火箭武器在登陆破障作战中的应用

在登陆作战中,障碍破除任务尤其是直前破障和陆上破障具有兵力机动困难、工作强度大、作业时限短、受敌火力威胁大和技术要求高等特点。同时,高技术条件下,岸滩障碍设置越来越复杂,抢滩登陆作战节奏快、时间紧,对破障行动的准确性和时效性提出了更高要求。目前的破障装备存在射程近、精度低、效率低等不足,难以应对瞬息万变的战场态势。近年来,随着技术的进步,火箭武器得到了较大发展,具有射程远、精度高、威力大及信息化程度高等优势,已基本具备战役全纵深内的远程精确打击能力,未来将在登陆破障作战中发挥重要作用。本文结合登陆破障作战环境和火箭武器特点及发展趋势,探索了火箭武器在登陆破障作战中的应用,以期为军队未来破障装备的发展提供可选思路。     

Numerical simulation of the blast wave of a multilayer composite charge

The numerical simulation of a blast wave of a multilayer composite charge is investigated. A calculation model of the near-field explosion and far-field propagation of the shock wave of a composite charge is established using the AUTODYN finite element program. Results of the near-field and far-field calculations of the shock wave respectively converge at cell sizes of 0.25–0.5 cm and 1–3 cm. The Euler––flux-corrected transport solver is found to be suitable for the far-field calculation after mapping. A numerical simulation is conducted to study the formation, propagation, and interaction of the shock wave of the composite charge for different initiation modes. It is found that the initiation mode obviously affects the shock-wave waveform and pressure distribution of the composite charge. Additionally, it is found that the area of the overpressure distribution is greatest for internal and external simultaneous initiation, and the peak pressure of the shock wave exponentially decays, fitting the calculation formula of the peak overpressure attenuation under different initiation modes, which is obtained and verified by experiment. The difference between numerical and experimental results is less than 10%, and the peak overpressure of both internal and external initiation is 56.12% higher than that of central single-point initiation.     

Shaped charge penetration into high- and ultrahigh-strength Steel–Fiber reactive powder concrete targets

Experiments on shaped charge penetration into high and ultrahigh strength steel-fiber reactive powder concrete (RPC) targets were performed in this paper. Results show that the variation of penetration depth and crater diameter with concrete strength is different from that of shaped charge penetration into normal strength concrete (NSC). The crater diameter of RPC is smaller than that of NSC penetrated by the shaped charge. The jet particles are strongly disturbed and hardly reach the crater bottom because they pass through the narrow channel formed by jet penetration into the RPC. The effects of radial drift velocity and gap effects of jet particles for a shaped charge penetration into RPC target are discussed. Moreover, a theoretical model is presented to describe the penetration of shaped charge into RPC target. As the concrete strength increases, the penetration resistance increases and the entrance crater diameter decreases. Given the drift velocity and narrow crater channel, the low-velocity jet particles can hardly reach the crater bottom to increase the penetration depth. Moreover, the narrow channel has a stronger interference to the jet particles with increasing concrete strength; hence, the gap effects must be considered. The drift velocity and gap effects, which are the same as penetration resistance, also have significant effects during the process of shaped charge penetration into ultrahigh-strength concrete. The crater profiles are calculated through a theoretical model, and the results are in good agreement with the experiments.     

液体火箭发动机非线性燃烧不稳定过程的并行仿真

采用计算燃烧学方法对火箭发动机非线性燃烧不稳定工作过程进行了并行数值模拟。气相控制方程组用欧拉坐标系下的Navier Stokes方程组描述 ,液相控制方程组在Lagrangian坐标系下进行描述。气、液两相作用通过方程组的源项互相耦合。编制了串行和并行程序 ,并在并行计算环境下进行了测试。从计算结果可以看出并行计算的效率较高。     

长贮过程中发动机HTPB推进剂老化机理分析

为揭示固体推进剂在长期贮存过程中的老化机理,解剖了自然贮存19年贴壁浇注的端羟基聚丁二烯橡胶推进剂装药发动机,沿着药柱径向不同位置进行了取样,并采用扫描电镜、能量色散X射线光谱仪、红外吸收光谱、交联密度等多种手段对这些样品进行了测试分析。研究发现：贴壁浇注发动机药柱不同位置推进剂的老化程度不尽相同,越靠近非金属壳体位置,推进剂的老化程度越严重。进一步深入分析表明：除了丁羟胶中双键的氧化断链和端羟基的缩合等影响推进剂老化,铝粉氧化产生的铝离子会催化丁羟胶双键与氯气或水发生加成反应生成■双键和仲醇,而铝离子迁移和分布的不均匀会引起药柱老化的不均匀性。研究结果对推进剂配方设计和防老化措施的研究具有重要意义。     

