聚能射流侵彻下舰船钢与均质钢的等效关系

基于剩余穿深理论,依据聚能射流对钢靶板侵彻毁伤作用机理,推导出2种等效模型,并结合数值模拟建立了聚能射流侵彻下某舰船装甲钢与603钢靶板的等效关系。结果表明:当舰船钢厚度较小时,舰船钢与603装甲钢的等效厚度比约为1;当舰船钢厚度较大时,两者等效厚度比约为1.13。由此等效关系可给出用于战斗部考核性穿靶试验中相应均质靶板的确定厚度,从而为用603装甲钢靶代替该舰船钢进行聚能射流威力考核试验提供依据,达到了简化、经济、方便、有效的目的。     

利用贫铀作药型罩提高破甲威力的可行性探讨

本文对目前常规破甲弹发展陷入低谷的原因进行了分析、找出了提高破甲威力的突破口,然后从材料、实验和理论角度对采用贫铀——U~(238)作药型罩提高破甲威力的可行性进行了研究。     

充电法在复合材料静电测试中的问题

按照GJB2605－96中有关静电衰减性能测试的要求,自制了复合材料静电衰减性能测试装置。用这套测试装置对9种不同结构的复合材料进行了实验研究。研究表明,利用充电法测试材料静电衰减性能时,由于电容效应,测试结果不能正确反映被测材料的静电性能。     

信号自屏蔽电荷耦合原理及应用

本文利用静电信号高压电极自身作为传感器的屏蔽电极,使屏蔽深度与仪器灵敏度要求相一致,并使输入端接收的电荷量与被测电位成正比关系,而获得被测电位数值,提出“信号自屏蔽电荷耦合”原理,并从理论上和实验上论述了原理的正确性和先进性。利用此原理研制成ZPD-l型静电电位动态测试仪,该仪器与美制263型高速静电表、日本MH型人体静电电位仪等先进仪器相比,具有输入电阻高(>10~(14)Ω)、动态特性好,抗干扰能力强、高电压非线性失真小等特点。     

紊流时输油管道油流静电带电计算研究

对紊流条件下输油管道内油流静电带电的计算进行了研究。在合理简化紊流扩散系数和油流速度的基础上,推导出油内有关油流带电的电荷输运方程的解析解,并且根据该解析解导出了冲流电流计算公式。该计算公式同时适用于所有电导率范围内液体介质冲流电流的计算。最后利用文中推出的计算公式对一实验油道的油流带电进行了计算,结果显示公式得到的值和实验值非常吻合。     

Influence of shaped charge structure parameters on the formation of linear explosively formed projectiles

The research of LEFP (linear explosive forming projectile) is of great value to the development of new warhead due to its excellent performance. To further improve the damage ability of the shaped charge warhead, a special shell overhanging structure was designed to increase the charge based on the traditional spherical charge, in which case the crushing energy of LEFP could be guaranteed. LS-DYNA was used to simulate different charge structures obtained by changing the number of detonation points, the length of shell platform, the radius of curvature and the thickness of liner. The RSM (response surface model) between the molding parameters of LEFP and the structural parameters of charge was established. Based on RSM model, the structure of shaped charge was optimized by using multi-objective genetic algorithm. Meanwhile, the formation process of jet was analyzed by pulsed X-ray photography. The results show that the velocity, length-diameter ratio and specific kinetic energy of the LEFP were closely related to the structural parameters of the shaped charge. After the optimization of charge structure, the forming effect and penetration ability of LEPP had been significantly improved. The experimental data of jet velocity and length were consistent with the numerical results, which verifies the reliability of the numerical results.     

Effects of module number and firing condition on charge thermal safety in gun chamber

Thermal safety of modular charge which is fed into and retained in the chamber after gun fires consecutively is first investigated with cook-off method.A two-dimensional cook-off model of modular charge in gun chamber is established and the cook-off process of modular charge in gun chamber is numerically simulated.Then the effects of module number and firing condition on charge thermal safety are evaluated by researching the cook-off response characteristics of modules.The results show that,under conditions of different module numbers the cook-off responses all occur on the module closest to the boundary of missile,and the single-base propellants located at the inner surface of cartridge ignite first.When the number of loaded module changes from 1 to 6,the cook-off response temperatures vary little,only in a small range of 478.1 K-482.4 K.The cook-off response times decrease logarithmically in the range of 211.2 s-166.7 s with the increasing length of residual air gap in gun chamber.The simulation results are well matched with the experimental data.Furthermore,different firing conditions have great influence on the cook-off response time,minor influence on the initial response position and little in-fluence on the response temperature.Under the three conditions of consecutive 32 launches with 5 rounds/min,43 launches with 1 round/min,and 41 launches with different firing frequencies,the cook-off response temperatures are 479.2 K,481.1 K and 479.9 K respectively and the response times are 709.2 s,211.2 s and 214.4 s respectively.The response position is near the middle area of the inner cartridge surface in the former condition and near the right area in the latter two conditions.     

航空自导深弹和磁探仪攻潜模型与仿真

针对反潜巡逻机使用磁探仪和自导深弹的攻潜效能研究,提出了一种基于蒙特卡洛法的计算模型。在建立攻潜坐标系的基础上,给出了连投深弹射击深度的定义;结合磁探仪定位原理,提出了基于峰值追踪的定位目标和连投攻击的方法,仿真结果表明该方法能够提高命中概率;给出了目标分布和连投深弹的散布模型,依据攻潜过程和命中判定条件,进行了攻潜效能的计算;仿真分析了影响攻潜效能的主要因素,并研究了投弹间隔的确定方法。     

基于探雷信息的火箭深弹炸雷效能研究

针对火箭深弹传统炸雷方式中存在的盲目性、危险性及耗弹量大等问题,提出了火箭深弹与探雷声纳协同定点炸除水雷的方法,建立了基于随机模拟的火箭深弹炸雷效能评估模型。实例解算结果表明,火箭深弹对水雷毁伤概率随着射距的增加而增大;在同一射距下,毁伤概率随射向与探测方向夹角的增加而增大,但在最优(大)夹角附近毁伤概率变化不大。通过该模型能有效解算出火箭深弹对水雷的毁伤效果,进而得到最优射击诸元和最大毁伤概率,对火箭深弹炸雷技术实施提供了理论基础。     

基于自相关函数的信噪比估计方法

信噪比估计,作为衡量信道质量的标准,为许多自适应技术提供所需的信道信息。精确的信道质量估计值,可以有效提升这些技术的性能。研究表明,信号经过采样、发送波形成行后其自相关函数具有周期性。根据噪声和发送信号两者自相关函数的不同特性,提出一种利用自相关函数进行信噪比估计方法。仿真结果表明,该方法具有较高的估计精度。