高速水射流倒空弹体装药安全性研究

本文阐述了高速水射流倒空弹体装药的机理,建立了确定水射流引爆炸药的临界速度的模拟实验方法和模型,进行了高速水射流冲击炸药的安全性试验,并对试验结果进行了分析,证明在工作泵压下高速水射流倒空弹体装药安全、可靠。     

引信全电子安全系统失效分析及评估

本文根据全电子安全系统的一般结构模式,分析了其安全性设计的一般特点和可能造成其失效的各种原因,并在此基础上建立了全电子安全系统的失效故障树,给出了失效概率的定量计算结果。     

聚能射流形成过程的理论建模与分析

分析了聚能射流的形成过程,并对其中的各阶段进行了详细建模。在模型中考虑了炸药爆轰、金属的驱动、药型罩压垮以及射流和杵体的形成过程。采用该模型对某一聚能装药结构进行了计算,计算结果表明:药型罩顶部和底部微元的压垮速度较小,在射流头部形成反向速度梯度,与试验数据吻合较好。该模型对于多级侵彻战斗部的工程设计与侵彻参数的计算具有一定的参考价值。     

采用射流掺混增强的前可调面积涵道引射器数值模拟

为了提高风扇外涵和核心机驱动风扇级外涵流体的掺混效率,提出一种采用射流掺混增强的前可调面积引射器设计方案。通过数值模拟的手段对流量特性、流动掺混和总压损失等方面进行了研究,并同基准模型进行了对比分析,结果表明：采用波瓣混合器结构的前可调面积引射器设计,显著地增加了较高出口背压工况下风扇外涵的流通能力;新的设计方案不仅没有增加低出口背压工况下的总压损失,还减小了高背压出口工况下的流动损失;流向涡的特征尺度是提高掺混效率的关键,可以进一步优化波瓣混合器几何轮廓,以满足调节机构对结构设计的要求。     

Effect of wave shaper on reactive materials jet formation and its penetration performance

Wave shaper effect on formation behavior and penetration performance of reactive liner shaped charge (RLSC) are investigated by experiments and simulations. The reactive materials liner with a density of 2.3 g/cm³ is fabricated by cold pressing at a pressure of 300 MPa and sintering at a temperature of 380 °C. Experiments of the RLSC with and without wave shaper against steel plates are carried out at standoffs of 0.5, 1.0, and 1.5 CD (charge diameter), respectively. The experimental results show that the penetration depths and structural damage effects of steel plates decrease with increasing the standoff, while the penetration depths and the damage effects of RLSC without wave shaper are much greater than that with wave shaper at the same standoff. To understand the unusual experimental results, numerical simulations based on AUTODYN-2D code are conducted to discuss the wave shaper effect, including the propagation behavior of detonation wave, the velocity and temperature distribution of reactive jet, and penetration depth of reactive jet. The simulations indicate that, compared with RLSC without wave shaper, there is a higher temperature produced inside reactive jet with wave shaper. This unusual temperature rise effects are likely to be an important mechanism to cause the initiation delay time of reactive jet to decline, which results in significantly decreasing its penetration performance.     

煤层气加气站火灾爆炸危险性分析及消防对策

根据太原市煤层气加气站的具体情况,从设备安全、规范化安全管理等方面分析了CNG加气站的火灾爆炸危险性,探讨煤层气加气站消防安全的技术措施及对策。     

运动潜体湍流尾迹的SAR遥感仿真研究

采用点源法获得密度层化海洋中运动潜体产生的速度场,使用计入海洋内部湍流对海表面毛细重力波作用的SAR遥感全谱模式,利用考虑内波混合的湍流k-ε模式,并且使用Nasmyth海洋普适谱,建立了运动潜体湍流尾迹的SAR遥感仿真模型.利用该仿真模型对Rankine卵形体的湍流尾迹进行了仿真分析,获得令人满意的结果.     

空化射流实验研究

空化水射流技术是将空化作用引入到高压水射流而形成的一种新型高压水射流技术,在同等条件下,空化射流相对于普通高压水射流具有破碎和切割能力更高的特点。通过数值模拟和实验方法对空化技术进行研究,进行了喷嘴流场的数值模拟计算,设计了空化射流实验装置及空化喷嘴。以生锈铁板为研究对象,分别进行了喷嘴型号、打击时间、入口压力、靶距和扩散段长度的空化射流打击效果对比实验,研究了空化参数对空化效果的影响。实验结果表明角形喷嘴进行淹没射流的空化效果较好,空化射流除锈具有最优打击时间。不同的入口压力对应不同的最佳靶距。     

天地预警系统与机敏传感信息网

建立高效的天地预警系统对于赢得现代立体战争的胜利有着极其重要的意义。探讨了天地预警系统与机敏传感信息网 (Sm art Sensor Web)的构成 ,结合我国的部分研究现状 ,较详细地阐述了设计与构造天地预警系统所需解决的若干关键技术问题。     

The building evacuation problem with shared information

In this article, the Building Evacuation Problem with Shared Information (BEPSI) is formulated as a mixed integer linear program, where the objective is to determine the set of routes along which to send evacuees (supply) from multiple locations throughout a building (sources) to the exits (sinks) such that the total time until all evacuees reach the exits is minimized. The formulation explicitly incorporates the constraints of shared information in providing online instructions to evacuees, ensuring that evacuees departing from an intermediate or source location at a mutual point in time receive common instructions. Arc travel time and capacity, as well as supply at the nodes, are permitted to vary with time and capacity is assumed to be recaptured over time. The BEPSI is shown to be NP‐hard. An exact technique based on Benders decomposition is proposed for its solution. Computational results from numerical experiments on a real‐world network representing a four‐story building are given. Results of experiments employing Benders cuts generated in solving a given problem instance as initial cuts in addressing an updated problem instance are also provided. © 2008 Wiley Periodicals, Inc. Naval Research Logistics, 2008