火箭出口面积对RBCC发动机引射模态影响规律分析

火箭基组合循环发动机引射模态飞行状态复杂,为了提高发动机的整体性能,研究了火箭出口面积对发动机引射模态的影响规律。通过数值模拟研究,引射流量在低飞行马赫数条件下,主要受引射性能影响,火箭出口面积越大,引射性能越好。然而,随着飞行马赫数的提升,引射空气的动能提升,隔离段内出现壅塞情况,引射流量主要受限于隔离段几何尺寸,与火箭出口面积无关。在亚声速工况下,火箭出口面积越小,发动机比冲越低,且出口无量纲面积为3.15时,火箭羽流膨胀撞壁,会引起性能骤减,需要予以避免;在超声速工况下,选择面积较小的火箭出口面积,燃烧室内压越高,发动机性能提升越明显。     

A study on the surface overpressure distribution and formation of a double curvature liner under a two-point initiation

The formation mechanism of an EFP(explosively formed projectile) using a double curvature liner under the overpressure effect generated by a regular oblique reflection was investigated in this paper.Based on the detonation wave propagation theory,the change of the incident angle of the detonation wave collision at different positions and the distribution area of the overpressure on the surface of the liner were calculated.Three-dimensional numerical simulations of the formation process of the EFP with tail as well as the ability to penetrate 45# steel were performed using LS-DYNA software,and the EFP ve-locity,the penetration ability,and the forming were assessed via experiments and x-ray photographs.The experimental results coincides with those of the simulations.Results indicate that the collision of the detonation wave was controlled to be a regular oblique reflection acting on the liner by setting the di-mensions of the unit charge and maintaining the pressure at the collision point region at more than 2.4 times the CJ detonation when the incident angle approached the critical angle.The distance from the liner midline to the boundary of the area within which the pressure ratio of the regular oblique reflection pressure to the CJ detonation pressure was greater than 2.5,2,and 1.5was approximately 0.66 mm,1.32 mm,and 3.3 mm,respectively.It is noted that pressure gradient caused the liner to turn inside out in the middle to form the head of the EFP and close the two tails of the EFP at approximately 120μs.The penetration depth of the EFP into a 45# steel target exceeded 30 mm,and there was radial expansion between the head and tail of the EFE increasing the penetration resistance of the EFP.Therefore,the structural size of the unit charge and the liner can be further optimized to reduce resistance to increase the penetration ability of the EFP.     

基于随机拟合的悬浮式深弹弹阵特征建模

通过分析悬浮式深弹发射后在空中的弹道特性,建立了深弹弹着点坐标的计算模型。采取蒙特卡洛方法,分别对舰艇六自由度状态下,单管和六联装火箭深弹的弹着点坐标进行了仿真计算,对弹着点的分布规律进行了研究,并得出弹着点的联合密度函数。结果表明,在发射参数存在正态扰动下,弹着点散布区域均呈椭圆形分布,弹着点坐标均仍服从正态分布。     

运载火箭芯级与助推级分离的数值模拟

采用动态重叠网格方法和双欧法,耦合求解非定常流动控制NS方程和6DOF运动方程,数值模拟运载火箭助推级和芯级的自由分离过程和附加外力作用下的强迫分离过程,并对芯级、助推级分离的主要影响因素进行分析。数值结果与试验结果吻合,表明动态重叠网格方法能正确预测火箭芯级与助推级间复杂的流动现象。根据数值模拟结果,给出助推级在不同分离工况下的分离参数及分离规律。     

射流角度和壁面曲率对撞壁液膜的影响

射流角度和壁面曲率是空间液体火箭发动机液膜冷却设计的重要参数,通过实验研究了入射角和壁面曲率半径对射流撞壁液膜形态和液膜厚度的影响;实验中液膜厚度的测量采用探针法法测量。对射流撞壁的溅射现象进行的分析表明,射流由壁面附着状态转变为液滴飞溅状态的临界We数为214.1,射流撞壁后由附壁状态转变为溅射状态的临界入射角度为23.1°,根据液体火箭发动机冷却的需要可以选择合适的射流角度。