Ballistic impact properties of woven bamboo- woven E-glass- unsaturated polyester hybrid composites

In this study, a laminated woven bamboo/woven E glass/unsaturated polyester composite is developed to combat a ballistic impact from bullet under shooting test. The aim of this study is to understand the fundamental effects of the woven bamboo arrangement towards increasing ballistic resistance properties. The work focusses on the ballistic limit test known as NIJ V50, which qualifies materials to be registered for use in combat armor panels. The results show that the composites withstood 482.5 m/s ± 5 limit of bullet velocity, satisfying the NIJ test at level II. The findings give a strong sound basis decision to engineers whether or not green composites are qualified to replace synthetic composites in certain engineering applications.     

Synergistic effect of hybrid Himalayan Nettle/Bauhinia-vahlii fibers on physico-mechanical and sliding wear properties of epoxy composites

The cellulosic bast fibers are recognized as a justifiable and biodegradable substitute for producing moderate strength polymer composite materials because of their characteristics of renewability, eco-friendliness, and higher specific strength. Hence the aim of this research work is to fabricate Himalayan bast fibers (Nettle fiber (NF)/bauhinia vahlii fiber (BF)) based mono/hybrid epoxy composites at varying weight percentage of 2–6 wt% and evaluate the physical (void fraction and water absorption), mechanical (tensile strength, flexural strength, hardness) and sliding wear properties of as-fabricated composites. The 6 wt% NBF reinforced composites exhibited higher mechanical properties as compared to NF and BF composites with tensile strength of 34.04 MPa, flexural strength of 42.45 MPa, and hardness of 37.01 H_v respectively. The influence of various control factors (sliding velocity, NF/BF/NBF contents, normal load and sliding distance) on specific sliding wear rate of composites was evaluated by Taguchi (three factors at three levels) experimental design and the percentage contribution of these selected parameters on sliding wear performance was examined by Analysis of variance (ANOVA). The sliding wear property of as-developed composites was found to be greatly influenced by sliding velocity and the wear resistance was observed to be improved with the NF/BF/NBF contents. The wear mechanism of the as-fabricated composites has been elucidated by scanning electron microscopy analysis. The research outcomes demonstrated that the hybridization of Bauhinia vahlii fiber with Nettle fiber led to improve the mechanical and wear properties of epoxy composites.     

拉锥光纤耦合的光放大器组件光损耗分析

介绍了拉锥光纤耦合的SOA组件的结构特点 ,并针对该结构计算分析了光耦合损耗的最小值 .为了进一步减小SOA组件的光耦合损耗 ,提出了不对称形式的拉锥光纤耦合的SOA组件结构 .这在原有的制作工艺技术条件下 ,可以将整个组件的光耦合损耗降低 1dB .     

磺化酚醛树脂的研究:高效减水剂的制备及其对混凝土工作度和力学性能的影响

制备了以磺化酚醛树脂为基础的3种高效减水剂,该高效减水剂能显著地减少用水量和改善混凝土工作度以及力学强度.测试结果显示:随掺量的增加,混凝土抗压强度在一定范围内有明显的提高,然后增加较慢或有所下降;混凝土的抗折、抗拉、抗剪强度以及与钢筋的粘接强度均高于对照空白样.同硅灰、磨砂矿渣相结合还获得了抗压强度大于100MPa、流动性好的超高强混凝土.     

光纤通信系统用减反膜的研究

针对WDM光纤通信系统对具有极高透过率的光学薄膜元件的需要,系统地研究了增透膜的设计与镀制.采用统计实验求总极值法和Powell最小二乘法相结合的多级优化方法编制程序,完成了以BK7玻璃为基底的增透膜的膜系设计,采用多种监控方法完成了此类非规整膜系的镀制实验.测试结果表明,采用变过正量极值法监控非规整膜系的镀制,可精确控制各层膜的光学厚度,获得在1550nm波段附近具有很高透过率的光学薄膜元件.     

型钢混凝土桁架节点有限元分析

由于普通结构设计软件无法实现型钢混凝土空间桁架节点内部细化计算分析,为解决这一问题,通过采用ANSYS软件对整体结构进行静力分析,并提取桁架节点处各构件的内力,将其施加于桁架节点的实体模型,进行精细的有限元计算分析;检验桁架节点实体模型内部应力是否满足强度要求,验证结构设计时节点区域的型钢选取和配筋的合理性;同时将分析结果与在该结构施工现场实际检测结果进行对比。结果表明,AN—SYS软件能够准确地完成普通结构设计软件无法完成的复杂结构模型的细化有限元分析。     

高掺量碳纤维增强活性粉末混凝土力学性能实验

采用一种新的碳纤维自分散工艺和专用分散设备制备出了掺量达胶结材质量8％的碳纤维增强活性粉末混凝土;研究了碳纤维掺量对活性粉末混凝土的力学性能影响规律。实验结果表明,在碳纤维掺量高时,活性粉末混凝土的力学性能受碳纤维掺量和水胶比两个因素共同作用。     

光纤光栅与分布式光纤感温探测性能研究

传统的火灾自动报警系统工作时需要向现场探测器供电。带电类探测器工作在易燃易爆场所必然存在着不安全因素,而利用光纤光栅及分布式光纤感温探测元件构成的火灾探测报警系统采用光信号测量与传输,实现了探测现场无电检测,从而真正实现了本质安全防爆。在分析光纤光栅与分布式光纤感温探测机理的基础上,通过对比探讨了各自的应用特性。     

轻质夹层复合吸声结构的制备工艺和水声性能

夹层复合吸声结构具有很强的可设计性,得到广泛的应用,但以往研究的此夹层结构的吸声芯材存在密度较大的问题。为此,设计了一种轻质夹层复合吸声结构,对该结构的制备工艺特别是芯材的制备工艺进行了设计,用玻璃钢作为表层材料、用柔性环氧树脂和聚氨酯改性环氧树脂的混合物为基体、空心玻璃微珠为填料、593和聚醚胺为固化剂所制备的多孔复合材料作为芯材来制备夹层复合吸声结构,制作了该结构的声学测试试件,在脉冲声管中测试了其水下声学性能。结果表明:所设计的夹层复合吸声结构具有较低的密度和良好的吸声性能,证明了该制备工艺设计的合理性。     

光纤陀螺在车载惯性平台稳定回路中的仿真

为了延长车载惯性平台的使用寿命并提高其稳定精度,在原有平台机械结构的基础上,提出采用光纤陀螺代替原有的挠性陀螺作为惯性平台的敏感元件,并重新建立了平台系统稳定回路的数学模型。仿真研究表明该数字稳定回路具有较好的动态和稳态性能,能够满足系统的设计要求。经实验验证,该光纤陀螺惯性平台系统已实现功能要求。