碳纤维增强聚合物基复合材料频率选择表面的电磁传输特性

为了避免采用金属频率选择表面制备的天线罩中存在的热残余应力和弱黏接界面等问题,采用与聚合物基复合材料罩壁结构相容性好的碳纤维增强聚合物基复合材料制备频率选择表面,利用自由空间法对试样的电磁传输性能进行测试,并采用数值分析模型对碳纤维复合材料频率选择表面的电磁传输机制和电磁传输影响因子进行分析。结果表明:碳纤维复合材料频率选择表面具有频率选择功能,但谐振频率处的电磁传输损耗较大;通过改变复合材料频率选择表面的单元缝隙率、厚度、电导率以及介电常数可以实现对其电磁传输性能的调节。     

树脂浸渍裂解对气相硅反应渗透C/SiC的影响

粘胶基碳纤维毡经过CVD工艺进行沉积碳增密处理后,采用酚醛树脂浸渍—裂解对C/C素坯的密度进行调节,通过气相硅渗透反应工艺制备了C/SiC复合材料。研究了树脂浸渍—裂解对C/C素坯密度和气孔率的影响规律,分析了树脂裂解碳对C/SiC显微形貌和力学性能的影响。结果表明:随着树脂浸渍—裂解循环次数的增加,素坯密度增加,孔隙率降低;裂解碳含量为27wt%时,C/SiC复合材料的强度和模量达到最大,分别为231MPa和209GPa。通过控制裂解碳含量,可以实现对C/SiC复合材料力学性能和微观结构的裁剪。     

【专栏】飞机结构静强度应变现场测试手段展望

目前飞机结构静强度应变现场主要的测试手段为使用电阻应变计测量系统,但电阻应变计测量系统存在抗电磁干扰差、引线过多以及一致性难以保证等问题,测试效果难以保证。近年来,光纤传感以及非接触光学测量手段的迅速发展,为飞机结构静强度应变现场测试提供了多种选择。本文通过分析以数字图像相关法技术为代表的新技术的特点,如通过进行非接触操作消除安装过程中所带来的分散性误差以及不确定性,在应对某些需要定性分析的飞机静强度试验场合时可以实时给出三维应变和位移场数据,使测量技术更加直观,以及可溯源性更好、更容易保证计量特性的稳定等,对未来飞机结构静强度应变现场测试手段进行了展望,以期为相关部门和机构提供参考。     

An investigation on anti-impact and penetration performance of basalt fiber composites with different weave and lay-up modes

The woven basalt fiber composites (WBFC) and the unidirectional [0°/90°/45°/-45°]_s basalt fiber composites (UBFC) were prepared by hot-pressing. Three-point bending test, low velocity impact test, and ballistic test were performed to the prepared composites. After the tests, the specimens were recovered and analyzed for micromorphology. Three-point bending tests show that both the bending strength and stiffness of the WBFC surpass those of the UBFC. Low velocity impact test results show that the low velocity impact resistance to hemispherical impactor of the UBFC is higher than that of the WBFC, but the low velocity impact resistance to sharp impactor of the UBFC is lower than that of the WBFC. For the ballistic test, it can be found that the ballistic property of the UBFC is higher than that of the WBFC. After the tests, microscopic analysis of the specimens was applied, and their failure mechanism was discussed. The main failure modes of the UBFC are delamination and fibers breakage under the above loading conditions while the main failure mode of the WBFC is fibers breakage. Although delamination damage can be found in the WBFC under the above loading conditions, the degree of delamination is far less than that of the UBFC.     

Microstructural characterization of silicon carbide reinforced dissimilar grade aluminium explosive clads

Aluminium composites are inevitable in ship building, commercial and defence aircrafts construction due to their light weight, high strength to weight ratio, admirable properties and cost affordability. In this study, the microstructural characteristics of explosive cladded dissimilar grade aluminium (Al 1100-A1 5052) clad composites reinforced with silicon carbide (SiC) particles is presented. Microstructure taken at the interface by optical and scanning electron microscopes (SEM) revealed the formation of a silicon carbide layer between the dissimilar grade aluminium sheets. Though reaction layers were witnessed at few locations along the interface, the diffusion of atoms between the participant metals is not visible as confirmed by energy dispersive spectroscopy, elemental mapping, line analysis and X-ray diffraction (XRD). The variation in microhardness at various regions of the silicon carbide reinforced dissimilar aluminium explosive clad is reported. The increase in tensile strength of the SiC laced clad is also presented.     

SiC纤维表面CVD SiC涂层对其单丝强度的影响

采用化学气相沉积(CVD, Chemical Vapor Deposition)工艺在KD-I型SiC纤维表面制备了SiC涂层,选择2h、4h、6h和8h四个时间点研究了沉积时间对纤维性能的影响.结果表明:具有CVD SiC涂层的SiC纤维较无涂层的纤维来说强度有所下降;在所研究的沉积时间范围内,随着沉积时间的增加,涂层的厚度有所增加,涂层由不连续的岛状转变为连续层状,纤维的单丝强度出现了先升后降的趋势.     

几种带补偿功能的三光纤传感器的分析

在单光纤对光耦合模型的基础上 ,研究了三种带补偿功能的三光纤反射式位移传感器 ,建立了通用的光耦合的数学模型。仿真研究了它们的位移特性 ,并比较了它们的优缺点。研究结果表明 ,采用三光纤的光纤位移传感器不但线性范围、位移灵敏度和线性度等特性得到较好改善 ,而且可以有效地消除光源功率波动和反射面的反射率变化等因素对位移测量的影响     

一种强度补偿反射式光纤位移传感器的研究

:提出一种等间距排列的三探头反射式光纤位移传感器 ,该传感器通过双路接收的方法来实现光强补偿。从理论上对该种传感器的补偿机理作了详细的分析 ,得出了位移特性调制函数的表达式 ,给出了仿真曲线。结果表明 ,这种光纤传感器可以有效地消除因光源光强波动、表面反射率以及光纤传输损耗的改变对输出特性的影响     

光纤布拉格光栅的光学特性及其应用

介绍了光纤布拉格(Bragg)光栅的种类和制作,用耦合波理论分析了其基本的光反射性质,包括峰值反射率和反射半高全宽度,结果表明光纤Bragg光栅拥有独特的光反射特性.同时对光纤Bragg光栅在光纤通信、光纤传感器、滤波器等方面的应用进行了介绍和展望,表明光纤Bragg光栅将对整个光纤技术领域产生重要影响.     

正弦波调制的光纤环本征频率测量方法

为了弥补传统光纤环本征频率测量方法中方波调制存在死区的缺陷,提出正弦波调制的本征频率测量方法。对正弦波调制下的光纤陀螺输出信号进行分析,得到二次谐波幅度与调制频率间的二次函数关系,通过计算抛物线顶点即可求得本征频率。依据该原理对已有的光纤陀螺进行升级改造,研制了一套本征频率测量系统。试验结果表明:该方法可达到1×10-5的测量精度,是一种成本低、精度高的光纤环本征频率测量方法。