Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Formation of adiabatic shearing band for high-strength Ti-5553 alloy: A dramatic thermoplastic microstructural evolution

By using split Hopkinson pressure bar, optical microscopy and electronic microscopy, we investigate the influence of initial microstructures on the adiabatic shear behavior of high-strength Ti–5Al–5V–5Mo–3Cr (Ti-5553) alloy with lamellar microstructure and bimodal microstructure. Lamellar alloy tends to form adiabatic shearing band (ASB) at low compression strain, while bimodal alloy is considerably ASB-resistant. Comparing with the initial microstructure of Ti-5553 alloy, we find that the microstructure of the ASB changes dramatically. Adiabatic shear of lamellar Ti-5553 alloy not only results in the formation of recrystallized β nano-grains within the ASB, but also leads to the chemical redistribution of the alloying elements such as Al, V, Cr and Mo. As a result, the alloying elements distribute evenly in the ASB. In contrast, the dramatic adiabatic shear of bimodal alloy might give rise to the complete lamination of the globular primary α grain and the equiaxial prior β grain, which is accompanied by the dynamic recrystallization of α lamellae and β lamellae. As a result, ASB of bimodal alloy is composed of α/β nano-multilayers. Chemical redistribution does not occur in ASB of bimodal alloy. Bimodal Ti-5553 alloy should be a promising candidate for high performance armors with high mass efficiency due to the processes high dynamic flow stress and excellent ASB-resistance.     

节点非独立失效下的局域网可靠性建模与分析

以具有层次结构的局域网作为拓扑模型,考虑共因失效和关联失效这2类节点非独立失效事件发生的情况,建立了交换机节点失效模型来模拟交换机失效,利用Monte-Carlo仿真算法近似计算出网络的两端可靠性,研究2种共因失效事件和3种关联失效事件对网络端端可靠性的影响。结果表明:因资源节点出现故障和协议层出现错误而导致交换机失效的共因失效事件均会降低网络可靠性,且资源节点失效概率或协议层失效概率越大,网络可靠性越低;而由于使用了热备份技术、堆叠技术以及发生广播风暴导致的关联失效事件,即使节点独立失效概率很小,只要相关因数足够大,故障都会快速传播,导致网络可靠性迅速下降。     

基于信息论的C3I系统决策性能的评价

信息熵是描述信息系统的一种比较成功的方法.采用信息论的方法对决策系统进行描述,在考虑了决策者的有界合理性限制和达到满意性能指标的要求下,分析了单人指挥决策系统的系统性能,并在此基础上分析了多人指挥决策系统的系统性能,最后得出采用决策系统的误差概率P和相互一致性度量Q作为评价C3I系统决策性能标准的结论.     

基于DIFHA算子的动态直觉模糊多属性群决策方法

动态决策问题是现实中的一类常见问题。在提出动态直觉模糊混合平均(D IFHA)算子的基础之上,提供一种动态直觉模糊多属性群决策方法。该方法能同时考虑决策过程的阶段性和属性值位置对决策结果的影响,并较好地处理决策过程中的定性指标。分析和算例证实该方法的可行性和实用性。     

速率陀螺解相遇与敌我态势的关系

根据敌我相对运动的原理,导出速率陀螺测量出的目标俯仰角速度Ω_s、测向角速度Ω_L 和探测器测出的距变率与敌我姿势要素间的关系,提出了距变率在极短时间内保持不变的条件;并利用Ω_s、Ω_L 和有关数据(qw,ε、D、■、V_w、K_w)推导出在不满足“快解”条件时计算目标运动要素和弹丸发射诸元的计算公式。     

59-03指挥仪动态调整专家系统

本文介绍了59-03指挥仪动态调整专家系统的设计过程,重点讨论了应用故障诊断的测前模拟理论建立指挥仪动态调整专家系统的方法。     

Weibull型产品的可靠性验证

讨论了Weibull型产品的可靠性验证问题 ,首先分析了Weibull型产品分布参数的无信息验前分布问题 ,利用验前信息可以得到分布参数的验前概率密度函数 ,进而分析了产品的可靠性验证问题 ,顾及了使用方利益和生产方利益。仿真算例表明 ,使用方利益和生产方利益是相互折衷的。     

在热处理领域应用可靠性理论的研究

本文提出以最小失效概率为标准,解决钢材强韧性最佳匹配问题,并以此来优选钢材的回火温度或淬火温度。本文将可靠性理论引入热处理领域,以强度理论和断裂力学为依据,应用干涉模型和最弱环模型,在一定条件下计算出各种状态下材料的一系列综合失效概率,进而找出具有最小失效概率的状态,即为此条件下最佳强韧性匹配的状态,也就是我们应当优选的状态。     

微元内破片平均杀伤概率估算的新方法

本文提供了一种在弹药破片杀伤面积的估算中,求取微元内破片平均杀伤概率估值的新方法,这种方法可以保证在较小工作量的条件下提高估值精度.