Investigation on the process parameters of TIG-welded aluminum alloy through mechanical and microstructural characterization

Multi-pass TIG welding was conducted on plates (15×300×180 mm3) of aluminum alloy Al-5083 that usually serves as the component material in structural applications such as cryogenics and chemical processing industries. Porosity formation and solidification cracking are the most common defects when TIG welding Al-5083 alloy, which is sensitive to the welding heat input. In the experiment, the heat input was varied from 0.89 kJ/mm to 5 kJ/mm designed by the combination of welding torch travel speed and welding current. Tensile, micro-Vicker hardness and Charpy impact tests were executed to witness the impetus response of heat input on the mechanical properties of the joints. Radiographic inspection was performed to assess the joint's quality and welding defects. The results show that all the specimens displayed inferior mechanical properties as compared to the base alloy. It was established that porosity was progressively abridged by the increase of heat input. The results also clinched that the use of me-dium heat input (1-2 kJ/mm) offered the best mechanical properties by eradicating welding defects, in which only about 18.26% of strength was lost. The yield strength of all the welded specimens remained unaffected indicated no influence of heat input. Partially melted zone (PMZ) width also affected by heat input, which became widened with the increase of heat input. The grain size of PMZ was found to be coarser than the respective grain size in the fusion zone. Charpy impact testing revealed that the absorbed energy by low heat input specimen (welded at high speed) was greater than that of high heat input (welded at low speed) because of low porosity and the formation of equiaxed grains which induce better impact toughness. Cryogenic (-196 C) impact testing was also performed and the results corroborate that impact properties under the cryogenic environment revealed no appreciable change after welding at designated heat input. Finally, Macro and micro fractured surfaces of tensile and impact specimens were analyzed using Stereo and Scanning Electron Microscopy (SEM), which have supported the experimental findings.     

Cooperative interception with fast multiple model adaptive estimation

For the case that two pursuers intercept an evasive target, the cooperative strategies and state estimation methods taken by pursuers can seriously affect the guidance accuracy for the target, which performs a bang For the case that two pursuers intercept an evasive target, the cooperative strategies and state estimation methods taken by pursuers can seriously affect the guidance accuracy for the target, which performs a bang-bang evasive maneuver with a random switching time. Combined Fast multiple model adaptive estimation (Fast MMAE) algorithm, the cooperative guidance law takes detection configuration affecting the accuracy of interception into consideration. Introduced the detection error model related to the line-of-sight (LOS) separation angle of two interceptors, an optimal cooperative guidance law solving the optimization problem is designed to modulate the LOS separation angle to reduce the estimation error and improve the interception performance. Due to the uncertainty of the target bang-bang maneuver switching time and the effective fitting of its multi-modal motion, Fast MMAE is introduced to identify its maneuver switching time and estimate the acceleration of the target to track and intercept the target accurately. The designed cooperative optimal guidance law with Fast MMAE has better estimation ability and interception performance than the traditional guidance law and estimation method via Monte Carlo simulation.     

虚拟电流注入法在线补偿转子位置估算误差

旋转高频注入法能估计永磁同步电机零速和低速时的转子位置,但在转子磁极位置解调过程中滤波器的使用会带来较大估算误差。提出虚拟电流注入法来在线补偿转子位置误差,基于估算的转速,构造与负序响应电流同频率的虚拟电流,经过与负序电流完全相同的解调,得到的虚拟电流相位与解调前相位的差值补偿估算的转子位置。分析比较了注入旋转电压导致的实际转速波动和正序响应电流引起的估算转速波动对误差补偿效果的影响,并利用低通滤波器来改善补偿效果。仿真和实验验证了所提方法在电机处于不同状态时对转子位置误差补偿的效果。     

高温燃气与不同构型的再生冷却面板对流传热的数值模拟

对高温燃气与带有平行冷却通道的再生冷却面板之间的三维耦合传热开展了数值研究,其中冷却通道内冷却剂为超临界压力煤油,并结合理论分析探讨了冷却面板构型对耦合传热的影响。结果表明:随燃气侧壁厚以及冷却通道宽度和高度的增大,燃气侧壁面温度升高,热流密度降低。研究还发现:冷却通道不同壁面传递给煤油的热量占比几乎不随燃气侧壁厚变化,但随冷却通道宽度和高度的改变而变化。     

基于多元高斯概率分布的无线局域网定位方法研究

针对无线局域网环境及室内目标定位需求,研究了基于接收信号强度指示的定位技术,提出了一种基于多元高斯概率分布的信号强度模式匹配方法,讨论了定位系统框架。试验结果表明,该方法具有较好的室内定位效果。     

一起管道燃气火灾爆炸事故爆炸点形成原因探讨

通过对一起居民住宅管道燃气泄漏火灾爆炸事故现场破坏程度的勘查,分析了在管道燃气泄漏后,由于燃气化学组分和理化性质的不同,室内环境因素影响扩散条件的不同,不同浓度的爆炸性混合气体在不同的部位出现了不同的形成过程,从理论上论证了管道燃气的泄漏点不一定就是中心爆炸点的火灾现场现象。     

基于贝叶斯方法的指数寿命型产品可靠度评估方法

以经典法为推理基础,利用无验前信息时验前分布密度的假设方式及共轭分布函数的传递性,推导出指数寿命型产品在不同试验方案下可靠度R的多层贝叶斯评估方法。使得在利用贝叶斯方法对指数寿命型产品进行评估时,更具科学性和合理性。     

直扩信号侦收技术研究

DS信号是一种具有优良电子防御能力的新型通信信号,广泛运用于军事、民用通信系统中。对抗这种技术的侦察手段目前还没有取得实用性的进展,因此,需开展大量的理论和实践工作。总结了在低信噪比下对直接序列扩频信号侦收的方法,并比较各个方法的优缺点,探讨了其中一些关键问题和新技术途径。     

多元先验信息的融合问题

在多元先验信息条件下,运用Bayes理论讨论问题时,必然会遇到先验信息融合问题.文中提出了几种简化形式,并针对产品失效率的多个先验信息情形,结合实例与熵度量的拟合优度说明了该方法的合理性.     

残差GM（1，1）模型在恒加试验中的应用

介绍了目前恒加试验中,正常应力水平下特征寿命点估计的数据统计分析方法及其不足。针对恒加试验的特点和所需解决的问题,基于灰色预测理论的残差GM(1,1)模型,给出了一种新的求解方法。最后分别运用三种不同的方法对给出的应用实例进行正常应力水平下特征寿命值的求解,证明了本文所给出的方法确实可行。