放大电路采用工作在受限单极倍频可逆PWM控制模式下的H桥结构.试验表明,该数字伺服系统工作可靠、动态响应快、噪音低.     

大挠性太阳能帆板航天器的姿态控制

提出了一种简单有效的抑制太阳能帆板变形振动的PDA控制方法。其特点主要是在航天工程中常用PD方法的基础上,增加了航天器的刚性姿态加速度反馈,该方法经数值仿真和不同的实验系统证明,对大挠性航天器在姿态机动和位置保持控制时是一种简单可行的振动抑制策略,在大挠性航天器变轨和交会对接工程中具有参考价值。     

二次相位误差对FMCW SAR成像质量的影响

调频连续波合成孔径雷达(FMCW SAR)是一种新近提出来的成像雷达体制,在FMCW SAR成像中,相位误差是成像质量下降的主要原因,必须对相位误差进行消除.首先建立了存在二次相位误差的FMCW SAR的信号模型,然后分析了二次相位误差对成像质量的影响,提出了一种补偿二次相位误差的方法.此方法与存在二次相位误差时的成像结果相比较,有效地消除了二次相位误差的影响,成像质量大为提高.     

基于优化初始聚类中心K-Means算法的跳频信号分选

提出了一种优化初始聚类中心的方法.方法通过搜索参数统计直方图峰值预估类数目,并根据峰值位置确定聚类中心大概位置.由于优化的初始类心与实际类心相隔不远,聚类迭代次数大为减少.与传统的优化聚类中心方法相比,本方法计算量更少.最后将改进K-Means聚类算法应用于跳频信号分选,仿真结果表明,分选效果良好.     

一种基于关联度的跳频频率预测方法

对跳频通信进行有效干扰的关键在于对跳频信号频率进行较准确的预测.根据跳频频率序列的混沌特性,并基于混沌系统相空间重构思想,提出了一种基于关联度的跳频频率预测方法,以达到具有较高有效预测概率的目的.仿真实验结果表明,在一定的预测精度要求条件下,该预测方法具有较高的有效预测概率,对跳频通信对抗研究具有借鉴意义.     

警戒雷达情报数据模拟器的设计与实现

针对C3I系统中警戒雷达的扫描跟踪和雷达情报数据录取仪的数据处理以及有线传输功能进行模拟.该模拟系统包括两部分,目标情报数据的产生与数据的调制和输出.应用EVC编程实现了目标情报数据的生成和系统控制,系统数据调制采用2FSK,由FPGA编程实现.应用PC104总线和FPGA技术构建了硬件平台.