二维超声速空气引射器启动特性试验研究

超声速引射器是高空模拟试车台的重要组件,在发动机启动前利用引射器对试验舱预抽真空,可避免发动机启动初始时刻燃气漏入试验舱造成燃气在发动机中分离,对获取发动机在高空环境下的完整推力特性具有重要意义。而该工况下超声速引射器的启动过程是引射器工作过程中最为恶劣的工况,设计不合理的引射器会导致启动压力过高甚至不能实现启动。建立了缩比超声速空气引射器试验台对超声速引射器的启动特性进行研究,采用压力测量方法结合纹影技术对超声速引射器处于极限启动压比时的流场进行了描述,研究结果表明混合室收缩比越小,引射器极限启动压比越低。同时给出了定位超声速引射器不启动原因的判据:当引射器不启动是由引射总压不足引起时,盲腔压力在引射总压提高时降低,并在临界启动状态下达到最小值;而由混合室收缩比过小导致的引射器不启动在引射总压提高时盲腔压力单调上升。     

基于并行模拟的多核集群系统性能预测和分析

针对多核集群系统所表现出的新的性能特征,提出了面向多核集群系统消息传递应用程序的并行模拟模型并设计、实现了一个并行模拟器MCPSim(Multi-core Cluster Parallel Simulator),MCPSim在功能模型和性能模型上体现了片内核间、结点内片间以及结点间等三个层次上消息通信的特点,同时支持对应用的消息数量、通信量等的百分比分布的profiling功能,采用PRIMEJ、acobi3D、NPB IS以及HPL等Benchmark程序对MCPSim进行了测试,结果表明MCPSim性能预测的精度优于BigSim,同时能够广泛应用于针对多核集群系统消息传递应用程序的性能分析中。     

C2组织探索性分析框架设计研究

以验证组织优化设计方法为目的,将探索性分析思想引入组织优化设计研究,根据探索性分析的特点与组织优化设计方法验证的具体需要,对C2组织探索性分析的过程进行了研究,初步设计了面向C2组织的探索性分析框架并对其中的关键技术进行了分析。     

目标通视性检测建模与仿真

在战斗机对地攻击选择武器投放位置以及巡航导弹选择地标点时,必须验证其选择位置的合理性,因此通视性检测是战斗机对地攻击规划的关键技术之一。提出了一种目标通视性检测的建模方法,分析了地形遮蔽盲区构成因素,给出了数字地图处理方法,建立了地形遮蔽盲区计算模型及发现目标概率模型,实现了目标的通视性检测,并进行了仿真验证。该模型为战斗机对地攻击选择武器投放位置和验证导弹地标点选择合理性提高了方法。     

基于复杂网络的作战网络分析

分布式网络化作战是网络中心战的基础,而分布式作战网络的构建是网络化作战的重要前提。首先,运用复杂网络的相关参数分析了多种不同的网络,选择了BA非标度网络作为分布式作战网络的最优表现形式;其次,以BA非标度网络为基础提出了一个适合军事上动态鲁棒性分析的模型DCNCE;最后,仿真结果表明,在以网络效能值为测度的对比下,分布式作战网络在介数毁伤策略下更脆弱,为构建并改进现有的作战网络提供了理论依据。     

助推滑翔飞行器复合控制系统线性化小偏差运动方程推导与控制系统设计

助推滑翔技术是制导武器实现增加射程、提高机动突防能力的关键技术之一,对飞行器姿态控制有较高的要求,需要设计复合控制方式的姿态控制系统.针对采用空气舵与燃气舵联动控制的飞行器,建立了动力学模型,详细推导了完整的三通道线性化小偏差运动方程,结合典型弹道数据给出了动力系数图像,分析了助推滑翔弹道各飞行段中飞行器的稳定性,在此基础上选取再入段低空飞行特征点进行了姿控系统设计,仿真结果验证了线性化小偏差运动方程的正确性和控制系统的有效性,为进行此类飞行器的稳定性分析与姿态控制系统设计提供了有益的参考.     

智能化作战指挥模式需求

智能装备已经走入军队、走向战场,创建智能化作战指挥模式是智能化时代作战指挥的必然发展趋势,智能化作战指挥模式需求分析可为智能作战问题研究提供有效的信息。智能化作战指挥模式的需求分析已经具备了一定的物质、理论和技术基础,同时,也具有了一定的构建思路、实践条件和实验平台。在此基础上,本文从军事需求、功能需求和技术需求以及构建要求四个不同角度进行需求分析,以找准创建需求,为后续工作进一步展开奠定基础。     

Analysis of some critical aspects in hot machining of Ti-5553 superalloy: Experimental and FE analysis

In this study, a newly developed titanium superalloy, i.e., the Ti-5553 alloy has used for hot machining. This material replaced Ti-grade-5 alloy in the application of aerospace, automobile, and biomedical sector. However, similar to Ti-grade-5 alloy, the Ti-5553 alloy has a low thermal conductivity which makes it difficult-to-cut material categories hence, high tool wear, cutting force and bad surface finish. Hot machining of Ti-5553 has been studied at different machining condition (room and hot) using Deform-2D finite element analysis. The result from the simulation test was compared with the experimental value and reduction of cutting and thrust forces was observed. The experiment was carried out with the same input parameters as simulation, and good coherence between them observed. Additionally, cutting zone temperature, effective stress, etc. for both room and elevated the temperature are also discussed.     

Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

Estimating failure time distribution and its parameters based on intermediate data from a Wiener degradation model

Instead of measuring a Wiener degradation or performance process at predetermined time points to track degradation or performance of a product for estimating its lifetime, we propose to obtain the first‐passage times of the process over certain nonfailure thresholds. Based on only these intermediate data, we obtain the uniformly minimum variance unbiased estimator and uniformly most accurate confidence interval for the mean lifetime. For estimating the lifetime distribution function, we propose a modified maximum likelihood estimator and a new estimator and prove that, by increasing the sample size of the intermediate data, these estimators and the above‐mentioned estimator of the mean lifetime can achieve the same levels of accuracy as the estimators assuming one has failure times. Thus, our method of using only intermediate data is useful for highly reliable products when their failure times are difficult to obtain. Furthermore, we show that the proposed new estimator of the lifetime distribution function is more accurate than the standard and modified maximum likelihood estimators. We also obtain approximate confidence intervals for the lifetime distribution function and its percentiles. Finally, we use light‐emitting diodes as an example to illustrate our method and demonstrate how to validate the Wiener assumption during the testing. © 2008 Wiley Periodicals, Inc. Naval Research Logistics, 2008