Thermal hazard assessment of TKX-50-based melt-cast explosive

In the present study, thermal hazards of TNT and DNAN used as the molten binder in TKX-50-based melt-cast explosives were comparatively studied through accelerating rate calorimeter (ARC) and Cook-off experiments. Two kinds of ARC operation modes were performed to investigate the thermal safety performance under adiabatic conditions (HWS mode) and constant heating (CHR mode). The obtained results demonstrated that at both heating modes, DNAN/TKX-50 outperformed TNT/TKX-50 from the thermal safety point of view. However, the sensitivity to heat of the samples was reverse because of the different heating modes. In addition, the results of thermal hazard assessment obtained from the cook-off experiment complied with ARC analysis which indicated the molten binder TNT replaced by DNAN would reduce the hazard of the TKX-50 melt cast explosive. Furthermore, the results of cook-off experiments also showed that DNAN/TKX-50 outperformed TNT/TKX-50 from the aspect of thermal stability, which was consistent with the result of CHR mode because of the similar heating process.     

Analysis on damage characteristics and detonation performance of solid rocket engine charge subjected to jet

To further explore the damage characteristics and impact response of the shaped charge to the solid rocket engine (SRE) in storage or transportation, protective armor was designed and the shelled charges model (SCM)/SRE with protective armor impacting by shaped charge tests were conducted. Air overpressures at 5 locations and axial acceleration caused by the explosion were measured, and the experimental results were compared with two air overpressure curves of propellant detonation obtained by related scholars. Afterwards, the finite element software AUTODYN was used to simulate the SCM impacted process and SRE detonation results. The penetration process and the formation cause of damage were analyzed. The detonation performance of TNT, reference propellant, and the propellant used in this experiment was compared. The axial acceleration caused by the explosion was also analyzed. By comprehensive comparison, the energy released by the detonation of this propellant is larger, and the HMX or Al particles contained in this propellant are more than the reference propellant, with a TNT equivalent of 1.168–1.196. Finally, advanced protection armor suggestions were proposed based on the theory of woven fabric rubber composite armor (WFRCA).     

钢丝增强复合条带抗弹性能数值分析

为研究钢丝增强聚合物基复合条带的抗弹性能,基于冲击动力学理论分析其抗弹机理,再借助ANSYS/LS-DYNA软件和LS-PrePost前后处理器模拟有无增强钢丝2种工况下,条带对7.62 mm弹体的冲击响应。分析表明：条带的弹性模量、剪切模量和面密度会影响其能量吸收性能,能量吸收量随三者的增大而增大;由于聚合物基体的正交各向异性,应力云图显示出扁平椭圆状是合理的;在聚合物基复合条带中嵌入增强钢丝对条带整体的抗弹性能有积极的影响,但嵌入过量的钢丝会导致重量和成本的增加,因此需要对合理的钢丝配比率作进一步研究。研究结果可为钢丝增强聚合物基复合条带在野战防护结构中的应用提供参考。     

Experiment and simulation of launching process of a small-diameter steel cartridge case

In order to explore the rules of the deformation force during the launching of a small-diameter steel cartridge, the semi-closed bomb test method is used to test the greatest strains on chamber outer wall under the different chamber pressures. The pressure curves of cartridge chamber are measured in experiment, and the tensile test data of cartridge are loaded into the numerical calculation to compare with the experimental data. The conclusion was obtained that the calculated results match better with the experimental results by considering strain rate bilinear kinematic hardening material constitutive model. The forces on the various parts of the cartridge during launching and their deformation rules are achieved, in which the equivalent plastic strain decreases and the cylinder ring withstands the maximum equivalent stress when the cartridge case clings to the bore from the mouth to the bottom.     

On the continued acceleration of bomb casing fragments following casing fracture

It has been said that, once a bomb casing has fractured, “detonation gases will then stream around the fragments or bypass them, and the acceleration process stops there.” However, while apparently copious gas flow through casing fractures indicates some pressure release, it is also an indication of significant gas drive pressure, post casing fracture. This paper shows two approaches to the problem of calculating the actual loss of drive. One presents first-order analytical calculations, in cylindrical geometry, of pressure loss to the inside surface of a fractured casing. The second shows the modelling of a selected example in the CTH code. Both approaches reveal that gas escape, while occurring at its own sound-speed relative to the adjacent casing fragments, has to compete with rapid radial expansion of the casing. Together with some historic experiments now publicly available, our calculations indicate that post-fracture casing fragment acceleration is, for most systems, unlikely to be reduced significantly.     

二维拉格朗日和欧拉结合法在流处理器MASA上的实现与评测

现代半导体工艺技术的发展使得在单芯片上放置数百个运算单元成为可能,但是全局片上片外带宽受限。通用处理器体系结构不能较好地适应变化,仍然依靠全局片上结构,少量的运算单元。而流体系结构拥有大量的运算单元、鲜明的存储层次,使得在有限的片外带宽下,用高的本地带宽来满足大量运算单元的需求。首先介绍了原型MASA流体系结构,然后给出了爆轰流体力学中的二维拉格朗日和欧拉结合法(Ygx2)在流体系结构上实现的实例研究,最后用时钟精确的模拟器来评测应用的运行性能,结果表明Ygx2应用在500MHz的MASA上运行结果与1.6GHz的Iantium2的比较快近4倍,证实了流体系结构在高性能计算领域的极大潜力。     

机载航电系统射频隐身性能多域联合评估方法

针对机载航电系统自身辐射源特性,提出一种不依赖敌方探测设备的机载航电系统射频隐身性能评估方法。分析机载航电系统设备在极化域、波形域、能量域中影响射频隐身性能的因素,构建极化域、能量域、波形域射频隐身指标,打破常规的"辐射-接收"模型的隐身性能评估方法,建立基于机载航电系统自身辐射信号工作状态和工作参数的射频隐身定量评估方法。对机载雷达系统进行仿真评估,结果表明,该评估方法能正确反映机载雷达系统的射频隐身性能。     

金属复合板的消防安全性能探讨

随着我国科技进步及建筑节能需要,特别是近年钢结构建筑体系的推广,金属复合板得到迅猛发展。从分析金属复合板的材料性能和火灾特点入手,就工程施工、使用过程中存在的消防安全问题及防范措施进行了探析。     

基于仿真和熵权的VOIP业务网络性能评价权重确定方法

针对目前网络性能评价中多元指标之间权重难以确定的问题,将信息熵理论应用于网络性能评价中.提出采用熵权方法确定指标权重,进而对网络性能进行评价的方法.为了获取反映不同网络状态的性能数据,采用网络仿真方法获得计算熵权所需的样本.实例表明,信息熵能够客观地反映各指标贡献信息量的大小,基于信息熵的熵权能够客观反映各指标的相对重要程度.     

设计参数对一包TI蜗杆传动啮合性能的影响

从齿面接触分析的角度,分析了设计参数中心距、模数和蜗轮齿宽对一包TI蜗杆传动啮合性能的影响。结果表明：相对于理想啮合情况,在蜗轮分度圆直径一定的情况下,较大的中心距及较小的模数可以获得较理想的接触线的形状及分布;蜗轮齿宽的变化对接触线和啮合界限线的分布规律没有影响,但会影响接触线的长度。这些结论为合理选择设计参数提供了理论指导。