基于随机拟合的悬浮式深弹弹阵特征建模

通过分析悬浮式深弹发射后在空中的弹道特性,建立了深弹弹着点坐标的计算模型。采取蒙特卡洛方法,分别对舰艇六自由度状态下,单管和六联装火箭深弹的弹着点坐标进行了仿真计算,对弹着点的分布规律进行了研究,并得出弹着点的联合密度函数。结果表明,在发射参数存在正态扰动下,弹着点散布区域均呈椭圆形分布,弹着点坐标均仍服从正态分布。     

东突恐怖主义成因分析

突厥文化和泛突厥主义的泛滥、伊斯兰复兴运动和泛伊斯兰主义的传播、新疆周边国家各种恐怖势力的影响、国际敌对势力的怂恿、改革开放以来国际交流的加强以及新疆特殊的地理位置 ,是我国新疆地区“东突”恐怖主义形成的重要条件 ,并对“东突”恐怖主义的泛滥起到了催化作用     

子母深弹反鱼雷攻击效能及仿真

火箭深弹是水面舰艇拦截鱼雷的常用武器,为提高火箭深弹拦截鱼雷的概率,提出了子母深弹的概念,将地面火炮中常用的子母弹技术应用于深弹反鱼雷攻击中,通过分析子母弹的散布特性,来比较子母深弹和火箭深弹毁伤鱼雷的效能,并通过Monte-Carlo法仿真了这一过程,分析了影响子母深弹的毁伤概率的因素。     

25nm鱼鳍型场效应晶体管中单粒子瞬态的工艺参数相关性

基于TCAD(Technology Computer-Aided Design)3-D模拟,研究了25 nm鱼鳍型场效应晶体管(Fin Field Effect Transistor,FinFET)中单粒子瞬态效应的工艺参数相关性。研究表明一些重要工艺参数的起伏会对电荷收集产生显著影响,从而影响到电路中传播的SET(Single Event Transient)脉冲宽度。对于最佳工艺拐角,离子轰击后收集的电荷量可以降低约38%,而在最坏工艺拐角下,收集的电荷量则会增加79%。这些结论对FinFET工艺下的SET减缓及抗辐射加固设计提供了一种新的思路。     

多孔材料药型罩聚能射流的形成条件

依据Herrmann状态方程和斜冲击波关系估算了多孔材料药型罩压垮之前的冲击温升,求解了经过冲击压缩卸载后材料的声速。给出了多孔材料药型罩聚能射流的形成条件。初始冲击温升会使材料的声速和强度降低,从而使多孔材料聚能射流形成射流的高速和低速条件降低。     

炸药装药在压剪加载下的起爆特点

进行了两类压剪加载实验：（１）利用石英的平面正碰撞产生压剪加载的实验,采用电磁质速法测试装药试件内部不同质点的运动情况,分析炸药装药中发生化学反应的可能性;（２）在压剪炮上采用平行倾斜碰撞产生压剪加载的实验,观测炸药装药爆炸的可能性。由实验可以看出：在亚爆轰状态的压缩加载应力条件下,剪切的联合作用对炸药的起爆起到敏化作用,适当比例的压剪加载造成更加敏感的炸药起爆响应。文中给出了起爆响应规律和响应机制的实验分析。     

Numerical simulation of the blast wave of a multilayer composite charge

The numerical simulation of a blast wave of a multilayer composite charge is investigated. A calculation model of the near-field explosion and far-field propagation of the shock wave of a composite charge is established using the AUTODYN finite element program. Results of the near-field and far-field calculations of the shock wave respectively converge at cell sizes of 0.25–0.5 cm and 1–3 cm. The Euler––flux-corrected transport solver is found to be suitable for the far-field calculation after mapping. A numerical simulation is conducted to study the formation, propagation, and interaction of the shock wave of the composite charge for different initiation modes. It is found that the initiation mode obviously affects the shock-wave waveform and pressure distribution of the composite charge. Additionally, it is found that the area of the overpressure distribution is greatest for internal and external simultaneous initiation, and the peak pressure of the shock wave exponentially decays, fitting the calculation formula of the peak overpressure attenuation under different initiation modes, which is obtained and verified by experiment. The difference between numerical and experimental results is less than 10%, and the peak overpressure of both internal and external initiation is 56.12% higher than that of central single-point initiation.     

Shaped charge penetration into high- and ultrahigh-strength Steel–Fiber reactive powder concrete targets

Experiments on shaped charge penetration into high and ultrahigh strength steel-fiber reactive powder concrete (RPC) targets were performed in this paper. Results show that the variation of penetration depth and crater diameter with concrete strength is different from that of shaped charge penetration into normal strength concrete (NSC). The crater diameter of RPC is smaller than that of NSC penetrated by the shaped charge. The jet particles are strongly disturbed and hardly reach the crater bottom because they pass through the narrow channel formed by jet penetration into the RPC. The effects of radial drift velocity and gap effects of jet particles for a shaped charge penetration into RPC target are discussed. Moreover, a theoretical model is presented to describe the penetration of shaped charge into RPC target. As the concrete strength increases, the penetration resistance increases and the entrance crater diameter decreases. Given the drift velocity and narrow crater channel, the low-velocity jet particles can hardly reach the crater bottom to increase the penetration depth. Moreover, the narrow channel has a stronger interference to the jet particles with increasing concrete strength; hence, the gap effects must be considered. The drift velocity and gap effects, which are the same as penetration resistance, also have significant effects during the process of shaped charge penetration into ultrahigh-strength concrete. The crater profiles are calculated through a theoretical model, and the results are in good agreement with the experiments.     

电荷泵中单粒子瞬变的研究

为分析电荷泵中不同频率单粒子瞬变(SET)电流对锁相环(PLL)的影响,采用频域分析法从增益和带宽的角度研究了环路参数与SET响应的关系。分析结果表明,减小环路滤波电阻可以降低系统增益,从而有效降低压控振荡器控制电压的扰动;增大固有频率或阻尼因子则可以提高系统带宽,从而滤除更大范围的SET电流,同时还可以降低PLL恢复到锁定状态的时间。因此,减小环路滤波电阻、增大固有频率或阻尼因子是有效的设计加固方法。通过1GHz PLL的SET模拟验证了上述结论。     

聚能射流侵彻下舰船钢与均质钢的等效关系

基于剩余穿深理论,依据聚能射流对钢靶板侵彻毁伤作用机理,推导出2种等效模型,并结合数值模拟建立了聚能射流侵彻下某舰船装甲钢与603钢靶板的等效关系。结果表明:当舰船钢厚度较小时,舰船钢与603装甲钢的等效厚度比约为1;当舰船钢厚度较大时,两者等效厚度比约为1.13。由此等效关系可给出用于战斗部考核性穿靶试验中相应均质靶板的确定厚度,从而为用603装甲钢靶代替该舰船钢进行聚能射流威力考核试验提供依据,达到了简化、经济、方便、有效的目的。